HP SignagePlayer mp8200s Hardware Reference Guide - HP SignagePlayer mp8200 an
HP SignagePlayer mp8200s Manual
View all HP SignagePlayer mp8200s manuals
Add to My Manuals
Save this manual to your list of manuals |
HP SignagePlayer mp8200s manual content summary:
- HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 1
Hardware Reference Guide HP SignagePlayer mp8200, mp8200s - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 2
HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP Hewlett-Packard Company. Hardware Reference Guide HP SignagePlayer mp8200, mp8200s Second Edition (May 2011) - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 3
About This Book WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 4
iv About This Book - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 5
Panel Components ...3 Media Card Reader Components 4 Keyboard ...5 Using the Windows Logo Key 6 Serial Number Location ...7 2 Hardware Upgrades ...8 Serviceability Features ...8 Warnings and Cautions ...8 Connecting the Power Cord ...9 Removing the Computer Access Panel 10 Replacing the Computer - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 6
MicroSaver Security Cable Lock 30 Padlock ...31 HP Business PC Security Lock 31 Front Bezel Security 35 Appendix A Battery Replacement 37 Appendix B Electrostatic Discharge 40 Preventing Electrostatic Damage 40 Grounding Methods ...40 Appendix C - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 7
1 Product Features Standard Configuration Features Features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Figure 1-1 Configuration Standard Configuration Features 1 - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 8
icon in the Windows taskbar. NOTE: The Power On Light is normally green when the power is on. If it is flashing red, there is a problem with the computer and it is displaying a diagnostic code. Refer to the Maintenance and Service Guide to interpret the code. 2 Chapter 1 Product Features - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 9
Rear Panel Components Figure 1-3 Rear Panel Components Table 1-2 Rear Panel Components 1 Line-Out Connector for powered audio devices 6 Power Cord Connector (green) 2 PS/2 Keyboard Connector (purple) 7 TV Tuner (optional) 3 Universal Serial Bus (USB) ports 8 Line-In Audio Connector ( - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 10
Media Card Reader Components The media card reader is an optional device available on some models only. Refer to the following illustration and table to identify the media card reader components. Figure 1-4 Media Card Reader Components Table 1-3 Media Card Reader Components No. Slot Media 1 xD - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 11
Keyboard Figure 1-5 Keyboard Components Table 1-4 Keyboard Components 1 Function Keys Perform special functions depending on the software application being used. 2 Editing Keys Includes the following: Insert, Home, Page Up, Delete, End, and Page Down. 3 Status Lights Indicate the status of - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 12
Using the Windows Logo Key Use the Windows Logo key in combination with other keys to perform certain functions available in the Windows operating system. Refer to Keyboard on page 5 to identify the Windows Logo key. Table 1-5 Windows Logo Key Functions The following Windows Logo Key functions - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 13
serial number and a product ID number that are located on the top cover of the computer. Keep these numbers available for use when contacting customer service for assistance. Figure 1-6 Serial Number and Product ID Location Serial Number Location 7 - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 14
service. No tools are needed for most of the installation procedures described in this chapter. Warnings and Cautions Before performing upgrades be sure to carefully read all of the applicable instructions, cautions, and warnings in this guide This guide is located on the Web at http://www.hp.com/ - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 15
Connecting the Power Cord When connecting the power supply, it is important to follow the steps below to ensure the power cord does not pull free from the computer. 1. Connect the round end of the power cord to the power supply connector on the rear of the computer (1). 2. Insert the power cord - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 16
Removing the Computer Access Panel To access internal components, you must remove the access panel: 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all removable media, such as compact discs or USB flash drives, from the computer. 3. Turn off the computer - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 17
Replacing the Computer Access Panel 1. Align the tabs on the panel with the slots on the chassis then slide the panel towards the front of the chassis until it stops (1). 2. Tighten the thumbscrew to secure the access panel (2). Figure 2-3 Replacing the Computer Access Panel Replacing the Computer - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 18
Removing the Front Bezel 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all removable media, such as compact discs or USB flash drives, from the computer. 3. Turn off the computer properly through the operating system, then turn off any external devices. 4. - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 19
Removing a Bezel Blank On some models, there is a bezel blank covering the internal drive bay that needs to be removed before installing a drive. To remove a bezel blank: 1. Remove the access panel and front bezel. 2. To remove the bezel blank, push the two retaining tabs that hold the bezel blank - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 20
Replacing the Front Bezel Insert the three hooks on the bottom side of the bezel into the rectangular holes on the chassis (1) then rotate the top side of the bezel onto the chassis (2) and snap it into place. Figure 2-6 Replacing the Front Bezel 14 Chapter 2 Hardware Upgrades - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 21
any security devices that were disengaged when the computer cover or access panel was removed. NOTE: An optional Quick Release mounting bracket is available from HP for mounting the computer to a wall, desk, or swing arm. Changing from Desktop to Tower Configuration 15 - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 22
System Board Connections Refer to the following illustration and table to identify the system board connectors. Figure 2-8 System Board Connections No. System Board Connector System Board Label Color 1 SATA 3.0 SATA1 light blue 2 Power SATA PWR1 white 3 Mobile PCI Express Module MXM - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 23
PC3-8500 DDR3-1066 MHz-compliant or PC3-10600 DDR3-1333 MHzcompliant ● 1.5 volt DDR3-SDRAM SODIMMs The DDR3-SDRAM SODIMMs must also: ● support CAS latency 7 DDR3 1066 MHz (7-7-7 timing) and CAS latency 9 DDR3 1333 MHz (9-9-9 timing) ● contain the mandatory Joint Electronic Device Engineering Council - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 24
Populating SODIMM Sockets There are two SODIMM sockets on the system board, with one socket per channel. The sockets are labeled XMM1 and XMM3. The XMM1 socket operates in memory channel A. The XMM3 socket operates in memory channel B. Figure 2-9 SODIMM Socket Locations Table 2-1 SODIMM Socket - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 25
Installing SODIMMs CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power to drain before adding or removing memory modules. Regardless of the power-on state, voltage is always supplied to the memory modules as long as the computer is plugged into an active AC - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 26
8. To remove a SODIMM, press outward on the two latches on each side of the SODIMM (1) then pull the SODIMM out of the socket (2). Figure 2-10 Removing a SODIMM 9. Slide the new SODIMM into the socket at approximately a 30° angle (1) then press the SODIMM down (2) so that the latches lock it in - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 27
12. Reconnect the power cord and turn on the computer. 13. Lock any security devices that were disengaged when the computer cover or access panel was removed. The computer automatically recognizes the additional memory when you turn on the computer. Replacing the Optical Drive The computer uses a - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 28
7. Disconnect the cables on the rear of the optical drive (1), push the green release latch on the right rear side of the drive toward the center of the drive (2), then slide the drive forward and out of the bay through the front bezel (3). CAUTION: When removing the cables, pull the tab or - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 29
Preparing the New Optical Drive Before the new optical drive can be used, the release latch must be attached. 1. Peel the backing off the adhesive on the release latch. 2. Without allowing the release latch to touch the optical drive, carefully align the holes on the release latch with the pins on - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 30
bay before proceeding. Follow the procedures in Removing the Computer Access Panel on page 10 and Removing a Bezel Blank on page 13. 1. Follow the instructions for removing the optical drive. Refer to Removing the Optical Drive on page 21. 2. Attach the release latch to the new optical drive. Refer - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 31
Replacing the Hard Drive NOTE: The computer supports only 2.5-inch Serial ATA (SATA) internal hard access panel. 7. Remove the optical drive. Refer to Removing the Optical Drive on page 21 for instructions. 8. Press in the release latch on the left side of the hard drive carrier (1) then rotate - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 32
carrier straight up and out of the chassis. Figure 2-16 Removing the Hard Drive Carrier 10. Remove the four guide screws from the sides of the hard drive carrier. Figure 2-17 Removing the Guide Screws 11. Lift the hard drive up to the top of the carrier (1) and slide the drive out - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 33
. Figure 2-19 Sliding the Hard Drive into the Carrier 13. Set the hard drive down into the bottom of the carrier (1), then replace the four guide screws on the sides of the carrier to secure the drive in the carrier (2). Figure 2-20 Lowering the Hard Drive and Replacing the - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 34
14. To place the hard drive carrier back in the chassis, align the guide screws with the slots on the drive bay, drop the carrier straight down into the drive bay (1), and press the handle on the carrier all - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 35
Installing and Removing a Port Cover An optional rear port cover is available for the computer. To install the port cover: 1. Thread the cables through the bottom hole on the port cover (1) and connect the cables to the rear ports on the computer. 2. Insert the hooks on the port cover into the slots - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 36
Installing a Security Lock HP/Kensington MicroSaver Security Cable Lock There are two cable lock slots on the rear of the computer. The slot next to the thumbscrew should be - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 37
Padlock Figure 2-26 Installing a Padlock HP Business PC Security Lock 1. Fasten the security cable by looping it around a stationary object. Figure 2-27 Securing the Cable to a Fixed Object Installing a Security Lock 31 - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 38
2. Insert the Kensington lock into the Kensington lock slot on the back of the monitor and secure the lock to the monitor by inserting the key into the key hole on the rear of the lock and rotating the key 90 degrees. Figure 2-28 Installing the Kensington Lock on the Monitor 3. Slide the security - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 39
4. Use the bracket provided in the kit to secure other peripheral devices by laying the device cable across the center of the bracket (1) and inserting the security cable through one of the two holes in the bracket (2). Use the hole in the bracket that best secures the peripheral device cable. - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 40
6. Screw the lock to the chassis in the thumbscrew hole using the screw provided. Figure 2-32 Attaching the Lock to the Chassis 7. Insert the plug end of the security cable into the lock (1) and push the button in (2) to engage the lock. Use the key provided to disengage the lock. Figure 2-33 - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 41
be secured. Figure 2-34 Secured Workstation Front Bezel Security The front bezel can be locked in place by installing a security screw provided by HP. To install the security screw: 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all removable media, such as - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 42
7. Remove the black screw on the front of the chassis behind the bezel. The screw is located next to the optical drive and is labeled "BEZEL." Figure 2-35 Retrieving the Front Bezel Security Screw 8. Replace the front bezel. 9. Install the security screw through the middle front bezel release tab - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 43
than 60°C (140ºF). Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water. Replace the battery only with the HP spare designated for this product. CAUTION: Before replacing the battery, it is important to back up the computer CMOS settings. When the battery is - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 44
an internal component to gain access to the battery. 7. Depending on the type of battery holder on the system board, complete the following instructions to replace the battery. Type 1 a. Lift the battery out of its holder. Figure A-1 Removing a Coin Cell Battery (Type 1) b. Slide the replacement - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 45
Type 3 a. Pull back on the clip (1) that is holding the battery in place, and remove the battery (2). b. Insert the new battery and position the clip back into place. Figure A-3 Removing a Coin Cell Battery (Type 3) NOTE: After the battery has been replaced, use the following steps to complete this - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 46
work mat. If you do not have any of the suggested equipment for proper grounding, contact an HP authorized dealer, reseller, or service provider. NOTE: For more information on static electricity, contact an HP authorized dealer, reseller, or service provider. 40 Appendix B Electrostatic Discharge - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 47
C Computer Operating Guidelines, Routine Care and Shipping Preparation Computer Operating Guidelines and Routine Care Follow these guidelines to properly set up and care for the computer and monitor: ● Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ● - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 48
the finish. Safety If any object or liquid falls into the drive, immediately unplug the computer and have it checked by an authorized HP service provider. Shipping Preparation Follow these suggestions when preparing to ship the computer: 1. Back up the hard drive files on PD discs, tape cartridges - HP SignagePlayer mp8200s | Hardware Reference Guide - HP SignagePlayer mp8200 an - Page 49
USDT hard drive 25 USDT memory 17 USDT optical drive 24 USDT port cover 29 L locks USDT cable lock 30 USDT front bezel 35 USDT HP Business PC Security Lock 31 USDT padlock 31 M media card reader features 4 memory USDT installation 17 USDT socket population 18 USDT specifications 17 O optical drive
Hardware Reference Guide
HP SignagePlayer mp8200, mp8200s