HP StorageWorks 1200s HP StorageWorks NAS 1200s V1.0 Installation Guide Addend
HP StorageWorks 1200s - NAS Manual
View all HP StorageWorks 1200s manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks 1200s manual content summary:
- HP StorageWorks 1200s | HP StorageWorks NAS 1200s V1.0 Installation Guide Addend - Page 1
hp StorageWorks NAS 1200s Installation Guide Product Version: 1 This addendum applies only to the following document: HP StorageWorks NAS 1200s Installation Guide 351698-001 (September 2003) An addendum is comprised of two parts: ■ Pen-and-ink changes-provides instructions for locating specific - HP StorageWorks 1200s | HP StorageWorks NAS 1200s V1.0 Installation Guide Addend - Page 2
® is a registered trademark of The Open Group. Remove step 3, "Configure the NAS 1200s device using Chapter 3 of this guide." Page additions Insert the following sheets after page 36 of the HP StorageWorks NAS 1200s Installation Guide. Note: Consider securing this sheet into the document by using - HP StorageWorks 1200s | HP StorageWorks NAS 1200s V1.0 Installation Guide Addend - Page 3
drive into the system: 1. Remove the NAS 1200s front bezel. a. Locate the two bezel latches found on the side of the bezel. Pull the latches outward. b. Pull the front bezel away from the unit. 2. Remove a hard drive Disk as shown in Figure 8. NAS 1200s Installation Guide Addendum 1 Addendum Pg - HP StorageWorks 1200s | HP StorageWorks NAS 1200s V1.0 Installation Guide Addend - Page 4
-click the Operating System Partition, C: in this example, on the Missing disk and select Remove Mirror. In the Remove Mirror dialog box, select the Missing disk and click Remove Mirror as shown in Figure 10. 2 Addendum Pg Figure 10: Remove Mirror dialog box NAS 1200s Installation Guide Addendum - HP StorageWorks 1200s | HP StorageWorks NAS 1200s V1.0 Installation Guide Addend - Page 5
Replacing a failed hard drive e. The Mirror should now be removed from the Missing disk as show in Figure 11. Figure : If the Disk Management dialog box is displayed regarding making changes to your boot.ini file, click OK to ignore and continue. NAS 1200s Installation Guide Addendum 3 Addendum Pg - HP StorageWorks 1200s | HP StorageWorks NAS 1200s V1.0 Installation Guide Addend - Page 6
data volume and select Repair Volume as shown in Figure 14. Select the new disk, Disk 1 in this example, in the Repair RAID-5 Volume dialog box as show in Figure 15. Figure 14: Selecting Repair Volume Figure 15: Repair RAID-5 Volume dialog box 4 Addendum Pg NAS 1200s Installation Guide Addendum - HP StorageWorks 1200s | HP StorageWorks NAS 1200s V1.0 Installation Guide Addend - Page 7
the new disk, Disk 1 in this example, and select Reactivate Disk, as shown in Figure 16. Figure 16: Selecting Reactive Disk k. After the drives are repaired and the system has been rebooted, right-click the Missing disk and select Remove Disk if it is still being displayed in the Disk Management MMC
Addendum
© Copyright 2004 Hewlett-Packard Development Company, L.P.
367499-001
Printed in the U.S.A.
March 2004
Product names mentioned herein may be trademarks of their respective companies as reflected
by an associated footnote. The information in this document is subject to change without notice.
This addendum applies only to the following document:
HP StorageWorks NAS 1200s Installation Guide
351698-001 (September 2003)
An addendum is comprised of two parts:
■
Pen-and-ink changes
—provides instructions for locating specific text and for either deleting
text, replacing text with new text, or adding new text at a specific location.
■
Page additions
—identifies where to add a page at a specific place in the document and
recommends how to attach the replacement pages.
Note:
If the changes within this addendum are not incorporated into the specified documents and then
used, potential problems might arise from using obsolete information.
hp
StorageWorks
NAS 1200s Installation Guide
Product Version:
1