HP StorageWorks 2/16 HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC
HP StorageWorks 2/16 - SAN Switch Manual
 |
View all HP StorageWorks 2/16 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks 2/16 manual content summary:
- HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 1
Release Notes HP StorageWorks Fabric OS 3.1.3a Third Edition (September 2004) Part Number: AA-RUQYC-TE This document contains the latest version of these Release Notes and other Fabric OS 3.1.1x documentation, access the HP storage web site at: http://www.hp.com/country/us/eng/prodserv/storage.html. - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 2
to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 3
for installing, operating, and maintaining Fabric OS version 3.1.3. Overview HP Fabric OS 3.1.3a is a maintenance release containing fixes to a reboot for hosts that statically bind PIDs ■ Improved fabric diagnostics Supports the pathInfo command, which displays path information between any two - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 4
Documentation Supported Switches Fabric OS v3.1.3a supports the following switches: ■ HP StorageWorks SAN Switch 2/8 ■ HP StorageWorks MSA SAN switch 2/8 ■ HP StorageWorks SAN Switch 2/16 Technical Support Contact Hewlett-Packard support for hardware, firmware, and software support, including - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 5
section. 5. Locate the B-Series Fabric subsection. 6. Click the name of the appropriate switch. The switch overview page displays. 7. Locate the Product information section. 8. Click Technical documentation. 9. Select the applicable documents. For information about Fibre Channel standards, visit - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 6
with accepted engineering practices and procedures. In certain cases, HP may add proprietary supplemental functions to those specified in the standards. We verify conformance with Fibre Channel Standards by subjecting our switches to SANmark Conformance Tests developed by the Fibre Channel Industry - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 7
OS release that does not support the Extended PID format), PID needs to be set back to a supported format, such as Core PID HP also recommends that you use the most recently released firmware to control the fabric. If you use Advanced Web Tools to change the switch name, the HP StorageWorks SAN - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 8
HP recommends using Java 1.4.1_03. Two-Domain and Four-Domain Fabric Licensing If your fabric includes a switch with a license for a limited number of switches exceeds the supported switch configuration limit Gb/s switches. Installing Mozilla 1.4 on Solaris 8 and Solaris 9 For instructions to install - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 9
Notes Mozilla Browser Support for Switch Admin Module The Mozilla browser does not support the Switch Admin module properly the http://www.hp.com web site for the latest list of supported operating systems. Table 1: Browsers, Operating Systems, and Java Plug-ins Operating System HP-UX 11.00 - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 10
Important Notes Table 1: Browsers, Operating Systems, and Java Plug-ins (Continued) Operating System Red Hat Linux 8.0 Browser Mozilla 1.4 or later Java Plug-in 1.4.2_02 or later (up to but not including 1.5) Red Hat Enterprise Linux AS NN7.02 2.1 (IA32) 1.4.1_03 Red Hat Enterprise Linux AS - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 11
: Solaris Browser: Mozilla Firmware: version earlier than Fabric OS v2.6.2, v3.1.2, or v4.2.0 with secure mode enabled Operating System: Solaris Browser: Mozilla Issue and Workaround The Switch Admin does not launch correctly. Workaround: The Netscape browser is not supported by Web Tools. However - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 12
Mixed OS Versions (Continued) Launch Switch Environment Firmware: version earlier than Fabric OS v2.6.2, 3.1.2, or 4.2.0 Operating System: Any supported operating system (with supported browser) Browser: Any supported browser (on supported operating system) Firmware: Fabric OS v 2.6.2, 3.1.2, or - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 13
Important Notes Table 2: Limitations Using Mixed OS Versions (Continued) Launch Switch Environment Firmware: version earlier than Fabric OS v2.6.1, 3.0.x, or 4.0.x Operating System: Windows Browser: Internet Explorer Issue and Workaround When you are trying to run the Fabric View, - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 14
Important Notes Table 3: Fabric Watch Default Settings (Continued) Class Class Area name Description Default Settings Primitive sequence protocol error Monitors number of primitive sequence errors. Threshold Setting Unit Time Base Low High Buffer Error(s) Minute 1 60 0 Alarm Setting - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 15
Important Notes Table 3: Fabric Watch Default Settings (Continued) Class Class Area name Description Default Settings E_Port Link failure count Loss of synchronizat ion count Loss of signal count Primitive sequence protocol error Invalid transmission word Invalid CRC count Monitors number - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 16
Important Notes Table 3: Fabric Watch Default Settings (Continued) Class Class Area name Description Default Settings Fabric Copper Port Receive performance Transmit performance State changes Link failure count Loss of synchronizat ion count Monitors received rate in KB/s Monitors transmit - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 17
Important Notes Table 3: Fabric Watch Default Settings (Continued) Class Class Area name Description Default Settings Loss of signal count Monitors number of signal loss errors Primitive sequence protocol error Monitors number of primitive sequence errors Invalid transmission word - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 18
Important Notes Table 3: Fabric Watch Default Settings (Continued) Class Class Area name Description Default Settings Fabric Optic Port Link failure count Monitors number of link failures Loss of synchronization count Monitors number of loss synchronization errors. Loss of signal count - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 19
to the diagnostic messages in the HP StorageWorks Diagnostic and System Error Messages 3.1.x/4.1.x Reference Guide. If an event occurs while .x and v3.x do not support FARP requests, only ARP requests. When using IP over Fibre Channel, confirm that all host HBAs support ARP requests and issue ARP - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 20
conform to this requirement are rejected. Zoning: license To use zoning in a non-RCS (reliable commit service) mode fabric (that is, in a fabric containing switches with firmware versions other than v2.6.x, v3.1, and v4.1), HP recommends that all appropriate zoning licenses be installed on all the - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 21
that a user data stream takes to go from the source to the destination. If the user specifies the use of inactive ports or a path through a switch that does not have active routing tables to the destination, pathInfo will describe the path that would be used if the ports were active. If - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 22
reverse path or on a user-selected path (source route). For each hop, the routing information output includes the following: Hop The hop number, the local switch being hop 0. In Port Domain ID Name Out Port The port (or area) from which the frames come. For hop 0, the source port. For - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 23
, frame-truncated errors, frame-too-short errors, and encoding errors inside a frame. Reverse path In general, the path from port A on switch X to port B on switch Y might be different from the path from port B to port A. The difference could be in the links traversed between the same sequence of - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 24
the path might be different from the one the actual traffic from source to destination will take. The source route is expressed as a sequence of switches, a sequence of output ports (or areas), or a combination thereof. The next hop in the source route is described by either the output port (or area - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 25
state of the port (or area). The embedded port (-1) is used by default or if the user specifies a destination port that is not active. For a switch with blades, the destination is specified as the area; otherwise, as the port. Command output shows the reverse path in addition to the forward path - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 26
if an output port (or area) to the next hop is specified, then the user will not be prompted for the domain of the next switch; that is determined by the port (or area) specified. Default: no. Specifies that the source route must be followed strictly as indicated, skipping possible intermediate - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 27
CLI Command Updates and Changes The following example shows the pathInfo command invoked with all operands on the command line: web226:root> pathInfo Max hops: (1..127) [25] Domain: (1..239) [-1] 8 Source port: (0..15) [-1] Destination port: (0..255) [-1] Basic stats (yes, y, no, n): [no] y Extended - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 28
CLI Command Updates and Changes Target port is Embedded Hop In Port Domain ID (Name) Out Port BW Cost 0 E 9 (web226) 2 1G 1000 Port E 2 Tx Rx Tx Rx B/s (1s) - - 0 0 B/s (64s) - - 1 1 Txcrdz (1s) - - 0 - Txcrdz (64s) - - 0 - F/s (1s - - 0 0 F/s (64s) - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 29
CLI Command Updates and Changes Hop In Port Domain ID (Name) Out Port BW Cost 2 14 8 (web229) E 1 - Port 14 E Tx Rx Tx Rx B/s (1s) 0 76 0 0 B/s (64s) 5 5 5 5 Txcrdz (1s) 0 - 0 - Txcrdz (64s) 0 - 0 - F/s (1s 0 1 0 0 F/s (64s) 0 0 0 0 Words 20158695 - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 30
all users (display) admin (set/clear) Description This command affects the output displayed on the switch's console (serial port or telnet session). By default, quiet mode is turned off, and all switch tasks can send output to the console. Some output is caused by asynchronous events, such as - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 31
CLI Command Updates and Changes switchShow The switchShow command now supports the -portcount option, which returns the number of ports on the switch. The syntax is: Synopsis switchShow, "-portcount configure The Domain, R_A_TOV, and E_D_TOV fields have changed, as follows: Fields Domain R_A_TOV - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 32
Mark Timestamp. ETP Exchange Trunking Parameter. portCfgGport On the SAN Switch 2/8-EL, a fabric license is required for the portcfggport command to function properly; otherwise, a "fabric support required" message displays. portCfgLongDistance portCfgislMode and portCfgLongDistance cannot both - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 33
CLI Command Updates and Changes zonecreate The zonename operand has changed, as follows: zonename Name for a zone to be created, in quotation marks. This name cannot be used for any other zone objects. Zone names are limited to 64 characters. Fabric OS 3.1.3a Release Notes 33 - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 34
failed. This usually indicates an ASIC failure. This message is generated by the filtertest command, if problems are found. Recommended Action Replace the motherboard FRU for the SAN Switch 2/16. Replace the entire switch or the SAN Switch 2/8. Severity Critical 34 Fabric OS 3.1.3a Release Notes - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 35
message is generated by the centralmemorytest or the cmitest command, if problems are found. Recommended Action Replace the motherboard FRU for the SAN Switch 2/16. Replace the entire switch or the SAN Switch 2/8. Severity Critical DIAG-CAMINIT Message Critical DIAG-CAMINIT, 1 Probable Cause Port - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 36
cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-CAMSID Message Critical DIAG-CAMSID, 1 Probable Cause ASIC failed SID - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 37
failure. This message is generated by the statisticstest command, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-CLEAR_ERR Message Warning DIAG-CLEAR_ERR, 3 Probable - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 38
failure. This message is generated by the centralmemorytest command, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-CMBISRTO Message Critical DIAG-CMBISRTO, 1 The ASIC - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 39
. This message is generated by the centralmemorytest command, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-CMERRTYPE Message Critical DIAG-CMERRTYPE, 1 Probable - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 40
failure. This message is generated by the cmitest command, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-CMIDATA Message Critical DIAG-CMIDATA, 1 Probable Cause - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 41
failure. This message is generated by the cmitest command, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-CMINOCAP Message Critical DIAG-CMINOCAP, 1 Probable Cause - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 42
an ASIC failure. This message is generated by the cmitest command, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-CMNOBU Message Critical DIAG-CMNOBUF, 1 Probable Cause - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 43
for a faulty cable or deteriorated SFP. Replace the cable or SFP. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-ERRSTAT (2LONG) Message Critical DIAG-ERRSTAT (2LONG), 1 Probable Cause - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 44
or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-ERRSTAT (BADEOF) Message Critical DIAG-ERRSTAT (BADEOF), 1 Probable Cause - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 45
cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-ERRSTAT (CRC) Message Critical DIAG-ERRSTAT (CRC), 1 Probable Cause The - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 46
cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-ERRSTAT(CRL) Message Critical DIAG-ERRSTAT(CRL), 1 Probable Cause The - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 47
cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-ERRSTAT (ENCIN) Message Critical DIAG-ERRSTAT (ENCIN), 1 Probable Cause - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 48
or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-ERRSTAT (ENCOUT) Message Critical DIAG-ERRSTAT (ENCOUT), 1 Probable Cause - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 49
faulty cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-INIT Message Critical DIAG-INIT, 1 Probable Cause Port failed to - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 50
cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-INTNIL Message Critical DIAG-INTNIL, 1 Probable Cause ASIC failed to - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 51
failure. This message is generated by the centralmemorytest command, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-LCMEM Message Critical DIAG-LCMEM, 1 Probable Cause - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 52
failure. This message is generated by the centralmemorytest command, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-LCMRS Message Critical DIAG-LCMRS, 1 Probable Cause - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 53
generated by the centralmemorytest and the cmemretentiontest commands, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-MEMNULL Message Critical DIAG-MEMNULL, 1 Probable - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 54
RAM failure. This message is generated by the ramtest command, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-MEMSZ Message Critical DIAG-MEMSZ, 1 Probable Cause Memory - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 55
cable connections. This message is generated by the spinsilk command, if problems are found. Recommended Action Verify cable connections. Reseat the SFPs If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Fabric - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 56
cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-PORTM2M Message Critical DIAG-PORTM2M, 1 56 Fabric OS 3.1.3a Release - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 57
. Recommended Action Check for a faulty cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical Fabric OS 3.1.3a Release Notes 57 - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 58
. This message is generated by the portloopbacktest command, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-POST_SKIPPED Message Warning DIAG-POST_SKIPPED, 4 Probable - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 59
failure. This message is generated by the portregtest or the sramretentiontest commands, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical Fabric OS 3.1.3a Release Notes 59 - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 60
cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-STATS (FRX) Message Critical DIAG-STATS (FRX), 1 Probable Cause Port - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 61
cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-STATS (FTX) Message Critical DIAG-STATS (FTX), 1 Probable Cause Port - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 62
This message is generated by the turboramtest command, if problems are found. Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-TBRAM_INC_WTEST Message Critical DIAG-TBRAM_INC_WTEST, 1 Probable - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 63
faulty cable or deteriorated SFP. Replace the cable or SFP if necessary. If the problem persists: For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical DIAG-XMIT Message Critical DIAG-XMIT, 1 Probable Cause Port failed to - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 64
Fabric (BF) command. ■ HA: At F2 State: According to the Fibre Channel Specification, F2 is defined as the principal switch selection. If a failover occurs at this time, the switch is forced to restart principal switch selection. ■ HA: No Upstream: After failover, the newly active fabric thinks it - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 65
and the payload has the Pprincipal WWN and P\principal P\priority number as the principal switch. Recommended Action If the reconfiguration was unplanned, check for problems with the specified port. Some troubleshooting tasks include: Verify that the port was not disabled, using the portshow command - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 66
database exceeds the maximum size. This message can also be caused when the switch is short of memory. The value can be defined or active, Severity Error SEC-PIDCHGERR, PID Change failed: Size check failed Message Switch: , Error SEC-PIDCHGERR, 2, PID Change failed: Size check - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 67
throughout the fabric. Make sure to leave enough time so your commands do not overlap in the fabric. If the problem persists, reboot or power cycle the switch. Severity Error SEC-PIDCHGINFO Message Switch: , Info SEC-PIDCHGINFO, 4, PID Change: Success Probable Cause The PID format of the - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 68
for changed policies.) ■ secVersionReset: Secure fabric version stamp has been reset. ■ secFCSFailover: The primary FCS has failed over to a new switch. ■ All password changes: A, B, C account passwords have been changed. (A, B, C are account names for which passwords are changed.) ■ configDownload - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 69
, 3, Switch PID format changed to Format 2 ('Extended Edge PID Format'). Probable Cause The PID format for the fabric has been changed to Format 2, extended-edge PID. For more information on PID format, refer to the HP StorageWorks Fabric OS Version 3.1.x/4.1.x Procedures User Guide. Recommended - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 70
Documentation Updates Documentation Updates This section provides information on last-minute additions or corrections to documentation. HP StorageWorks SAN Switch 2/16 Installation Guide (Part Number: AA-RR84D-TE) On page 82, Table 9: The Temperature condition refers to the ambient air temperature - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 71
L2" portcfglongdistance modes. For information about these modes and Extended Fabrics in general, refer to the HP StorageWorks Extended Fabrics Version 3.1.x/4.1.x User Guide. To: "...Trunking is supported for normal E_Ports (referred to as L0 in the portcfglongdistance command) with LWL media up to - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 72
Updates HP StorageWorks Zoning Version 3.1.x/4.1.x User Guide (Part Number: AA-RS26C-TE) On page 30, after the heading "Detailed Zone Configuration Procedures," add the following: Note: The maximum number of items that can be stored in the zoning configuration database depends on the switches in - HP StorageWorks 2/16 | HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQYC - Page 73
Also, remove the following row from Table 24: VC Encoded Address Mode Set this mode only if the fabric includes a StorageWorks SAN switch. When set, the frame source and destination address use an address format that is compatible with StorageWorks SAN switches. Fabric OS 3.1.3a Release Notes 73
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
 |
 |
Release Notes
HP
StorageWorks
Fabric OS 3.1.3a
Third Edition (September 2004)
Part Number:
AA–RUQYC–TE
This document contains information about Fabric OS version 3.1.3a. In the event of conflicting
information between these Release Notes and other documents in this product release, the
Release Notes take precedence.
For the latest version of these Release Notes and other Fabric OS 3.1.1x documentation, access
the HP storage web site at:
.