HP StorageWorks 2/16V HP StorageWorks SAN Switch rack mount kit installation i
HP StorageWorks 2/16V - SAN Switch Manual
View all HP StorageWorks 2/16V manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks 2/16V manual content summary:
- HP StorageWorks 2/16V | HP StorageWorks SAN Switch rack mount kit installation i - Page 1
Supported devices Use the SAN Switch Rack Mount Kit to install the following switch models: • SAN Switch 2/8V • SAN Switch 2/8 • SAN Switch 2/8-EL • SAN Switch 2/16V • SAN Switch 2/16 • SAN Switch 2/16N • SAN Switch 2/32 • SAN Switch 4/32 • SAN Switch 4/32B • 4/8 SAN Switch • 4/16 SAN Switch • 4/64 - HP StorageWorks 2/16V | HP StorageWorks SAN Switch rack mount kit installation i - Page 2
rail 14 #8-32 x 3/16-inch Phillips panhead screws with thread lock for use with the SAN Switch 2/32 only. 14 #8-32 x 5/16-inch Phillips panhead SEMS screws for use with the 4/8, 4/16, 4/32, 4/64 SAN and 4/32B SAN Switches, and the 2/16, 2/ 8V, 2/16V, MP Router, 400 MP Router, 8/8, 8/24, 8/40, 8/80 - HP StorageWorks 2/16V | HP StorageWorks SAN Switch rack mount kit installation i - Page 3
brackets with two #10-32 x 1/2-inch Phillips panhead screws and two #10 alignment washers, as shown in Figure 2. Figure 1 Installing the rear mounting brackets (HP 10000 Series Rack) Figure 2 Installing the rear mounting brackets (HP System/e Rack) NOTE: The SAN Switch Rack Mount Kit contains - HP StorageWorks 2/16V | HP StorageWorks SAN Switch rack mount kit installation i - Page 4
rails Device model #8-32 x 5/16-inch screws #8-32 x 3/16inch screws SAN Switch 2/16 SAN Switch 2/8V SAN Switch 2/16V Ten (five per rail) N/A SAN Switch 2/32 N/A Twelve (six per rail) 4/8 SAN Switch 4/16 SAN Switch SAN Switch 4/32 Ten (five per rail) N/A 4/32B SAN Switch Six (three per - HP StorageWorks 2/16V | HP StorageWorks SAN Switch rack mount kit installation i - Page 5
AC OK Figure 6 Securing the inner rails to the MP Router MR 25007a ! IOIOI SPD LNK MR 2 5018b Figure 7 Securing the inner rails to the 4/64 SAN Switch NOTE: For factory integration only, tighten the #8-32 x 5/16-inch Phillips panhead SEMS screws and torque between 6 and - HP StorageWorks 2/16V | HP StorageWorks SAN Switch rack mount kit installation i - Page 6
plenum included in the switch accessory kit: • SAN Switch 2/8V • SAN Switch 2/16 • SAN Switch 2/16V • 4/8 SAN Switch • 4/16 SAN Switch • 4/32B SAN Switch • 8/8 SAN Switch • 8/24 SAN Switch See "Installing the plenum (if required)" on page 6 for installation instructions. If you are not installing
HP StorageWorks
SAN Switch rack mount kit
installation instructions
© Copyright 2004-2009 Hewlett-Packard Development Company,
L.P.
Eighth edition: June 2009
The information in this document is subject to change without notice.
Printed in the US
www.hp.com
A7511-90904
About this document
This document describes how to use the SAN Switch Rack Mount Kit
(part number A7511A) to rack mount SAN switches and routers.
Supported devices
Use the SAN Switch Rack Mount Kit to install the following switch models:
•
SAN Switch 2/8V
•
SAN Switch 2/8
•
SAN Switch 2/8-EL
•
SAN Switch 2/16V
•
SAN Switch 2/16
•
SAN Switch 2/16N
•
SAN Switch 2/32
•
SAN Switch 4/32
•
SAN Switch 4/32B
•
4/8 SAN Switch
•
4/16 SAN Switch
•
4/64 SAN Switch
•
8/8 SAN Switch
•
8/24 SAN Switch
•
8/40 SAN Switch
•
8/80 SAN Switch
•
FCoE Converged Network Switch
•
Encryption SAN Switch
•
Multi-protocol (MP) Router
•
400 Multi-protocol (MP) Router
Supported HP custom racks
Use the SAN Switch Rack Mount Kit with the following HP StorageWorks
custom racks only:
•
HP 9000 Series Rack
•
HP 10000 Series Rack
•
HP 10000 G2 Series Rack
•
HP System/e Rack
NOTE:
In this document, “HP 10000 Series Rack” refers to both the HP
10000 Series Rack and the HP 10000 G2 Series Rack.
Related documentation
For the latest B-series switch product documentation, see the
storage
section on the following HP website:
h
t
tp://w
w
w
.hp
.co
m/su
ppo
r
t/man
uals
Page 1