HP StorageWorks MSA2312fc HP StorageWorks 2000 Family Modular Smart Array chas
HP StorageWorks MSA2312fc Manual
 |
View all HP StorageWorks MSA2312fc manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks MSA2312fc manual content summary:
- HP StorageWorks MSA2312fc | HP StorageWorks 2000 Family Modular Smart Array chas - Page 1
air management modules, power supply modules, controller modules, and I/O modules from the failed chassis and installing them into the replacement chassis of an HP StorageWorks 2000 Family Modular Smart Array. NOTE: Make sure you obtain the latest version of these instructions from http://www.hp.com - HP StorageWorks MSA2312fc | HP StorageWorks 2000 Family Modular Smart Array chas - Page 2
the drive slot as far as it will go. 3. Rotate the latch downward until the latch clicks closed. 3.5-inch drive modules NOTE: 3.5-inch air management modules are removed using the same procedure as removing 3.5-inch drive modules. 1. Press and slide the release latch button to the right. 2. Pull - HP StorageWorks MSA2312fc | HP StorageWorks 2000 Family Modular Smart Array chas - Page 3
air management modules are installed using the same procedure as installing 3.5-inch drive modules. 1. Push the latch release button to the right. 2. Slide the drive module into the drive slot as far as it will go. 3. Rotate the latch toward the right until it clicks closed. Removing controller - HP StorageWorks MSA2312fc | HP StorageWorks 2000 Family Modular Smart Array chas - Page 4
controller (2); turn the thumbscrews finger-tight. 3. Pull the I/O module straight out of the enclosure. Service Service 1 2 2 Removing I/O modules 1. Turn the thumbscrews until the screws disengage from the I/O module. Service Service Service • On the controller and I/O modules,
-
1 -
2 -
3 -
4
 |
 |
Page 1
508267-001
About this document
The chassis field replacement unit (FRU) replaces a chassis that has
been damaged or whose midplane has been damaged. To make a
fully functional chassis, you must install the following components
from the replaced (damaged) chassis:
•
All drive modules and air management modules
•
Two power supply modules
•
One or two controller modules (for a controller enclosure)
•
One or two I/O modules (for a drive enclosure)
This document details procedures for removing drive modules/air
management modules, power supply modules, controller modules,
and I/O modules from the failed chassis and installing them into the
replacement chassis of an HP StorageWorks 2000 Family Modular
Smart Array.
NOTE:
Make sure you obtain the latest version of these
instructions from
. Select MSA SAN
Arrays, select your product, and go to Support.
Before you begin
•
Turn the power supply modules off and disconnect the power
cables.
•
Disconnect and label all cables.
CAUTION:
Parts can be damaged by electrostatic discharge.
Use proper anti-static protection:
•
Keep the replacement component in the ESD bag until needed.
•
Wear an ESD wrist strap grounded to an unpainted surface of
the chassis.
•
If an ESD wrist strap is unavailable, touch an unpainted surface
of the chassis before handling the component.
•
Never touch connector pins.
Removing air management and drive
modules
2.5-inch air management modules
1.
Squeeze the top and bottom latch release buttons to disengage
the module, and pull the module straight out of the enclosure.
Printed on at least 50% total recycled fiber with at least 10%
post-consumer paper
© Copyright 2008 Hewlett-Packard Development Company, L.P.
First edition: November, 2008
Product names mentioned herein may be trademarks of their
respective companies as reflected by an associated footnote. The
information in this document is subject to change without notice.
Printed in China.
www.hp.com
HP StorageWorks
2000 Family Modular Smart
Array
chassis and midplane
replacement instructions