HP StorageWorks MSA2324fc HP StorageWorks 2000 Family Modular Smart Array chas
HP StorageWorks MSA2324fc Manual
View all HP StorageWorks MSA2324fc manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks MSA2324fc manual content summary:
- HP StorageWorks MSA2324fc | HP StorageWorks 2000 Family Modular Smart Array chas - Page 1
into the replacement chassis of an HP StorageWorks 2000 Family Modular Smart Array. NOTE: Make sure you obtain the latest version of these instructions from http://www.hp.com/go/msa. Select MSA SAN Arrays, select your product, and go to Support. Before you begin • Turn the power supply modules off - HP StorageWorks MSA2324fc | HP StorageWorks 2000 Family Modular Smart Array chas - Page 2
2.5-inch drives 1. Press down on the latch release button. 3. Pull the module straight out of the enclosure. 2. Lift the latch until it is fully open, and then pull the module straight out of the enclosure. Installing drive modules 2.5-inch drive modules 1. Press down on the latch release button, - HP StorageWorks MSA2324fc | HP StorageWorks 2000 Family Modular Smart Array chas - Page 3
latch toward the right until it clicks closed. Removing controller modules 1. Turn the thumbscrews until the screws disengage from the controller. 2. Press both latches downward to disconnect the module from the midplane. Removing power supply modules 1. Turn the thumbscrew until it is disengaged - HP StorageWorks MSA2324fc | HP StorageWorks 2000 Family Modular Smart Array chas - Page 4
supply modules, check that the Input Power Source Good LED (top) is on. • On the controller and I/O modules, check that the OK LED (back) illuminates green, indicating that the module has completed initializing and is online. Additional information See the MSA web site: http://www.hp.com/go/msa
Page 1
508267-001
About this document
The chassis field replacement unit (FRU) replaces a chassis that has
been damaged or whose midplane has been damaged. To make a
fully functional chassis, you must install the following components
from the replaced (damaged) chassis:
•
All drive modules and air management modules
•
Two power supply modules
•
One or two controller modules (for a controller enclosure)
•
One or two I/O modules (for a drive enclosure)
This document details procedures for removing drive modules/air
management modules, power supply modules, controller modules,
and I/O modules from the failed chassis and installing them into the
replacement chassis of an HP StorageWorks 2000 Family Modular
Smart Array.
NOTE:
Make sure you obtain the latest version of these
instructions from
. Select MSA SAN
Arrays, select your product, and go to Support.
Before you begin
•
Turn the power supply modules off and disconnect the power
cables.
•
Disconnect and label all cables.
CAUTION:
Parts can be damaged by electrostatic discharge.
Use proper anti-static protection:
•
Keep the replacement component in the ESD bag until needed.
•
Wear an ESD wrist strap grounded to an unpainted surface of
the chassis.
•
If an ESD wrist strap is unavailable, touch an unpainted surface
of the chassis before handling the component.
•
Never touch connector pins.
Removing air management and drive
modules
2.5-inch air management modules
1.
Squeeze the top and bottom latch release buttons to disengage
the module, and pull the module straight out of the enclosure.
Printed on at least 50% total recycled fiber with at least 10%
post-consumer paper
© Copyright 2008 Hewlett-Packard Development Company, L.P.
First edition: November, 2008
Product names mentioned herein may be trademarks of their
respective companies as reflected by an associated footnote. The
information in this document is subject to change without notice.
Printed in China.
www.hp.com
HP StorageWorks
2000 Family Modular Smart
Array
chassis and midplane
replacement instructions