HP StorageWorks Modular Smart Array 1000 HP StorageWorks SFP Transceiver Repla
HP StorageWorks Modular Smart Array 1000 Manual
View all HP StorageWorks Modular Smart Array 1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks Modular Smart Array 1000 manual content summary:
- HP StorageWorks Modular Smart Array 1000 | HP StorageWorks SFP Transceiver Repla - Page 1
Printed in the USA. SFP Transceiver Replacement Instructions First Edition (April 2004) Part Number: 360173-001 About this document This document details the procedures for replacing a failed SFP Transceiver in HP StorageWorks Modular Smart Array (MSA) storage systems. Verifying component failure - HP StorageWorks Modular Smart Array 1000 | HP StorageWorks SFP Transceiver Repla - Page 2
precautions: ■ Do not open any panels, operate controls, make adjustments, or perform procedures to a laser device instructions provided in the new component package. Additional information For additional information, refer to the MSA technical documents web site at http://www.hp.com/go/msa1000
hp
StorageWorks
SFP Transceiver
SFP Transceiver Replacement Instructions
First Edition (April 2004)
Part Number: 360173-001
If the product in which this part is being replaced is still under HP
warranty, then the replacement part(s) referred to in these Replacement
Instructions is provided under the terms and conditions of the
Hewlett-Packard Company Limited Warranty for that product.
A copy of
this Limited Warranty may be viewed at:
If this is a trade sale part (product out of warranty), then the replacement
part(s) referred to in these Replacement Instructions is provided under HP’s
express limited warranty statement, which may be viewed at:
2330100.doc
The replacement part takes on either the Limited Warranty Period of the
part being replaced or a ninety-day period that begins upon installation
of the replacement part, whichever is greater.
The information contained on these replacement instructions is subject to
change without notice.
The only warranty for this replacement product is
as noted above.
Nothing in these replacement instructions should be
construed as constituting an additional warranty.
The information
provided in these replacement instructions is provided “AS IS” and HP is
not liable for technical or editorial errors or omissions contained herein.
© Copyright 2004 Hewlett-Packard Development Company, L.P.
Please note that this document is protected by federal copyright law and
that no part of this document may be copied, reproduced or translated
without the prior written consent of Hewlett-Packard Development
Company, L.P.
Replacement
Instructions
These instructions apply to the MSA1000
product family. The part may also be used
in other HP products. Please refer to
documentation for your specific product
for detailed replacement instructions.
360173- 001
About this document
This document details the procedures for replacing a failed
SFP Transceiver in HP StorageWorks Modular Smart Array
(MSA) storage systems.
Verifying component failure
Before replacing the SFP transceiver, use the following
methods to verify the component failure.
■
Check the controller LCD for one of the error messages
listed in Table 1.
■
If both the 1G and 2G LEDs on the Fibre Channel board are
not lit, the SFP may be faulty.
Before you begin
Read the following cautions and information before beginning
removal and replacement procedures.
Caution:
Be sure the replacement part is available before
removing the failed component.
Caution:
Parts can be damaged by electrostatic discharge.
Use proper anti-static protection. Refer to the
documentation that shipped with your system for additional
information.
Caution:
It is important to follow these instructions when
replacing components in the MSA. If the procedure is done
improperly, it is possible to lose data or damage
equipment.
WARNING:
To reduce the risk of injury from laser
radiation or damage to the equipment, observe the
following precautions:
■
Do not open any panels, operate controls, make
adjustments, or perform procedures to a laser device
other than those specified herein.
■
Do not stare into the laser beam when panels are
open.
Note:
Before replacing the SFP transceiver it is important to stop all
system access (for example: application, system I/O, or RAW device
file path/s) to the device.
Table 1:
LCD Error Messages
No.
Message
515
FIBRE DEVICE HARDWARE FAILURE
516
FIBRE SUBSYSTEM LINK FAILURE
Printed in the USA.