HP StorageWorks Modular Smart Array 1000 HP StorageWorks SCSI I/O Module with
HP StorageWorks Modular Smart Array 1000 Manual
 |
View all HP StorageWorks Modular Smart Array 1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks Modular Smart Array 1000 manual content summary:
- HP StorageWorks Modular Smart Array 1000 | HP StorageWorks SCSI I/O Module with - Page 1
in other HP products. Please refer to documentation for your specific product for detailed replacement instructions. About this document This document details the procedures for replacing a failed SCSI I/O Module with Integrated EMU Indicators in HP StorageWorks Modular Smart Array (MSA) storage - HP StorageWorks Modular Smart Array 1000 | HP StorageWorks SCSI I/O Module with - Page 2
buttons on the controller. ■ The SCSI I/O Module power indicator is on. ■ No new error messages are displayed on the LCD. Returning the failed component Please follow the return instructions provided in the new component package. Additional information For additional information, refer to the MSA
-
1 -
2
 |
 |
hp
StorageWorks
SCSI I/O Module with
Integrated EMU
SCSI I/O Module with Integrated EMU Indicators Replacement
Instructions
First Edition (April 2004)
Part Number: 358189-001
If the product in which this part is being replaced is still under HP
warranty, then the replacement part(s) referred to in these Replacement
Instructions is provided under the terms and conditions of the
Hewlett-Packard Company Limited Warranty for that product.
A copy of
this Limited Warranty may be viewed at:
If this is a trade sale part (product out of warranty), then the replacement
part(s) referred to in these Replacement Instructions is provided under HP’s
express limited warranty statement, which may be viewed at:
2330100.doc
The replacement part takes on either the Limited Warranty Period of the
part being replaced or a ninety-day period that begins upon installation
of the replacement part, whichever is greater.
The information contained on these replacement instructions is subject to
change without notice.
The only warranty for this replacement product is
as noted above.
Nothing in these replacement instructions should be
construed as constituting an additional warranty.
The information
provided in these replacement instructions is provided “AS IS” and HP is
not liable for technical or editorial errors or omissions contained herein.
© Copyright 2004 Hewlett-Packard Development Company, L.P.
Please note that this document is protected by federal copyright law and
that no part of this document may be copied, reproduced or translated
without the prior written consent of Hewlett-Packard Development
Company, L.P.
Replacement
Instructions
These instructions apply to the MSA1000
product family. The part may also be used
in other HP products. Please refer to
documentation for your specific product
for detailed replacement instructions.
358189- 001
About this document
This document details the procedures for replacing a failed
SCSI I/O Module with Integrated EMU Indicators in
HP StorageWorks Modular Smart Array (MSA) storage
systems.
Verifying component failure
Before replacing the module, use the following methods to
verify the component failure.
■
If the EMU indicator on the front panel
1
is not blinking, it
indicates a failure.
■
If the fault indicator
3
is amber, it indicates a fault.
Figure 1:
Front panel LED indicators
■
If the SCSI I/O Module power indicator
1
is off it indicates
a failure.
Figure 2:
SCSI I/O Module LED indicators
■
Check the controller LCD for one of the error messages
listed in Table 1.
1
EMU Indicator
2
Power indicator
3
Fault Indicator
1
Power indicator
2
Port activity
3
Port activity
Table 1:
LCD Error Messages
No.
Message
23
SCSI SUBSYSTEM HARDWARE FAILURE
311
EMU FLASH FAILED
412
STORAGE BOX #<n> EMU NOT RESPONDING
1
2
3
15078
1
2
3
15079
Printed in the USA.