HP StorageWorks b3000 Installation Guide for the b3000 v1 - Technical White Pa
HP StorageWorks b3000 - NAS Manual
View all HP StorageWorks b3000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks b3000 manual content summary:
- HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 1
and configure a StorageWorks NAS b3000 v1. This guide uses Quick Restore version 2.12 for the b3000. The purpose of this document is to guide customers and field engineers in the procedures required to install NAS distribution software and then update the system with current service packs, hotfixes - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 2
[Enter your Document Title] [Document Restriction Notice] Creating a Virtual Server with Terminal Services 26 Creating Cluster File Share Resources with the WEBUI 27 Creating Cluster File Share Resources with Terminal Services 27 2 - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 3
covered in the document can be located in the Administration guides for the respective products. The NAS b3000 v1 Quick Restore CD should be labeled version 2.12. 1. Place the StorageWorks NAS Executor b3000 Quick Restore CD into the CDROM drive on the b3000. With the CD in the CDROM tray, reboot or - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 4
may refresh the device list manually by selecting the Refresh button. 9. Select the unconfigured StorageWorks NAS device from the device list. This launches the WebUI configuration application (Rapid Startup) on the target StorageWorks NAS device. 10. Follow the instructions on the screen to input - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 5
Configuring and Updating the System Rapid Startup [Document the StorageWorks NAS Data Copy fix for uninstall problem from the following link: http://h18006.www1.hp.com/support/files/server 1, SWVR patch 2 or the Compaq StorageWorks Virtual Replicator Service Patch 116B. They are all installed with - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 6
[Enter your Document Title] [Document Restriction Notice] NOTE: Make sure to run the Rapid Startup Utility on both nodes before continuing 5 - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 7
Cluster Services". The only patch required is the Compaq SANworks Virtual Replicator Update. (SoftPaq 2829) http://h18006.www1.hp.com/support/files/server/us/download/16247.html Installation Instructions for stand-alone systems: 1. Place the Smart Component in a temporary directory on the NAS system - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 8
"C:\Program Files\Compaq\SANWorks Virtual Replicator 2.5." 18. Copy the file "C:\CP002829\VRRegMon.exe to the directory "C:\Program Files\Compaq\SANWorks Virtual Replicator 2.5." 19. Restart the system. 7 - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 9
the MSA firmware: o http://h18006.www1.hp.com/products/storageworks/softwaredrivers /msa1000/v238.html • The SAN guide, or copy it elsewhere and view it on a separate system. Checklists for Cluster Server Installation This checklist assists in preparing for installation. Step-by-step instructions - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 10
On On Presented At this point all nodes should be on. Table 1. Power Sequencing for Cluster Installation To configure the Cluster service on the StorageWorks NAS server, the login account must have administrative permissions on each node. Both nodes must be member servers within the same domain - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 11
and add the following Dword value: o HKEY_LOCAL _MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters o Value Name: DisableDHCPMediaSense o Data Type: Reg_Dword o Data: 1 WARNING : Using Registry Editor incorrectly can cause serious problems that may require you to reinstall your operating - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 12
[Enter your Document Title] [Document Restriction Notice] (http://support.microsoft.com/support/kb/articles/Q242/4/30.ASP) should be followed and the node rebooted prior to installing the Cluster service. If this procedure is not completed, and the second node is powered off while installing the - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 13
first, and then continue with this guide. Install Cluster Service Software and Configuring the First Node Note: During installation of Cluster service on the first node, the second accept the condition that the Cluster service is supported on hardware from the Hardware compatibility List only. 12 - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 14
[Enter your Document Title] [Document Restriction Notice] Figure 7. Hardware Configuration Certification Screen 7. Because this is the first node in the cluster, the cluster must be created. Select the first node in the cluster, as shown in Figure 8 below and then click Next. 13 - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 15
: By default, all SCSI disks not residing on the same bus as the system disk will appear in the Managed Disks list. Therefore, if the node has box shown in Figure 9 specifies which shared disks will be used by Cluster service. Add or remove disks as necessary and then click Next. Figure 9. Add - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 16
nodes and other connections through a public network. If you have more than one private network, make sure that each uses a different subnet, as Cluster service recognizes only one network interface per subnet. This document is built on the assumption that only two networks are in use. It shows how - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 17
[Enter your Document Title] [Document Restriction Notice] Figure 10. Public Network Connection 17. The next dialog box shown in Figure 11 configures the private network. Make sure that the network name and IP address correspond to the network interface used for the private network. 18. Check the - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 18
top of the list. In normal operation this connection will be used for cluster communication. In case of the Private Cluster Connection failure, cluster service will automatically switch to the next network on the list-in this case Public Cluster Connection. Make sure the first connection in the list - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 19
networks. It uses the subnet mask to select the correct network. 23. Click Finish to complete the cluster configuration on the first node. The Cluster Service Setup Wizard completes the setup process for the first node by copying the files needed to complete the installation of Cluster - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 20
as for the first node. During installation of the second node, the first node must be running. Follow the same procedures used for installing Cluster service on the first node, with the following differences: 1. In the Create or Join a Cluster dialog box, select The second or next node in the - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 21
Enter the password for the account (if there is one) and click Next. 5. At the next dialog box, click Finish to complete configuration. 6. The Cluster service will start. Click OK. 7. Close Add/Remove Programs. Verify Installation There are several ways to verify a successful installation of Cluster - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 22
[Enter your Document Title] [Document Restriction Notice] Congratulations. You have completed the installation of Cluster service on both nodes. The server cluster is fully operational. 21 - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 23
select NEXT. 11. On the "Upgrade Services for Unix" page, click the "Click here to Start the Upgrade Process". This will reboot NODE B. When the process is complete select NEXT. 12. Depending on the version of the system image an upgrade of StorageWorks NAS Data Copy may also be necessary - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 24
services and confirm that the Virtual Replicator Registry Cleanup Tool Service is installed and started. • If this service serious problems that may require you to reinstall your operating system. You hp.com/support/files/server/us/download/16247.html Installation Instructions for clustered systems - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 25
\SANWorks Virtual Replicator 2.5." 20. Shutdown and restart the system. 21. Repeat steps 1-20 on the second node [Document Restriction Notice] Note: Do not install the SWVR patch 1, SWVR patch 2 or the Compaq StorageWorks Virtual Replicator Service Patch 116B. They are all installed with the image - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 26
about SWVR can be located in the Administration Guide for the respective product. Creating a SWVR Pool in. This can not be accomplished through terminal services; it must be done locally at the console Virtual Servers Through server clusters, StorageWorks NAS enables the creation of virtual servers - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 27
• Enter the name and select NEXT. • Verify the parameters and select FINISH to create the resource. Creating a Virtual Server with Terminal Services Open Cluster administrator. Cluster administrator can be opened by selecting Start->Run>cluadmin • Select FILE->NEW->GROUP • Type the name for the new - HP StorageWorks b3000 | Installation Guide for the b3000 v1 - Technical White Pa - Page 28
share and select NEXT. • Verify the parameters and select FINISH to create the resource. Creating Cluster File Share Resources with Terminal Services In a cluster configuration file shares must be created in cluster administrator to be cluster aware. To create a cluster aware file share resource
Installation guide for the b3000 v1
This guide will provide the steps necessary to install and configure a StorageWorks NAS
b3000 v1. This guide uses Quick Restore version 2.12 for the b3000. The purpose of this
document is to guide customers and field engineers in the procedures required to install
NAS distribution software and then update the system with current service packs, hotfixes,
and SoftPaqs relevant to the StorageWorks NAS products.
This guide is for new
installations only, and does not contain steps for migrating data from an existing
installation.
table of contents
March, 2003
hp storage
technical
white paper
Introduction
2
Quick Restore
2
Rapid Launch
2
Configuring and Updating the System
4
Rapid Startup
4
SAN Connection Tool
6
Connecting to MSA1000
6
Patching SWVR in a non-clustered architecture
6
Installing Cluster Services
8
Checklists for Cluster Server Installation
8
Shared Disk Requirements:
8
Installation Overview
9
Setting up Networks
9
Configure the Public Network Adapter
11
Install Cluster Service Software
12
Configuring the First Node
12
Validating the Cluster Installation
18
Configuring the Second Node
19
Verify Installation
20
Upgrading SWVR and SFU to be cluster aware
22
Creating Pools and Virtual Disks
25
Creating a SWVR Pool through the WEBUI
25
Creating Cluster Virtual Servers and Cluster aware file share resources.
25
Creating a Virtual Server with the WEBUI
26
1