HP Superdome SX2000 Installation Guide, Sixth Edition - HP Integrity Superdome - Page 17

Tools Required, Unpacking the Cabinet, T-10, and T-30 Torx drivers

Get HP Superdome SX2000 PDF manuals and user guides View all HP Superdome SX2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Tools Required The following tools are required to unpack and install the system: • Standard hand tools, such as a adjustable-end wrench • ESD grounding strap • Digital voltmeter capable of reading ac and dc voltages • 1/2-inch socket wrench • 9/16-inch wrench • #2 Phillips screwdriver • Flathead screwdriver • Wire cutters or utility knife • Safety goggles or glasses • T-10, T-15, T-20, T-25, and T-30 Torx drivers • 9-pin to 25-pin serial cable (HP part number 24542G) • 9-pin to 9-pin null modem cable Unpacking the Cabinet WARNING! Use three people to unpack the cabinet safely. HP recommends removing the cardboard shipping container before moving the cabinet into the computer room. NOTE: If unpacking the cabinet in the computer room, be sure to position it so that it can be moved into its final position easily. Notice that the front of the cabinet (Figure 1-3) is the side with the label showing how to align the ramps. To unpack the cabinet, follow these steps: Unpacking and Inspecting the System 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Tools Required
The following tools are required to unpack and install the system:
•
Standard hand tools, such as a adjustable-end wrench
•
ESD grounding strap
•
Digital voltmeter capable of reading ac and dc voltages
•
1/2-inch socket wrench
•
9/16-inch wrench
•
#2 Phillips screwdriver
•
Flathead screwdriver
•
Wire cutters or utility knife
•
Safety goggles or glasses
•
T-10, T-15, T-20, T-25, and T-30 Torx drivers
•
9-pin to 25-pin serial cable (HP part number 24542G)
•
9-pin to 9-pin null modem cable
Unpacking the Cabinet
WARNING!
Use three people to unpack the cabinet safely.
HP recommends removing the cardboard shipping container before moving the cabinet into the
computer room.
NOTE:
If unpacking the cabinet in the computer room, be sure to position it so that it can be
moved into its final position easily. Notice that the front of the cabinet (
Figure 1-3
) is the side
with the label showing how to align the ramps.
To unpack the cabinet, follow these steps:
Unpacking and Inspecting the System
17