HP Superdome SX2000 Installation Guide, Sixth Edition - HP Integrity Superdome - Page 62

Running JET Software, Running JUST

Get HP Superdome SX2000 PDF manuals and user guides View all HP Superdome SX2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Figure 1-52 Power Status Showing State of UGUY LEDs 4. Verify that there is an asterisk (*) in the columns marked MP, CLU, and PM. IMPORTANT: An asterisk (*) appears in the MP column only for cabinet 0; that is, the cabinet containing the MP. Verify that there is an asterisk (*) for each of the cells installed in the cabinet by comparing what is in the Cells column with the cells located inside the cabinet. Running JET Software To ensure that the network diagnostic is enabled at the MP prompt, enter the nd command; MP:CM>nd. You must run nd to run scan and to do firmware updates to the system. The JTAG Utility for Scan Tests (JUST) Exploration Tool (JET) collects system information for each system on a network and places it in files for use by other scan tools. JET gathers configuration data by executing a series of queries targeted at the MP and the CLU portion of the UGUY board. IMPORTANT: You must resolve any problems you find as a result of running JET before booting the operating system. Running JUST To run JUST to ensure that the hardware is working properly, follow these steps: 1. Enter jet_setup at the Windows® SMS command window or enter scan_setup at the HP-UX SMS command window. 2. Enter the complex_name, IP address, and system type. 3. Enter jet -s . 4. Enter just -s . 62 Installing the System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Figure 1-52 Power Status Showing State of UGUY LEDs
4.
Verify that there is an asterisk (*) in the columns marked MP, CLU, and PM.
IMPORTANT:
An asterisk (*) appears in the MP column only for cabinet 0; that is, the
cabinet containing the MP.
Verify that there is an asterisk (*) for each of the cells installed in the cabinet by comparing
what is in the
Cells
column with the cells located inside the cabinet.
Running JET Software
To ensure that the network diagnostic is enabled at the MP prompt, enter the nd command;
MP:CM>nd
. You must run nd to run scan and to do firmware updates to the system.
The JTAG Utility for Scan Tests (JUST) Exploration Tool (JET) collects system information for
each system on a network and places it in files for use by other scan tools. JET gathers
configuration data by executing a series of queries targeted at the MP and the CLU portion of
the UGUY board.
IMPORTANT:
You must resolve any problems you find as a result of running JET before booting
the operating system.
Running JUST
To run JUST to ensure that the hardware is working properly, follow these steps:
1.
Enter
jet_setup
at the Windows
®
SMS command window or enter
scan_setup
at the
HP-UX SMS command window.
2.
Enter the complex_name, IP address, and system type.
3.
Enter
jet -s <complex_name>
.
4.
Enter
just -s <complex_name>
.
62
Installing the System