HP V241 User Guide
HP V241 Manual
 |
View all HP V241 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP V241 manual content summary:
- HP V241 | User Guide - Page 1
HP V241a/V241 LED Backlit Monitor User Guide - HP V241 | User Guide - Page 2
and/or other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors - HP V241 | User Guide - Page 3
; The monitor (and the pedestal) Stand Power cord VGA cable DVI cable (Optional) Audio cable (only for V241a) Documentation and software Disc Setup poster Warranty certificate (Optional) If any of these items are missing, please contact your dealer for technical support and custom service. Note - HP V241 | User Guide - Page 4
Chapter II. Installation 2.1 Install the pedestal Please follow the steps illustrated below to install the pedestal. 3 - HP V241 | User Guide - Page 5
2. Connect the 15-Pin ends of the signal cable to the VGA port of your monitor and the VGA OUT jack on the back of your computer. Secure the screws on cord into the electrical outlet to avoid damaging the monitor. 2. During installation, please support the front frame with your hand at its center of - HP V241 | User Guide - Page 6
2.3 Disconnect the pedestal for shipping Press the clip button on the pedestal and remove the pedestal from the stand. 5 - HP V241 | User Guide - Page 7
Chapter III. Monitor overview Overview of front panel controls 6 - HP V241 | User Guide - Page 8
Chapter IV. Operational Instruction 4.1 Power ON/OFF Switch Press this button to power on/off your monitor. Note: The ON/OFF switch does not disconnect your monitor from the main voltage. To completely disconnect the main voltage, please remove the power plug from the socket. 4.2 Power indicator The - HP V241 | User Guide - Page 9
4.4 OSD operational instructions Icon Main menu option Submenu option Note To adjust the brightness level of the Brightness screen. The factory default range is 90. To adjust the - HP V241 | User Guide - Page 10
to VGA input). Selects the method on how displayed information on the monitor will be formatted.Select Custom Scaling Fill to Screen - image fills for adjusting the on-screen display(OSD)control. To adjust OSD position for your monitor. To adjust the visual position of the OSD menu to the right or - HP V241 | User Guide - Page 11
. The factory default setting is "30 seconds". Auto-Sleep Mode Power Saver Mode Power-On Recall Mode Display Monitor Status DDC/CI support To select the function of power management for your monitor. To enable the energy-saving function, Select On off The factory default setting is On. The "Power - HP V241 | User Guide - Page 12
mode. Timer - Set "On' or "Off" status for the Sleep Timer. The default setting is "Off". Sleep Now - to activate the sleep mode for your monitor Selects the language in which the OSD menu is displayed.The factory default is English. To select and display important information about your - HP V241 | User Guide - Page 13
EXIT video input signal sources may take you several seconds. Exits the OSD menu screen. 12 - HP V241 | User Guide - Page 14
Chapter V. Technical Information 5.1 Factory preset display mode Criteria 1 2 3 4 5 6 7 8 9 10 Resolution 640X480 @60 Hz 720X400 @70 Hz 800X600 @60 Hz 1024X768 @60 Hz 1280X720 @60 Hz 1280X1024 @ 60 Hz 1440X900 @60 Hz 1600X900 @60 Hz 1680X1050@60 Hz 1920X1080@ 60Hz Horizontal frequency 31.469 31. - HP V241 | User Guide - Page 15
5.2 Product specifications Size Max. resolution Recommended resolution Horizontal frequency Vertical frequency Viewable size Viewable angle Pitching angle Pixel frequency OSD functions Size (Packing) Net weight/ Gross weight Power supply Altitude (under operational condition) Altitude (under - HP V241 | User Guide - Page 16
5.3 Signal cable connector PIN Signal 1 Red Signal 2 Green Signal 3 Blue Signal 4 Ground 5 Cable testing 6 Red Signal Ground 7 Green Signal Ground 8 Blue Signal Ground 9 5 VDC 10 Null 11 Ground 12 SDA (for DDC) 13 Horizontal synchronization 14 Vertical synchronization - HP V241 | User Guide - Page 17
PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 DVI Interface SIGNAL TMDS Data 2 TMDS Data 2 + TMDS Data 2 / 4 Shield TMDS Data 4 TMDS Data 4 + DDC Clock DDC Data No Connect TMDS Data 1 TMDS Data 1 + TMDS Data 1 / 3 Shield TMDS Data 3 TMDS Data 3 + +3.3/+5V Power (from PC) Ground - HP V241 | User Guide - Page 18
PIN SIGNAL 1 GND 2 LEFT AUDIO CHANAL 3 RIGHT AUDIO CHANAL 4 GND 5 GND Audio interface（Only for V241a） 5.4 Panel testing The ratio of valid pixels on each LCD screen reaches 99.99% or higher. However, less than 0.01% of the pixels may cause dark dots displayed on the screen. 17 - HP V241 | User Guide - Page 19
reduce the risk of serious injury, read the Safety and Comfort Guide. It describes proper workstation, setup, posture, and health and work and correctly sized furniture designed to properly support your HP LCD monitor. WARNING! LCD monitors that are inappropriately situated on dressers, bookcases - HP V241 | User Guide - Page 20
to determine the ampere rating (Amps or A) for each device. Install your monitor near a power outlet that you can easily reach. Disconnect the monitor by grasping the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord. Do not allow anything to rest on the - HP V241 | User Guide - Page 21
this product yourself. Adjust only those controls that are covered in the operating instructions. If your monitor is not operating properly or has been dropped or damaged, contact your HP authorized dealer, reseller, or service provider. ● Use only a power source and connection appropriate for this - HP V241 | User Guide - Page 22
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there changes or modifications made to this device that are not expressly approved by HP may void the user's authority to operate the equipment. Cables To maintain - HP V241 | User Guide - Page 23
the "GS" approval mark, when forming part of a system comprising HP brand computers, keyboards and monitors that bear the "GS" approval mark, meet the applicable ergonomic requirements. The installation guides included with the products provide configuration information. Power Cord Set Requirements - HP V241 | User Guide - Page 24
an authorized HP service provider. A power cord should be routed so that it is of user inactivity. When used with an external ENERGY STAR○R qualified display, this feature also supports similar power management features for the display. To take advantage of these potential energy savings, users - HP V241 | User Guide - Page 25
for certain categories of electronic products offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, visit http://www.hp.com/go/jisc0950. Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its - HP V241 | User Guide - Page 26
. For VGA input, Auto-adjustment will solve problems of this kind. The optimum resolution of the monitor is not available Make sure the graphic card supports optimum resolution. Make sure latest applicable driver for graphic card is installed. For HP and Compaq systems, you may download the latest - HP V241 | User Guide - Page 27
the customer service department by visiting HP technical support website at: www.hp.com/support Select the country / territory where you are. Follow the link to visit pages applicable to your monitor. Preparing to Call Technical Support If you cannot solve a problem by using the troubleshooting tips
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
 |
 |
HP V241a/V241 LED Backlit Monitor
User Guide