HP VS80 DLT VS80 Tape Drive Installation Poster
HP VS80 - StorageWorks DLT VS 80 Tape Drive Manual
 |
UPC - 613326404355
View all HP VS80 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP VS80 manual content summary:
- HP VS80 | DLT VS80 Tape Drive Installation Poster - Page 1
2003) Part Number: 289066-003 [bar code goes here in text box, if applicable] 289066- 003 About this document This document provides instructions for installing the HP StorageWorks DLT VS80 Tape Drive. Detailed, translated versions of these instructions can be found in the reference guide on the - HP VS80 | DLT VS80 Tape Drive Installation Poster - Page 2
the DLT VS80 tape drive, locate the terminator in the accessories package and press it firmly into either of the two SCSI connectors on the rear panel of the drive. Secure the terminator by tightening the screws until snug. Device drivers Device drivers for Intel-based systems can be downloaded from
-
1 -
2
 |
 |
See other side
hp
StorageWorks
DLT VS80 Tape Drive
DLT VS80 Tape Drive Installation Instruction
Third Edition(September 2003)
Part Number: 289066-003
© Copyright 2003 Hewlett-Packard Development Company, L.P.
Hewlett-Packard Company makes no warranty of any kind with regard to
this material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlett-Packard shall
not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this
material.
This document contains proprietary information, which is protected by
copyright. No part of this document may be photocopied, reproduced,
or translated into another language without the prior written consent of
Hewlett-Packard. The information contained in this document is subject to
change without notice.
Product names mentioned herein may be trademarks of their respective
companies as reflected by an associated footnote.
Hewlett-Packard Company shall not be liable for technical or editorial
errors or omissions contained herein. The information is provided “as is”
without warranty of any kind and is subject to change without notice. The
warranties for Hewlett-Packard Company products are set forth in the
express limited warranty statements for such products. Nothing herein
should be construed as constituting an additional warranty.
289066- 003
Installation
Instructions
About this document
This document provides instructions for installing the HP
StorageWorks DLT VS80 Tape Drive.
Detailed, translated versions of these instructions can be found in
the reference guide on the enclosed documentation CD.
Unpacking the tape drive
Caution:
If the room where you are unpacking the drive
differs from the temperature at which the tape drive was
shipped or stored by 30º F (15º C) or more, let the drive
acclimate to the surrounding environment for at least 12
hours before opening the shipping carton.
Figure 1:
Unpacking the tape drive
Note:
Save the packing materials in case you need to move or ship
the drive in the future. You must ship the DLT VS80 tape drive in the
original or equivalent packing materials to preserve your warranty.
Required tools
Figure 2:
Required tools
Installing the internal tape drive
Setting the SCSI ID
Figure 3:
SCSI ID settings
Note:
When setting the SCSI ID:
■
Make sure that each SCSI device on a SCSI bus has a
unique SCSI ID.
■
Do not use SCSI ID 7. It is reserved for the controller.
Installing the tape drive
Caution:
Electrostatic discharge (ESD) can damage
electronic components. Be sure you are properly grounded
before beginning this procedure. Refer to Appendix B,
“Electrostatic Discharge,” in the
HP StorageWorks DLT VS80
Tape Drive Reference Guide
for additional information.
Figure 4:
Removing power from all devices
Caution:
Failure to remove power from all devices could
result in damage to the DLT VS80 tape drive or other devices.
Note:
Your server may differ from the following illustrations. Different
rails or cover removal from a drive bay may be required. Refer to the
documentation included with your server.
Figure 5:
Inserting the tape drive
Note:
An LVD/SE SCSI host adapter must be present in the server.
Terminating the tape drive
If the DLT VS80 tape drive is the only SCSI device – other than
the SCSI host adapter – on the selected server, it must be
terminated. Likewise, if the DLT VS80 tape drive is the last
device on the selected server SCSI bus, it must be terminated.
Figure 6:
Ribbon cable with terminator
The DLT VS80 tape drive ships with a ribbon cable that is
already terminated as shown in
Figure 6
. If you use a cable other
than the one provided, be sure that the cable is terminated at each
end.
Figure 7:
Connecting the power and signal cable
External drive:
Small screwdriver
Internal drive:
Phillips screwdriver
Torx-15 screwdriver
SCSI ID
SCSI ID Jumpers
0
1
2
3
4
5
6
Jumper
Block
7
1
Terminated SCSI cable
2
Power connector
SELECT
ENTER
EJECT
1
2