HP Visualize b1000 hp Visualize c3600 UNIX workstations PA8600 upgrade instruc
HP Visualize b1000 - Workstation Manual
View all HP Visualize b1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Visualize b1000 manual content summary:
- HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 1
HP VISUALIZE C3600 UNIX® Workstations PA8600 Upgrade Instructions Manufacturing Part Number: A5997-90000 Edition E1299 © Copyright 1999 by Hewlett-Packard - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 2
to another language without the prior written consent of Hewlett-Packard Company. Hewlett-Packard Warranty Statement Refer to Warranty & Support for your HP Workstation for warranty terms applicable to your Hewlett-Packard product and replacement parts. Restricted Rights Legend Use, duplication - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 3
UNIX is a registered trademark in the United States of America and other countries, licensed exclusively through X/Open Company Limited. © Copyright 1980, 1984 AT&T, Inc. © Copyright 1979, - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 4
4 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 5
1 Getting Started The following important information must be adhered to for proper removal and replacement of all Hewlett-Packard parts. 5 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 6
Getting Started CAUTION This upgrade process should be performed by experienced hardware users only. 6 Chapter 1 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 7
HP replacement part in your B1000/C3000 workstation does not affect the regulatory and safety classifications or approvals listed in the original owner's guide following the instructions on the package. Attach the sticky end of the wrist strap to bare metal on the rear panel of the workstation. • - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 8
Getting Started Safety Warnings strap, clips attached to the wrist strap, nodes, and peripheral units. • Keep uninstalled printed circuit boards in their protective antistatic bags. • Once you have removed printed circuit boards from their protective antistatic bags, handle the printed circuit - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 9
Part Kit Contents Take a moment to verify that your kit contains the following contents: • System board upgrad tray assembly • Electrostatic Discharge (ESD) materials • Removal/Replacement Instructions If you are missing any part or any documentation, please call your designated - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 10
Getting Started Required Tools Required Tools You will need the following tools for removal/replacement procedures: • T-10 and/or T-15 Torque drivers • ESD materials • Sufficient ESD protected surfaces on which to lay out parts 10 Chapter 1 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 11
guide for the actual step-by-step procedures for upgrading the B1000/C3000 to a C3600. 1. Prepare your workstation - Verify that you have the correct version of HP cables. 13. Reinsert the PCI I/O card(s). 14. Reinstall the air divider. 15. Reinsert the memory cards (DIMMs). 16. Reinstall the hard - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 12
-UX. 1. Determine the workstation's LAN ID by entering the following command: /usr/sbin/lanscan. The output is similar to the following: Hardware Station Crd Hardware Net-Interface NM MAC HP DLPI Mjr Path Address In# State NameUnit State ID Type Support Num 2.0.2 0x08000970ECC0 0 UP lan0 UP 4 ETHER - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 13
by simply pressing the power switch on the front panel of the workstation. Also, power off the monitor and any attached peripheral devices. If necessary, shut down the workstation by executing "shutdown -h" as user root. This ensures that all programs are terminated and all data is saved before - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 14
parts overview of the B1000/C3000 workstation. Figure 1-1 Exploded View I/O Fan/Speaker Bracket I/O Fan stem-Board Fans Speaker Chassis I/O Card Retainer Clip Front-Panel Display Air Divider Power Supply Hard Disk Tray Side Panel System Board DIMMs (Memory) Memory Fan CD Drive T Floppy - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 15
Getting Started Product Exploded Diagram Chapter 1 15 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 16
Getting Started Product Exploded Diagram 16 Chapter 1 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 17
2 System Board Removal/Replacement This chapter describes how to remove and replace the System Board for the B1000/C3000 workstation. 17 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 18
terminators with cables to external peripheral devices, remove those cables., LAN cable, USB cables, and any other cables from the back of the workstation. Removing all Terminators and Cables Serial Ports USB Ports LAN Port Parallel Port Audio In/Out Ports SCSI Terminators Power Plug 18 Chapter - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 19
in the top and bottom right edge of the back side of the workstation, as shown below. Figure 2-2 Opened Side Panel Side-Panel Thumbscrew Hinge Slots outward as shown above. Unhinge the panel and pull it away from the workstation. Set the panel and its screws aside. Only the left side panel - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 20
a cushioned surface to protect the exterior of the system from damage. 2. Position the conductive sheeting so that an inch of one edge is under the workstation and the rest is flat against the work area to lay system components on after you remove them. Also ensure that your static-grounding strap - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 21
power supply: three system power cables and the SCA hard disk backplane cable. Location of Power Cables Power Cables 6. Remove the power supply from the workstation: a. Holding the power supply handle, remove the bail from the bail Chapter 2 21 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 22
2-4 on page 21). b. Slide the spring hinge lever toward the front of the workstation and rotate it downward to lock it in place (see Figure 2-4 on page 21). c. Slide the power supply toward the back of the workstation to disengage it from the right hinge pin, remove the power supply and set - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 23
System Board Removal/Replacement Removing the Hard Disk Fan Figure 2-6 Fan Power Cable Removing the Hard Disk Fan 1. Locate the memory DIMMs. The hard disk fan is to the right of these. 2. Disconnect the power cable from the system board that drives the hard-disk fan. - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 24
/Replacement Removing the Memory Cards (DIMMs) Figure 2-7 Removing the Memory Cards (DIMMs) 1. Press downward on the ejector tabs located on each side of the memory card (DIMM) slot. Removing a DIMM 2. Grasp the memory card by its edges and lift it straight out. Place the card on the conductive - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 25
Divider 1. Remove the PCI retainer clip by pulling evenly in the direction of the "Pull" tabs on the clip and lifting it out of the workstation. Removing the Air Divider PCI Retainer Clip Air Divider 2. Remove the two T-15 Torx screws that secure the air divider to the chassis. 3. Note the - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 26
for re-assembly. Figure 2-9 1. Looking down on the PCI cards, remove the bulkhead screw for each PCI card. Removing the PCI Cards' Bulkhead Screws Bulkhead screws (remove from inside) Typical PCI Card 2. Grasp the edges of each PCI card and pull it up and out of the workstation. 26 Chapter 2 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 27
Figure 2-10 Removing the PCI Cards System Board Removal/Replacement Removing the PCI I/O Card(s) 3. Repeat Steps 1 and 2 above to remove all the PCI I/O cards. Chapter 2 27 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 28
System Board Removal/Replacement Disconnecting the Cables Disconnecting the Cables 1. Disconnect the following nine cables from the system board: • Fan cables for top and bottom system-board fans and I/O fan • Power cable for CD drive • Data cables for CD drive and floppy drive • Front-panel display - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 29
Figure 2-11 Cable locations Drive ta Connector p Sys. Board Fan wer Connector ppy Drive ta Connector ttom Sys. Board Fan wer Connector ra 2 Wide LVD SI Connector System Board Removal/Replacement Disconnecting the Cables I/O Fan Power Connec Speaker Connec Front-Panel Disp Connector CD Drive Powe - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 30
damage, make sure your static-grounding strap is securely attached to your wrist and to the bare metal on the workstation. Figure 2-12 Removing the old System Board 1. Ensure all workstation cables are out of the way to avoid interference or damage when you remove the system board tray. Removing - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 31
board tray's keyholes with the standoffs on the side wall of the chassis, and then slide the system board tray toward the back of the workstation to seat the standoffs into their corresponding keyholes. 2. Replace the two T-15 Torx screws that secure the system board tray to the rear wall of - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 32
System Board Removal/Replacement Reconnecting Cables Reconnecting Cables 1. Connect the following nine cables to their respective connectors on the system board (which, for clarity, is again shown outside the chassis): • Fan cables for top and bottom system-board fans and I/O fan • Power cable for - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 33
Figure 2-13 Connecting the Cables Drive ta Connector p Sys. Board Fan wer Connector ppy Drive ta Connector System Board Removal/Replacement Reconnecting Cables I/O Fan Power Connec Speaker Connec Front-Panel Disp Connector CD Drive Powe Cable Connec ttom Sys. Board Fan wer Connector ra 2 Wide LVD - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 34
on the back of the workstation. Figure 2-14 1. Align the edges of the PCI card with its slot and firmly push down to connect the card to the system board. Visually inspect and confirm the connection between the I/O card and the system board. Installing the PCI Cards 2. Looking down on the PCI - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 35
System Board Removal/Replacement Reinserting PCI I/O Cards Figure 2-15 Inserting the PCI Cards' Bulkhead Screws Bulkhead screws (insert from inside) Typical PCI Card 3. Repeat Steps 1 and 2 above to install all the PCI I/O cards. Chapter 2 35 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 36
2-16 Reinstalling the Air Divider 1. Slide the air divider into the workstation. 2. Replace the two T-15 Torx screws-one on the back and divider, and then pushing upward and inward-making sure that all the PCI cards' edges are aligned properly with the individual retainers on the clip-until the - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 37
ejector tabs will angle upward as the memory card is inserted. Refer to the memory installation label inside the system for replacing the DIMMs in the correct slots. Reinstalling a DIMM 2. Visually inspect and confirm the connection between the memory card and the system board. 3. Repeat steps 1 and - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 38
Hard Disk Fan 1. Locate the area next to the DIMMs from which the fan was removed. 2. Align the hard-disk fan with the fan bracket guide and slide it into place, making sure the tabs engage the holes in the chassis. The fan will click into place. Reinstalling the Hard Disk - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 39
System Board Removal/Replacement Reinstalling the Power Supply Figure 2-19 Spring Hinge Reinstalling the Power Supply 1. To install the power supply: a. Pick up the power supply by the handle and position its right-side hinge pin into the right side hinge bracket, as shown below. b. Align the - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 40
System Board Removal/Replacement Reinstalling the Power Supply Figure 2-20 Location of Power Cables Power Cables 3. Lift the handle edge of the power supply enough to allow the bail lock to be disengaged from the bail, fold the bail lock down, and the lower the power supply back into place. 4. - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 41
System Board Removal/Replacement Reinstalling the Power Supply Figure 2-21 Power Supply Screws and Handles T15 Torx Thumbscrew Power Supply Handle T15 Torx Thumbscrew 5. Carefully tip the workstation back to the upright position. Chapter 2 41 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 42
its top and bottom hinge hooks with their respective slots in the chassis. Swing the back edge of the panel toward the back of the workstation and press the panel firmly into place. Figure 2-22 Opened Side Panel Side-Panel Thumbscrew Hinge Slots 1 Side-Panel Hook 2 2. Replace the two T-15 Torx - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 43
3 Wrapping Up This section contains information to help you confirm that your removal and replacement procedure was successful. In some cases you will need to use specific HP-UX commands and utilities to reconfigure the workstation to recognize the replacement part(s). 43 - HP Visualize b1000 | hp Visualize c3600 UNIX workstations PA8600 upgrade instruc - Page 44
other cables that were disconnected when opening the workstation. 2. Reconnect all peripheral devices and their Problems chapter of the B1000/C3000 Owner's Guide. If you have any questions, suggestions, or problems with our hardware or documentation, please contact your designated Hewlett-Packard
HP V
ISUALIZE
C3600 UNIX
®
Workstations
PA8600
Upgrade Instructions
Manufacturing Part Number: A5997-90000
Edition E1299
© Copyright 1999 by Hewlett-Packard