HP Visualize c3000 hp workstation b1000 and c3000 - pa8700 upgrade instruction
HP Visualize c3000 - Workstation Manual
View all HP Visualize c3000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Visualize c3000 manual content summary:
- HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 1
HP VISUALIZE C3700 UNIX® Workstations PA8700 Upgrade Instructions Manufacturing Part Number: A6058-90000 Edition E0501 © Copyright 2001 by Hewlett-Packard - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 2
Hewlett-Packard Company. Hewlett-Packard Warranty Statement Refer to Warranty & Support for your HP Workstation for warranty terms applicable to your Hewlett-Packard another language without the prior written consent of Hewlett-Packard Company. UNIX is a registered trademark in the United States of - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 3
Hewlett-Packard parts HP replacement part in your B1000/C3000 workstation does not affect the regulatory and safety classifications or approvals listed in the original owner's guide instructions on the package. Attach the sticky end of the wrist strap to bare metal on the rear panel of the workstation - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 4
contents: • System board upgrad tray assembly • Electrostatic Discharge (ESD) materials • Removal/Replacement Instructions If you are missing any part or any documentation, please call your designated service representative. Required Tools You will need the following tools for removal/replacement - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 5
new system board. - Power off the workstation and any peripherals. - Unplug the power. 2. Remove the Current Bezel Label and Attach New Labels 3. Remove the terminators and cables. 4. Remove the side panel. 5. Remove the power supply. 6. Remove the hard disk fan. 7. Remove the memory cards (DIMMs - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 6
to update HP-UX. 2. Determine the workstation's LAN ID by entering the following command: /usr/sbin/lanscan. The output is similar to the following: Hardware Station Crd Hardware Net-Interface NM MAC HP DLPI Mjr Path Address In# State NameUnit State ID Type Support Num 2.0.2 0x08000970ECC0 - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 7
B1000/C3000 Workstation Safely Powering Down the B1000/C3000 Workstation You must complete the following steps before performing any of the removal and replacement procedures: CAUTION Do not use the power supply interlock thumbscrew on the rear panel to power down the workstation. This power down - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 8
parts overview of the B1000/C3000 workstation. Figure 1-1. Exploded View I/O Fan/Speaker Bracket I/O Fan System-Board Fans Speaker Chassis I/O Card Retainer Clip Front-Panel Display Air Divider Power Supply Hard Disk Tray Side Panel System Board DIMMs (Memory) Memory Fan CD Drive Tray - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 9
workstation's bezel and how to remove and replace the System Board for the B1000/C3000 workstation. Bezel Labels If you are upgrading your system board to change your workstation 1. Follow the procedure found in your Owner's Guide for removing the workstation's bezel. 2. Rotate the bezel over so - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 10
's bezel. These labels were shipped with your upgrade kit. To attach these labels to your workstation's bezel, follow these steps: 1. Insert the rivets of the bezel label with the HP logo on it into the rivet holes at the top of the bezel. See Figure 2-3. Figure 2-3 Attaching the Top Bezel - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 11
Upgrading Your System Bezel Labels 2. Remove the protective cover from the back of the sticker labeled "hp workstation c3700" and attach it to the bezel as shown in Figure 2-4. Figure 2-4 Attaching the HP Workstation Model Number Label to the Bezel Label with Model Number Chapter 2 11 - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 12
System Removing all Terminators and Cables Removing all Terminators and Cables 1. After powering down the workstation as described in the "Getting Started" chapter, unplug the power cable from the back of the workstation. To avoid ESD damage to components, carefully follow the ESD procedures (also - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 13
in the top and bottom right edge of the back side of the workstation, as shown below. Figure 2-6 Opened Side Panel Side-Panel Thumbscrew Hinge Slots outward as shown above. Unhinge the panel and pull it away from the workstation. Set the panel and its screws aside. NOTE Only the left side - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 14
. Also ensure that your static-grounding strap is securely attached to your wrist and to bare metal on the workstation. Figure 2-7. Power Supply Screws and Handles T15 Torx Thumbscrew Power Supply Handle T15 Torx Thumbscrew 3. Alternately loosen the two T-15 Torx screws from the corners of the - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 15
the bail in the bail lock to hold the power supply upright. Figure 2-8 Tipping Up the Power Supply Spring Hinge Right-side Hinge Pin Bail Lock Bail 5. Disconnect the four cables shown below located below the raised power supply: three system power cables and the SCA hard disk backplane cable - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 16
to lock it in place (see Figure 2-8 on page 15). a. Slide the power supply toward the back of the workstation to disengage it from the right hinge pin, remove the power supply and set it aside. Removing the Hard Disk Fan 1. Locate the memory DIMMs. The hard disk fan is to the right of these - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 17
ejector tabs located on each side of the memory card (DIMM) slot. Figure 2-11 Removing a DIMM 2. Grasp the memory card by its edges and lift it straight out. Place the card on the conductive sheeting. 3. Locate the label that shows memory installation sequence for later reference. 4. Repeat steps - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 18
Divider 1. Remove the PCI retainer clip by pulling evenly in the direction of the "Pull" tabs on the clip and lifting it out of the workstation. Figure 2-12 Removing the Air Divider PCI Retainer Clip Air Divider 2. Remove the two T-15 Torx screws that secure the air divider to the chassis - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 19
' Bulkhead Screws Bulkhead screws (remove from inside) Typical PCI Card 2. Grasp the edges of each PCI card and pull it up and out of the workstation. Figure 2-14 Removing the PCI Cards 3. Repeat Steps 1 and 2 above to remove all the PCI I/O cards. Chapter 2 19 - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 20
Cables Disconnecting the Cables 1. Disconnect the following nine cables from the system board: • Fan cables for top and bottom system-board fans and I/O fan • Power cable for CD drive • Data cables for CD drive and floppy drive • Front-panel display cable • Ultra 2 Wide LVD SCSI cable • Speaker cable - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 21
avoid system damage, make sure your static-grounding strap is securely attached to your wrist and to the bare metal on the workstation. Removing the old System Board 1. Ensure all workstation cables are out of the way to avoid interference or damage when you remove the system board tray. Figure 2-16 - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 22
board tray's keyholes with the standoffs on the side wall of the chassis, and then slide the system board tray toward the back of the workstation to seat the standoffs into their corresponding keyholes. 2. Replace the two T-15 Torx screws that secure the system board tray to the rear wall of - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 23
on the system board (which, for clarity, is again shown outside the chassis): • Fan cables for top and bottom system-board fans and I/O fan • Power cable for CD drive • Data cables for CD drive and floppy drive • Front-panel display cable • Ultra 2 Wide LVD SCSI cable • Speaker cable Figure - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 24
into their original slots. Refer to the I/O slot numbers on the back of the workstation. 1. Align the edges of the PCI card with its slot and firmly push down to connect the card to the system board. Visually inspect and confirm the connection between the I/O card and the system board. Figure - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 25
Upgrading Your System Reinstalling the Air Divider Reinstalling the Air Divider 1. Slide the air divider into the workstation. 2. Replace the two T-15 Torx screws-one on the back and one on the side-that secure the air divider to the chassis. 3. Replace the - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 26
the ejector tabs will angle upward as the memory card is inserted. Refer to the memory installation label inside the system for replacing the DIMMs in the correct slots. Figure 2-21 Removing a DIMM 2. Visually inspect and confirm the connection between the memory card and the system board. 3. Repeat - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 27
the fan was removed. 2. Align the hard-disk fan with the fan bracket guide and slide it into place, making sure the tabs engage the holes in the Disk Fan Hard-Disk Fan Power Cable Fan Bracket Fan Bracket Handle DIMMs Hard Disk Fan 3. Reconnect the fan's power cable to the socket on the system - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 28
Upgrading Your System Reinstalling the Power Supply Reinstalling the Power Supply 1. To install the power supply: a. Pick up the power supply by the handle and position its right-side hinge pin into the right side hinge bracket, as shown below. b. Align the shaft of the spring - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 29
and the lower the power supply back into place. 4. Alternately tighten the two captive T-15 Torx screws in the corners of the power supply. Figure 2-25 Power Supply Screws and Handles T15 Torx Thumbscrew Power Supply Handle T15 Torx Thumbscrew 5. Carefully tip the workstation back to the upright - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 30
its top and bottom hinge hooks with their respective slots in the chassis. Swing the back edge of the panel toward the back of the workstation and press the panel firmly into place. Figure 2-26 Opened Side Panel Side-Panel Thumbscrew Hinge Slots 1 Side-Panel Hook 2 2. Replace the two T-15 Torx - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 31
to use specific HP-UX commands and utilities to reconfigure the workstation to recognize the power up, refer to the Solving Problems chapter of the Owner's Guide. If you have any questions, suggestions, or problems with our hardware or documentation, please contact your designated Hewlett-Packard - HP Visualize c3000 | hp workstation b1000 and c3000 - pa8700 upgrade instruction - Page 32
Wrapping Up Verifying System Operations 32 Chapter 3
HP V
ISUALIZE
C3700 UNIX
®
Workstations
PA8700
Upgrade Instructions
Manufacturing Part Number: A6058-90000
Edition E0501
© Copyright 2001 by Hewlett-Packard