HP W2007 1859m,2009m,2009v, 2009f, 2159m,2159v,2309m,2309v, 2509m, 2709m LCD M - Page 32

Management, Volume, Windows Vista start, button, Control Panel, Hardware and Sound - monitor driver

Get HP W2007 - 20.1inch LCD Monitor PDF manuals and user guides
UPC - 882780774742
View all HP W2007 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Troubleshooting Problem Solution (Continued) Unable to hear audio from built-in speakers. Do the following: ■ Ensure the source signal is good by using headphones at the source. ■ Press the Menu button to access the OSD menu. Select Management, and then select Volume to adjust the volume. ■ Turn up the volume with the front panel volume button. ■ Ensure speaker volume is not muted or too low: Click the Windows Vista start button , Control Panel, and Hardware and Sound. Under Audio Devices and Sound, click Adjust system volume. Under Main Volume, move the slider up. No Plug and Play. In order for the Plug and Play feature of the monitor to work, you need a computer and graphic card that are compatible with Plug and Play. Check with your computer manufacturer. Check the monitor's video cable, and make sure that none of the pins are bent. Make sure that the HP monitor drivers are installed. Refer to "Installing Drivers" in the Operating the Monitor chapter for more information. HP monitor drivers are also available at: http://www.hp.com/support Picture bounces, flickers, or wave pattern is present in the picture. Move electrical devices that may cause electrical interference as far away from the monitor as possible. Use the maximum refresh rate that your monitor is capable of at the resolution that you are using. Monitor is always in "Sleep Mode (Amber LED)." The computer power switch should be in the On position. The computer graphic card should be snugly seated in its slot. Check that the monitor video cable is properly connected to the computer. Inspect the monitor video cable, and make sure that none of the pins are bent. Check that your computer is operational: Press the Caps Lock key and observe the Caps Lock LED found on most keyboards. The LED should either turn on or off after hitting the Caps Lock key. USB 2.0 ports are not working. Make sure the USB hub cable is securely connected to the monitor and the computer. A-2 Features may vary by model. User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Troubleshooting
A–2
Features may vary by model.
User’s Guide
Unable to hear audio from
built-in speakers.
Do the following:
■
Ensure the source signal is good by using headphones at the source.
■
Press the Menu button to access the OSD menu. Select
Management
, and then select
Volume
to adjust the volume.
■
Turn up the volume with the front panel volume button.
■
Ensure speaker volume is not muted or too low: Click the
Windows Vista start
button
,
Control Panel
, and
Hardware and Sound
. Under Audio Devices and
Sound, click
Adjust system volume
. Under Main Volume, move the slider up.
No Plug and Play.
In order for the Plug and Play feature of the monitor to work, you need a computer and graphic
card that are compatible with Plug and Play. Check with your computer manufacturer.
Check the monitor’s video cable, and make sure that none of the pins are bent.
Make sure that the HP monitor drivers are installed. Refer to “Installing Drivers” in the
Operating the Monitor chapter for more information. HP monitor drivers are also available at:
Picture bounces, flickers, or
wave pattern is present in the
picture.
Move electrical devices that may cause electrical interference as far away from the monitor as
possible.
Use the maximum refresh rate that your monitor is capable of at the resolution that you
are using.
Monitor is always in “Sleep
Mode (Amber LED).”
The computer power switch should be in the On position.
The computer graphic card should be snugly seated in its slot.
Check that the monitor video cable is properly connected to the computer.
Inspect the monitor video cable, and make sure that none of the pins are bent.
Check that your computer is operational: Press the Caps Lock key and observe the Caps Lock
LED found on most keyboards. The LED should either turn on or off after hitting the Caps
Lock key.
USB 2.0 ports are not
working.
Make sure the USB hub cable is securely connected to the monitor and the computer.
Problem
Solution (Continued)