HP Workstation xw4100 SCSI Hard Drive Installation - HP Workstation xw Series
HP Workstation xw4100 Manual
View all HP Workstation xw4100 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Workstation xw4100 manual content summary:
- HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 1
-specific information, refer to the Service and Technical Reference Guide for your HP workstation at http://www.hp.com/support/workstation_manuals. NOTE: HP strongly recommends that only an HP authorized dealer, reseller, or service provider replace your primary hard drive. NOTE: HP accessories - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 2
a unique SCSI ID, you can install the hard drive into your system. NOTE: For product-specific information, refer to the Service and Technical Reference Guide for your HP workstation at http://www.hp.com/support/workstation_manuals. 1. Disconnect power from the system and remove the access panel - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 3
it snaps into place. Then attach the power and data cable to the drive. NOTE: For an HP Workstation xw4200, install two 6-32 screws into each side of the hard drive before sliding the hard drive into the bay. NOTE: If installing a hard drive into bay 5, lay the workstation on its side and remove the - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 4
not already done so, follow the applicable instructions for "Installing the Hard Drive.'' 2. Insert the SCSI controller card into an available PCI expansion slot. 3. Connect the SCSI cable to the SCSI controller card. 4. Connect the hard drive LED cable to the SCSI card and to the system board. The - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 5
a partition for the new drive using Windows 2000: 1. From the desktop click Start, point to Settings and click Control Panel. 2. Click Administrative Tools. 3. Click Computer Management. 4. Click Storage. 5. Click Disk Management. This action starts the Write Signature and Upgrade Disk Wizard. Click - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 6
12. Click Next. 13. Specify the drive letter of the partition or use the If you are working with a SCSI or SATA HDD, then the first device would be aware that Red Hat Linux (which is most likely installed on your HP system) only Red Hat Linux Installation Guide at http://www.redhat.com/docs/manuals - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 7
Systems with mkfs After you have created partitions on the disk drive using a partitioning program such as fdisk, use mkfs to create the partition. If you need more information on the various options available to you in /etc/fstab, enter man fstab. boot time and simplifies use of the mount command. 7 - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 8
visiting the HP Web site at www.hp.com/support. Warranty Refer to the warranty information that was shipped with this kit. 366429-001 © 2004 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered trademark of Hewlett-Packard Development Company, L.P. Microsoft and Windows are - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 9
http://www.jpn.hp.com/doc/manual/workstation/hp_workstation.html Web HP Service and Technical Reference Guide http://www.hp.com/support/workstation_manuals http://www.jpn.hp.com/doc/manual/workstation/hp_workstation.html 注記 : HP HP 注記 : HP HP HP は、 HP SCSI ID の設定 SCSI - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 10
1、 3 2 SCSI ID ID 3 4 つの ID ID0、 ID1、 ID2 ID3 SCSI ID SCSI ID Web HP Service and Technical Reference Guide http://www.hp.com/support/workstation_manuals http://www.jpn.hp.com/doc/manual/workstation/hp_workstation.html 1 2 5 5 4 3 2 1 2 2 1 1 5 3 10 - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 11
4 5 注記 : HP Workstation xw4200 6-32 ネジ 2 注記 : 5 5 3 5 11 - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 12
SCSI xw8200 6 SCSI SCSI SCSI 7 12 - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 13
SCSI 1 2. SCSI PCI 3. SCSI SCSI 4 LED SCSI す。 LED SCSI xw6200 5 [F1 F1 13 - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 14
3 4 5 Write Signature and Upgrade Disk 6. [Disk 1 Unallocated 3 Disk 2 Unallocated 4 Disk 3 Unallocated 7 8. [OK 9. [Unallocated Disk 10 11 12 13 14 15 16 17 18. [Choose Partition File System Partition Parameters 19 20 21 Windows 2000 Windows 2000 1 2 3 4 14 - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 15
Signature and Upgrade Disk 6. [Disk 1 Unallocated 3 Disk 2 Unallocated 4 Disk 3 Unallocated 7 8 9 10 11 12 13 14 15. [Choose Partition File System Partition Parameters 16 17 18 Linux ext3 Linux ext3 fdisk fdisk fdisk IDE 2 dev/hdb SCSI ま たは SATA HDD 1 dev - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 16
Red Hat Linux HP 1 4 5 4 1 つ (1 Web Official Red Hat Linux Installation Guide An Introduction to Disk Partitions http://www.redhat.com/docs/manuals/linux 4 Enter 5 size sizeM Enter fdisk 6 注記 : [w q mkfs によ る ext3 fdisk mkfs ext3 1 root 2. /sbin/mkfs -t ext3 /dev/ - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 17
1 root 2. pico -w /etc/fstab 3 etc/fstab /etc/fstab mount/point etc/fstab man fstab sbin/tune2fs -l /dev/hdbX |grep volume hdb X Filesystem volume name: /mount/point ext3 etc/fstab HP HP の Web www.hp.com/support 保証 17 - HP Workstation xw4100 | SCSI Hard Drive Installation - HP Workstation xw Series - Page 18
366429-001 © 2004 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered trademark of Hewlett-Packard Development Company, L.P. Microsoft Windows Microsoft Corporation Linux Linus Torvalds 18
SCSI Hard Drive Installation
HP Workstation xw Series
This document describes how to install a SCSI hard drive into an HP Workstation xw series.
Installing the New Hard Drive
Å
WARNING:
To reduce the risk of personal injury from hot surfaces, allow the internal system
components to cool before touching.
Ä
CAUTION:
Be sure that the power to the workstation is off. Disconnect the AC power cord to avoid
electrical damage to the workstation. Electrostatic discharge (ESD) can damage electronic components.
Be sure you are properly grounded before beginning this procedure. For more information, refer to the
Service and Technical Reference Guide
for your HP workstation at
NOTE:
For product-specific information, refer to the
Service and Technical Reference Guide
for your HP
workstation at http://www.hp.com/support/workstation_manuals.
NOTE:
HP strongly recommends that only an HP authorized dealer, reseller, or service provider replace
your primary hard drive.
NOTE:
HP accessories are for use in HP workstation products. They have been extensively tested for
reliability and are manufactured to high quality standards. HP, therefore, warrants only those accessories
that are manufactured or sold by HP.
Setting the SCSI ID
Before installing a SCSI hard drive in your system, you must give the hard drive a unique SCSI ID.
All SCSI controllers require a unique SCSI ID (0-15) for each SCSI device that is installed. The reserved
and available SCSI ID numbers for SCSI devices are:
■
0 is reserved for the primary hard drive (not reserved for the primary hard drive on Linux).
■
7 is reserved for the SCSI controller.
■
1 through 6 and 8 through 15 are available for all other SCSI devices.
When 0 is used for the primary hard drive, set the second hard drive to 1, the third to 2, and so on.