HP Xw4600 HP Workstations - LSI SAS 3041E Serial Attached SCSI RAID
HP Xw4600 - Workstation - 2 GB RAM Manual
UPC - 883585516483
View all HP Xw4600 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Xw4600 manual content summary:
- HP Xw4600 | HP Workstations - LSI SAS 3041E Serial Attached SCSI RAID - Page 1
LSI SAS 3041E SAS RAID HBA (RAID controller card) ● SAS driver CD ● Hard drive activity LED cables ● Installation instructions (this document) ● Warranty information Before you begin To view QuickSpecs and determine the compatibility of this product with your HP workstation, see http://www.hp.com/go - HP Xw4600 | HP Workstations - LSI SAS 3041E Serial Attached SCSI RAID - Page 2
Comfort Guide. It describes proper workstation setup, posture, health, and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located at http://www.hp.com/ergo and on the documentation CD (if one is included with the product). CAUTION - HP Xw4600 | HP Workstations - LSI SAS 3041E Serial Attached SCSI RAID - Page 3
the system BIOS updates, if available. Accessing the internal components of the workstation 1. If you need help preparing the workstation for this installation, consult the removal and replacement procedures in the service guide for your workstation at http://www.hp.com/support/ workstation_manuals - HP Xw4600 | HP Workstations - LSI SAS 3041E Serial Attached SCSI RAID - Page 4
is similar for all HP workstation models. Table 1 Data cable configuration guide HP workstation model Location of hard drive HP xw Workstation series ● HP 400 Workstations ● Internal hard drive bay Optical bay HP 600 Workstations ● Internal hard drive bay HP 600 Workstations ● Optical bay - HP Xw4600 | HP Workstations - LSI SAS 3041E Serial Attached SCSI RAID - Page 5
connect internal hard drives to the RAID controller card. NOTE: To connect hard drives located in the optical bays of HP 600 Workstations, see Connecting standard data cables on 0 cable to Port 0 on the RAID controller card. Figure 4 SAS-SATA controller ports ENWW Step 3-Configuring the cabling 5 - HP Xw4600 | HP Workstations - LSI SAS 3041E Serial Attached SCSI RAID - Page 6
have blind-mate cabling preinstalled on the system board. To connect the RAID cabling for these configurations: 1. If connecting a SAS hard drive, ensure that there is a SAS-to-SATA interconnect cable adapter (supplied with the HP workstation SAS hard drive kit) attached to the data connector on the - HP Xw4600 | HP Workstations - LSI SAS 3041E Serial Attached SCSI RAID - Page 7
Connecting the LED activity indicator on page 7. Connecting the LED activity indicator This section applies to all HP workstations shown above. Attach one end of the hard drive activity LED cable to the RAID controller card. Attach the other end of the hard drive activity LED cable to the hard drive - HP Xw4600 | HP Workstations - LSI SAS 3041E Serial Attached SCSI RAID - Page 8
updates, designated for your workstation model and operating system. Obtain updates from http://www.hp.com/go/ workstationsupport. Step 6-Configuring RAID devices For detailed instruction on configuring RAID devices, see the service guide for your HP workstation model at http://www.hp.com/support
LSI SAS 3041E Serial Attached SCSI RAID
Host Bus Adapter installation
Introduction
This document describes how to install an LSI SAS 3041E Serial Attached SCSI (SAS) Redundant Array
of Independent Disks (RAID) Host Bus Adapter (HBA) in HP
and xw Workstation series. Procedures
are included for hard drives mounted in hard drive bays and optical drive bays.
Kit contents
●
LSI SAS 3041E SAS RAID HBA (RAID controller card)
●
SAS driver CD
●
Hard drive activity LED cables
●
Installation instructions (this document)
●
Warranty information
Before you begin
To view
QuickSpecs
and determine the compatibility of this product with your HP workstation, see
go/productbulletin
.
© 2006–2009 Hewlett-Packard Development Company, L.P. Printed in the U.S.
ENWW
Introduction
1