HP Xw4600 HP xw Workstation Series - IEEE-1394 card installation
HP Xw4600 - Workstation - 2 GB RAM Manual
 |
UPC - 883585516483
View all HP Xw4600 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Xw4600 manual content summary:
- HP Xw4600 | HP xw Workstation Series - IEEE-1394 card installation - Page 1
in some kits) ● Warranty ● Installation instructions Before you begin Visit http://www.hp.com/accessories/workstations to determine the compatibility of this product with your HP workstation. ENWW © 2007 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered trademark of - HP Xw4600 | HP xw Workstation Series - IEEE-1394 card installation - Page 2
Guide. It describes proper workstation, setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ ergo and/or on the documentation CD if one is included with the product - HP Xw4600 | HP xw Workstation Series - IEEE-1394 card installation - Page 3
ground for the equipment you are working on by connecting the static-free mat, static strap and peripheral units to that piece of equipment. NOTE: HP accessories are for use in HP workstation products. They have been extensively tested for reliability and are manufactured to high quality standards - HP Xw4600 | HP xw Workstation Series - IEEE-1394 card installation - Page 4
component installation: 1. Power down the workstation. 2. Disconnect power from the workstation. 3. Open the access cover. For product-specific information, see the Service and Technical Reference Guide for your HP workstation at http://www.hp.com/support/workstation_manuals. Step 2-Removing the PCI - HP Xw4600 | HP xw Workstation Series - IEEE-1394 card installation - Page 5
the IEEE-1394 card CAUTION: To prevent damage to your workstation, observe the following Electro Static Discharge (ESD) precautions while retention clamp clips (2). The 1394 card can be installed in any PCI slot, but HP recommends installing the card in an available PCI 32-bit slot. NOTE: When the - HP Xw4600 | HP xw Workstation Series - IEEE-1394 card installation - Page 6
remove the adhesive label. HP xw8000/xw9000 series workstations Connect one connector on the Y-adapter power cable to the workstation optical drive power wire 5-Reassembling the workstation After installation, reassemble the workstation using the instructions in the workstation documentation. The - HP Xw4600 | HP xw Workstation Series - IEEE-1394 card installation - Page 7
The following table lists information to help you assemble and configure your workstation. Table 1 Configuration information xw4550 xw4000/xw6000 xw8000/xw9000 1394A ● Requires Y-adapter cable ● Power direct from power ● Power not required (function on system board) supply ● Front I/O
-
1 -
2 -
3 -
4 -
5 -
6 -
7
 |
 |
IEEE-1394 card installation
HP xw Workstation series
This document describes how to install an IEEE-1394 card in your workstation.
Kit contents
The following components are included in your IEEE-1394 card kit:
●
IEEE-1394 (A or B) card
●
Y-adapter power cable (available in some kits)
●
Warranty
●
Installation instructions
Before you begin
Visit
accessories/workstations
to determine the compatibility of this product with your
HP workstation.
© 2007 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered
trademark of Hewlett-Packard Development Company, L.P. Printed in the U.S.
ENWW
HP xw Workstation series
1