HP Xw8000 Optical Drive Installation
HP Xw8000 - Workstation - 0 MB RAM Manual
View all HP Xw8000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Xw8000 manual content summary:
- HP Xw8000 | Optical Drive Installation - Page 1
document describes how to install an optical drive on an HP Workstation. Electrostatic Discharge A discharge of static electricity for proper grounding, have an authorized dealer, reseller, or service provider install the part. NOTE: For additional information on static electricity or for assistance - HP Xw8000 | Optical Drive Installation - Page 2
front of the chassis under the front bezel or on the diskette drive bracket under the access panel. HP-supplied metric screws are black. On other workstations, the optical drives do not require these guide screws. Instead, the drive cage is equipped with a latching mechanism to secure the optical - HP Xw8000 | Optical Drive Installation - Page 3
the finish. ■ If any object or liquid falls into the cabinet, immediately unplug the workstation and have it checked by an authorized service provider. ■ When a disc is not in use, remove it from the drive and store it in its case. ■ Handle the disc by the edges, not the flat surface of the disc - HP Xw8000 | Optical Drive Installation - Page 4
the new drive. Optical Drive Bays Å WARNING: To avoid the risk of serious injury or damage to the workstation, ensure that the power cord is the appropriate drive bay. 3. If one is installed, remove the EMI filler. 4. If your optical drive requires guide screws, remove four M3 guide screws from - HP Xw8000 | Optical Drive Installation - Page 5
the optical drive cage while sliding the new drive in. Ä CAUTION: Ensure that the optical drive has been properly secured. Failure to do so may cause damage to the drive when moving the workstation. NOTE: Refer to the documentation included with your workstation for specific instructions on securing - HP Xw8000 | Optical Drive Installation - Page 6
any peripheral devices to the workstation. Enabling Digital Audio If the system is using Windows 2000 or Windows XP, enable the audio as follows: 1. From the Control Panel double-click System. 2. Click the Hardware tab, then click Device Manager. 3. Double-click DVD/CD-ROM drives. 4. Right-click the - HP Xw8000 | Optical Drive Installation - Page 7
reading information from the disc. Opens the disc tray manually. Holds the disc. Opens and closes the disc tray. NOTE: The drive bezel and drive controls may not be identical to those shown. Opening the Tray Manually If you have exited the CD application and are unable to eject the disc with the - HP Xw8000 | Optical Drive Installation - Page 8
guide on the documentation CD that came with your workstation for additional regulatory information governing this product. 365578-001 © 2004 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered trademark of Hewlett-Packard Development Company, L.P. Microsoft and Windows - HP Xw8000 | Optical Drive Installation - Page 9
HP Workstation HP 1 1MΩ ± 10 HP HP 9 - HP Xw8000 | Optical Drive Installation - Page 10
5.25 1/2 IDE M3 4 T-15 M3 HP 注意事項 CD CD CD CD CD CD CD CD 10 - HP Xw8000 | Optical Drive Installation - Page 11
CD 1 CD AC HP CD CD CD CD 1 2 3. AC 4 11 - HP Xw8000 | Optical Drive Installation - Page 12
1 2 Ä 2 3. EMI 4 M3 4 12 - HP Xw8000 | Optical Drive Installation - Page 13
5 M3 2 xw6200 や xw8200 6 13 - HP Xw8000 | Optical Drive Installation - Page 14
7 注記 : Linux CD Microsoft Windows IDE IDE 8 Windows 2000 ま たは Windows XP 1 2 3. [DVD/CD-ROM 14 - HP Xw8000 | Optical Drive Installation - Page 15
4 CD-ROM 5 CD-ROM CD 6. [OK 15 - HP Xw8000 | Optical Drive Installation - Page 16
項目 名称 1 2 3 CD 4 機能 CD CD CD CD CD 1 1.6 34.9 2 3 16 - HP Xw8000 | Optical Drive Installation - Page 17
IDE IDE ATA 0 1 IDE 項目 機能 1 0 2 1 3 VCCI B CD 365578-001 © 2004 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered trademark of Hewlett-Packard Development Company, L.P. Microsoft Windows Microsoft Corporation Linux Linus Torvalds 17 - HP Xw8000 | Optical Drive Installation - Page 18
18
1
Optical Drive Installation
for HP Workstations
This document describes how to install an optical drive on an HP Workstation.
Electrostatic Discharge
A discharge of static electricity from a finger or other conductor may damage system boards or other
static-sensitive devices. This type of damage may reduce the life expectancy of the device.
Preventing Electrostatic Damage
To prevent electrostatic damage, observe the following precautions:
■
Avoid hand contact by transporting and storing parts in static-safe containers.
■
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
■
Place parts on a grounded surface before removing them from their container.
■
Avoid touching pins, leads, or circuitry.
■
Always be properly grounded when touching an electrostatic-sensitive component or assembly.
Grounding Methods
There are several methods for grounding. Use one or more of the following measures when handling or
installing electrostatic- sensitive parts:
■
Use a wrist strap connected by a ground cord to a grounded workstation chassis. Wrist straps are
flexible straps with a minimum of 1 meg. ohm +/- 10 percent resistance in the ground cords. To
provide a proper ground, wear the strap snug against the skin.
■
Use heelstraps, toestraps, or bootstraps at standing workstations. Wear the straps on both feet when
standing on conductive floors or dissipating floor mats.
■
Use conductive field service tools.
■
Use a portable field service kit with a folding static-dissipating work mat.
If you do not have any of the suggested equipment for proper grounding, have an authorized dealer,
reseller, or service provider install the part.
NOTE:
For additional information on static electricity or for assistance with the installation of this
product, contact an authorized dealer, reseller, or service provider.