HP Z400 HP 22-in-1 Media Card Reader Installation
HP Z400 - Workstation Manual
 |
UPC - 890552660926
View all HP Z400 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Z400 manual content summary:
- HP Z400 | HP 22-in-1 Media Card Reader Installation - Page 1
reader and bracket into an HP computer. Basic troubleshooting information for the HP 22-in-1 Media Card Reader is also included. Kit contents ● 3.5-inch media card reader with integrated USB cable ● HP Workstations adapter for 5.25-inch drive bays ● Four M3 guide screws ● Documentation CD ● Warranty - HP Z400 | HP 22-in-1 Media Card Reader Installation - Page 2
Guide. It describes proper computer setup, posture, health, and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located at http://www.hp of the computer. Before beginning the computer, observe HP accessories are for use in HP computer - HP Z400 | HP 22-in-1 Media Card Reader Installation - Page 3
5.25-inch bay adapter To install the 3.5-inch media card reader into a 5.25-inch drive bay, you must first install the reader into the 5.25-inch bay adapter. 1. If installing the media reader in an HP Z200 or Z400 Workstation, install four black M3 guide screws in the four lower holes of the bay - HP Z400 | HP 22-in-1 Media Card Reader Installation - Page 4
service guide for your computer at http://www.hp.com/support/ manuals. 2. Power down the computer, and then disconnect the power cord. 3. Power down all external devices, and then disconnect them from the computer. 4. Remove the side access panel. Removing components 1. If present, remove the card - HP Z400 | HP 22-in-1 Media Card Reader Installation - Page 5
Installing the media card reader in the computer 1. Install the media card reader into an optical drive bay. 2. Ensure that the adapter snaps securely into place. Figure 4 Installing the media card reader in the optical bay Connecting the media card reader NOTE: See the service label on the side - HP Z400 | HP 22-in-1 Media Card Reader Installation - Page 6
Reassembling the computer To reassemble the computer after installation: 1. Reinstall the card support, if removed. 2. Reinstall the airflow guide, if removed. 3. Reinstall the side access panel. 4. Reconnect power to the computer and all external devices. 5. Restore power to the computer and all - HP Z400 | HP 22-in-1 Media Card Reader Installation - Page 7
cards For a list of supported USB media cards for the HP 22-in-1 (USB) Media Card Reader, see the "Compatible Media Cards" document available on the CD included with this kit. NOTE: The HP 22-in-1 (USB) Media Card Reader is not compatible with 1394 devices. Troubleshooting Solving common problems - HP Z400 | HP 22-in-1 Media Card Reader Installation - Page 8
multivendor knowledge base, monitoring, and diagnostic tools, go to http://www.hp.com/support. To contact HP customer service worldwide, see http://www.hp.com/go/contacthp. Japanese 日本語 This document is available in Japanese. See http://www.hp.com/support/manuals, then select your product and select
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
HP 22-in-1 Media Card Reader
Introduction
This document describes how to install the HP 22-in-1 Media Card Reader into an HP Workstations
adapter bracket, and then install the media card reader and bracket into an HP computer. Basic
troubleshooting information for the HP 22-in-1 Media Card Reader is also included.
Kit contents
●
3.5-inch media card reader with integrated USB cable
●
HP Workstations adapter for 5.25-inch drive bays
●
Four M3 guide screws
●
Documentation CD
●
Warranty information
© 2009, 2010 Hewlett-Packard Development Company, L.P.
Microsoft, Windows, and Windows Vista are either trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other countries.
ENWW
Introduction
1