HP d240 HP Compaq d240/d248 Series Personal Computer, Service Reference Card
HP d240 - Microtower Desktop PC Manual
 |
View all HP d240 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP d240 manual content summary:
- HP d240 | HP Compaq d240/d248 Series Personal Computer, Service Reference Card - Page 1
Service Reference Card HP Compaq d240/d248 Series Personal Computers © 2003 Hewlett-Packard Development Company, L.P. The informa- tion contained herein is subject to change without notice. HP shall not be liable for technical or editorial errors or omissions contained herein. Intel, Pentium, - HP d240 | HP Compaq d240/d248 Series Personal Computer, Service Reference Card - Page 2
the instructions on problems installed on some models and can be downloaded free of charge from www.hp.com. Error Conditions and Messages Chassis Diagnostic LEDs Power RAM (S4) Suspend to disk (S5) Computer off Processor thermal shutdown Memory not seated / installed for system configuration in POST
-
1 -
2
 |
 |
Service Reference Card
HP Compaq d240/d248 Series
Personal Computers
©
2003 Hewlett-Packard Development Company, L.P. The informa-
tion contained herein is subject to change without notice. HP shall
not be liable for technical or editorial errors or omissions contained
herein. Intel, Pentium, Intel Inside, and the Intel logo are trademarks
or registered trademarks of the Intel Corporation and its subsidiaries
in the U. S. and other countries.
Product of the United States.
Document Number 355870-001.
1st Edition December 2003.
Key Specifications
System Setup and Boot
Basic system information regarding system information, setup, power management, hardware,
and passwords is maintained in the Setup Utility held in the system ROM. The Setup Utility is
accessed by pressing the F10 key when prompted (on screen) to do so during the boot sequence.
If the screen prompt opportunity is missed, a restart will be necessary.
Processor Type:
Intel Celeron or Pentium 4
RAM Type:
DDR PC2100, PC2700, or PC3200 non-ECC
Maximum RAM Supported:
4 GB
Expansion Bus:
PCI 2.2
Graphics Adapter
Integrated controller. AGP support on select models.
Hard drive interface:
UATA/100
I/O Interfaces:
Serial (1), parallel (1), USB 2.0 (8), diskette drive (1)
Computer Setup Menu
Heading
Option / Description
System
Information
Lists the following main system specifications:
•
Product Name
•
Chipset type
•
BIOS Version
•
BIOS Release Date
•
Processor Type
•
Processor Speed
•
CPU ID
•
L1 and L2 Cache Size
•
Memory Information
•
FSB Speed
•
Ratio Status
•
Ratio CMOS Setting
•
DDR Frequency
•
MAC Address
Standard
CMOS
Setup
System Time (hh/mm/ss) - Allows you to set system time. (24 hour for-
mat)
System Date (mm/dd/yyyy) - Allows you to set system date.
Floppy Drive A - Calculates size and capacity of diskette drive.
Primary IDE Master - Auto detects which hard drive is the Primary
Master drive.
Primary IDE Slave - Auto detects which hard drive is the Primary Slave
drive.
Secondary IDE Master - Auto detects which hard drive is the Secondary
Master drive.
Secondary IDE Slave - Auto detects which hard drive is the Secondary
Slave drive.
Advanced
CMOS
Setup
Boot Device
Priority
Specifies the boot order for all devices.
POST Delay
Time (sec-
onds)
Sets the amount of time before the Setup Utility prompt
(F10-Setup) appears when the computer boots.
•
None: POST delay time disable (Default)
•
5: POST Delay 5 seconds
•
15: POST Delay 15 seconds
•
25: POST Delay 25 seconds
•
35: POST Delay 35 seconds
System Key-
board
Detects if a keyboard is present when the computer
boots.
•
Absent: keyboard not detected (default)
•
Present: keyboard detected
APIC ACPI
SCI IRQ
Enables or disables the internal I/O APIC and Multipro-
cessor Tables. (Disabling the APIC ACPI SCI IRQ may
require you to reinstall the operating system.)
•
Enable: IRQ 20-23 (Default)
•
Disable: IRQ 01-11
Hyper-
Threading
Technology
Enables or disables the Intel Hyper-Threading Technol-
ogy. (This item is only selectable with the Intel HHT
CPU plug-in.)
•
Enable: Intel HTT function enabled (BIOS auto
detect)
•
Disable: Intel HTT function disabled (BIOS auto
detect)
Internal
Graphic
Mode Select
Selects the size of memory for internal graphic adapter.
•
Disable: Internal graphic memory mode select dis-
able
•
1MB: Share 1MB
•
4MB: Share 4MB
•
8MB: Share 8MB (Default)
•
16MB: Share 16 MB
•
32MB: Share 32 MB
Power Man-
agement
Setup
ACPI
Standby
State
Sets the ACPI Standby State when system goes into
ACPI Standby Mode.
•
S1/POS: Power on Suspend
•
S3/STR: Suspend to RAM (Default)
Computer Setup Menu
(Continued)
Heading
Option / Description
Power Man-
agement
Setup
(Continued)
Reset on AC/
Power Loss
Sets the system status after AC power loss.
•
Power Off: System always Powers Off (Default)
•
Power On: System always Powers On
•
Last State: System returns to the last state before AC
power loss
Resume on
Ring
Sets the Resume on Ring from soft off.
•
Disable: Ring Resume disable (Default)
•
Enable: Ring Resume enable
Resume on
PME
Sets the Resume on PME from soft off.
•
Disable: PME Resume disable
•
Enable: PME Resume enable (Default)
Peripheral
Setup
OnBoard
LAN
Enables or disables the OnBoard LAN.
•
Disable: OnBoard LAN disabled
•
Enable: OnBoard LAN enabled (Default)
OnBoard
LAN Chip
Boot ROM
Enables or disables the OnBoard LAN Chip Boot ROM.
•
Disable: OnBoard LAN Chip Boot ROM disabled
•
Enable: OnBoard LAN Chip Boot ROM enabled
(Default)
Init. Graph-
ics Adapter
Priority
Sets the initial priority of the graphics adapter
NR146 GV (d240/d248)
•
PCI/Int-VGA (Default)
•
Int-VGA/PCI
USB
Controller
Enables or disables the USB Controller.
•
Disable: USB Controller disabled
•
Enable: USB Controller enabled (Default)
USB 1.1
Device
Legacy
Support
Sets the USB 1.1 Device Legacy Support under DOS
Mode.
•
Disable: USB 1.1 Device Legacy Support disabled
•
All Device: All devices are supported
OnBoard
Serial Port
Sets the OnBoard Serial Port settings
•
Auto (Default)
•
Disable
•
3F8/COM1
•
2F8/COM2
•
3E8/COM3
•
2E8/COM4
OnBoard
Parallel Port
Sets the OnBoard Parallel Port settings
•
Auto (Default)
•
Disable
•
378
•
278
Hardware
Monitor
CPU
Warning
Temperature
Warns when CPU temperature exceeds 85°/185°F.
CPU
Shutdown
Temperature
System will shutdown when CPU temperature is greater
than 90°/194°F.
System
Warning
Temperature
Warns when system temperature is greater than 60°C/
140°F.
System
Shutdown
Temperature
System will shutdown when system temperature is
greater than 65°C/149°F.
CPU
Temperature
Detects current CPU temperature
System
Temperature
Detects current system temperature
CPU FAN
Speed
Detects CPU FAN speed
Chassis FAN
Speed
Detects current chassis FAN speed
CPU VID
Detects current CPU voltage
Vccp
Detects current Vccp voltage
+1.5V
Detects current ATX power +1.5V
+2.5V
Detects current ATX power +2.5V
+3.3V
Detects current ATX power +3.3V
+5.0V
Detects current ATX power +5.0V
+12.0V
Detects current ATX power +12.0V
HVcc
(+3.3VSB)
Detects HVcc voltage
Password
Option
Change
Supervisor
Password
Allows you to set and change the supervisor password
Password
Status
Shows password status
Password
Check
Allows you to set the password check when the supervi-
sor password is set up
•
Setup: Password prompt appears when BIOS is exe-
cuted
•
Always: Password verification is checked every time
the computer boots (Default)
Load default
Settings
None
Loads the optimum default values for all of the setup
options.
Save Set-
tings and
Exit
None
Exit system with new changes.
Exit With-
out Saving
None
Exit system setup without saving the changes.