Hikvision DS-2CD2063G0-I User Manual

Hikvision DS-2CD2063G0-I Manual

Get Hikvision DS-2CD2063G0-I PDF manuals and user guides View all Hikvision DS-2CD2063G0-I manuals
Add to My Manuals
Save this manual to your list of manuals

Hikvision DS-2CD2063G0-I manual content summary:

  • Hikvision DS-2CD2063G0-I | User Manual - Page 1
    Network Camera User Manual Network Camera User Manual UD09650B 0
  • Hikvision DS-2CD2063G0-I | User Manual - Page 2
    written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual This Manual is applicable to Network Camera. The Manual includes instructions for using and managing
  • Hikvision DS-2CD2063G0-I | User Manual - Page 3
    OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION to set up camera time manually. Visit the camera and enter system setting interface for time setting. Safety Instruction These instructions are intended to
  • Hikvision DS-2CD2063G0-I | User Manual - Page 4
    Camera User Manual support more than 50(N) Newton gravities if the camera is fixed to the ceiling.  If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems
  • Hikvision DS-2CD2063G0-I | User Manual - Page 5
    .  Improper use or replacement of the battery may result in hazard of explosion. Please use the manufacturer recommended battery type. Notes: For the camera supports IR, you are required to pay attention to the following precautions to prevent IR reflection:  Dust or grease on the dome cover will
  • Hikvision DS-2CD2063G0-I | User Manual - Page 6
    Network Camera User Manual body so that the foam ring and the dome cover are attached seamlessly. 5
  • Hikvision DS-2CD2063G0-I | User Manual - Page 7
    Network Camera User Manual Table of Contents Chapter 1 System Requirement 10 Chapter 2 Network Connection 11 Setting the Network Camera over the LAN 11 Wiring over the LAN...11 Activating the Camera ...12 (Optional) Setting Security Question 19 Setting the Network Camera over the WAN 19 Static
  • Hikvision DS-2CD2063G0-I | User Manual - Page 8
    Network Camera User Manual Maintenance 51 Upgrade & Maintenance 51 Log ...52 System Service ...53 Security Settings 54 Authentication ...54 IP Address Filter ...55 Security Service...56 User Management 57 User Management ...57 Security Question ...59 Online Users...60 Chapter 7 Network Settings
  • Hikvision DS-2CD2063G0-I | User Manual - Page 9
    Network Camera User Manual Configuring Display Settings 95 Day/Night Auto-Switch 95 Day/Night Scheduled-Switch 99 Configuring OSD Settings 100 Configuring Privacy Mask 102 Configuring Picture Overlay
  • Hikvision DS-2CD2063G0-I | User Manual - Page 10
    Network Camera User Manual Chapter 12 Playback 169 Chapter 13 Picture 171 Chapter 14 Application 172 Face Capture Statistics 172 People Counting Statistics 172 Heat Map Statistics 173 Counting
  • Hikvision DS-2CD2063G0-I | User Manual - Page 11
    Network Camera User Manual Chapter 1 System Requirement Operating System Microsoft Windows XP SP1 and above version CPU 2.0 GHz or higher RAM 1G or higher Display 1024×768 resolution or
  • Hikvision DS-2CD2063G0-I | User Manual - Page 12
    Network Camera User Manual Chapter 2 Network Connection Note:  You shall acknowledge that the contact with your dealer or the nearest service center.  To ensure the network security of the network camera, we recommend you to have the network camera assessed and maintained termly. You can contact
  • Hikvision DS-2CD2063G0-I | User Manual - Page 13
    Network Camera User Manual computer with a network cable as shown in Figure 2-1.  Refer to the Figure 2-2 to set network camera over the Activation via Client Software are all supported.  Activation via Web Browser Steps: 1. Power on the camera, and connect the camera to the network. 2. Input the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 14
    Network Camera User Manual to search the IP address. Activation via Web Browser 3. Create and Activation via SADP Software SADP software is used for detecting the online device, activating the camera, and resetting the password. Get the SADP software from the supplied disk or the official website,
  • Hikvision DS-2CD2063G0-I | User Manual - Page 15
    Note: The SADP software supports activating the camera in batch. Refer to the user manual of SADP software for reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. Note: You can enable the Hik-Connect service
  • Hikvision DS-2CD2063G0-I | User Manual - Page 16
    IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.  Activation via Client Software to the prompts. Follow the steps to activate the camera. Steps: 1. Run the client software and the control panel of the software pops up,
  • Hikvision DS-2CD2063G0-I | User Manual - Page 17
    the figure below. Network Camera User Manual Control Panel 2. Click the Device Management icon to enter the Device Management interface, as shown in the figure below. 16
  • Hikvision DS-2CD2063G0-I | User Manual - Page 18
    Network Camera User Manual Device Management Interface 3. Check the device status from the device to increase the security of your product. We recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product
  • Hikvision DS-2CD2063G0-I | User Manual - Page 19
    Network Camera User Manual Activation Interface (Client Software) 6. Click OK button to start activation. 7. Click to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. 9. Input the password to activate your IP address modification.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 20
    Network Camera User Manual (Optional) Setting Security Question Security question is used to reset the admin password when admin user forgets the password. Admin user can follow the pop-up window to complete security question settings during camera activation. Or, admin user can go to User
  • Hikvision DS-2CD2063G0-I | User Manual - Page 21
    Network Camera User Manual 5. Visit the network camera through a web browser or the client software over the internet. Accessing the Camera through Router with Static IP  Connecting the network camera with static IP directly You can also save the static IP in the camera and directly connect it to
  • Hikvision DS-2CD2063G0-I | User Manual - Page 22
    7. Visit the camera via the applied domain name.  Connecting the network camera via a modem Purpose: This camera supports the PPPoE auto dial-up function. The camera gets a public IP name resolution to solve the problem.  Normal Domain Name Resolution Steps: Normal Domain Name Resolution 21
  • Hikvision DS-2CD2063G0-I | User Manual - Page 23
    Network Camera User Manual 1. Apply a domain name from a domain name provider. 2. Configure the DDNS settings in the DDNS Settings interface of the network camera. Refer to Section 7.1.2 Configuring DDNS Settings for detailed configuration. 3. Visit the camera via the applied domain name. 22
  • Hikvision DS-2CD2063G0-I | User Manual - Page 24
    Network Camera User Manual Chapter 3 Access to the Network Camera Accessing by Web Browsers Note: For certain camera models, HTTPS is enabled by default and the camera creates an unsigned certificate automatically. When you access to the camera the first time, the web browser prompts a notification
  • Hikvision DS-2CD2063G0-I | User Manual - Page 25
    Network Camera User Manual 4. Click Login. 5. (Optional) Install the plug-in before viewing the live video and operating the camera. Follow the iVMS-4200 client software. You can view the live video and manage the camera with the software. Follow the installation prompts to install the software. The
  • Hikvision DS-2CD2063G0-I | User Manual - Page 26
    Network Camera User Manual iVMS-4200 Main View 25
  • Hikvision DS-2CD2063G0-I | User Manual - Page 27
    for the actual surveillance application. Note: This chapter is only applicable for the cameras with the built-in Wi-Fi module. Configuring Wi-Fi Connection in Manage and Ad-hoc Modes Purpose: Two connection modes are supported. Choose a mode as desired and perform the steps to configure the Wi-Fi
  • Hikvision DS-2CD2063G0-I | User Manual - Page 28
    Camera User Manual 3. Click to choose a wireless connection on the list. Wi-Fi Setting- Manage Mode 4. Check the radio button to select the Network mode as Manage, and the Security mode of the network is automatically shown when you select the wireless network, please don't change it manually
  • Hikvision DS-2CD2063G0-I | User Manual - Page 29
    Network Camera User Manual 2. Customize a SSID for the camera. 3. Choose the Security Mode of the wireless connection. 4. Enable the wireless connection function for your PC. 5. On the PC side, search the network and you can see the SSID of the camera listed. Ad-hoc Connection Point 6. Choose the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 30
    Network Camera User Manual WEP Mode  Authentication - Select Open or Shared Key System types available depend on the access point being used. The following options are available: HEX - Allows you to manually enter the hex key. ASCII - In this method the string must be exactly 5 characters for 64-bit
  • Hikvision DS-2CD2063G0-I | User Manual - Page 31
    Network Camera User Manual Choose the type of client/server authentication being used by the access point; EAP-TLS or EAP-PEAP. EAP-TLS EAP-TLS  Identity - Enter the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 32
    Network Camera User Manual strongly recommend the use of strong passwords for all functions and network devices. The password should be something of your own choosing (using a minimum of 8
  • Hikvision DS-2CD2063G0-I | User Manual - Page 33
    Camera User Manual of to enable WPS. 2. Choose the connection mode as PBC. Note: Support of this mode is mandatory for both the Access Points and the connecting devices guide of the router. 4. Push the WPS button to enable the function on the camera. If there is not a WPS button on the camera,
  • Hikvision DS-2CD2063G0-I | User Manual - Page 34
    Network Camera User Manual Use PIN Code If the PIN code is generated from the router side, you should enter the PIN code you get from the router side in the Router PIN code field. 3. Click Connect. Or You can generate the PIN code on the camera side. And the expired time for the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 35
    Network Camera User Manual Setting WLAN Parameters 3. Customize the IPv4 address, the IPv4 Subnet Mask and the Default Gateway. The setting procedure is the same with that of LAN. If you want to be assigned the IP address you can check the checkbox to enable the DHCP. 34
  • Hikvision DS-2CD2063G0-I | User Manual - Page 36
    Network Camera User Manual Chapter 5 Live View Live View Page Purpose: The live view page allows you to view the real-time video, capture images, realize PTZ control, set/call presets and configure video parameters. Log in the network camera to enter the live view page, or you can click Live View on
  • Hikvision DS-2CD2063G0-I | User Manual - Page 37
    . The window size is 4:3. The window size is 16:9. The original widow size. Self-adaptive window size. Live view with the different video streams. , etc. Supported video streams vary according to camera models. Click to select the third-party plug-in. Manually capture the picture. 36
  • Hikvision DS-2CD2063G0-I | User Manual - Page 38
    Note: The icons vary according to the different camera models. Recording and Capturing Pictures Manually In the live view interface, click on the camera. Note: To realize PTZ control, the camera connected to the network must support the PTZ function or have a pan/tilt unit installed to the camera
  • Hikvision DS-2CD2063G0-I | User Manual - Page 39
    Network Camera User Manual PTZ Control Panel Click the zoom/focus/iris buttons to realize lens control. Notes:  There are eight direction arrows in the control panel. Click the arrows to realize adjustment in the relative positions.  For the cameras which support lens movements only, the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 40
    3. Click to finish the setting of the current preset. 4. You can click to delete the preset.  Calling a Preset: This feature enables the camera to point to a specified preset scene manually or when an event takes place. For the defined preset, you can call it at any time to the desired preset scene
  • Hikvision DS-2CD2063G0-I | User Manual - Page 41
    Network Camera User Manual Calling a Preset Setting/Calling a Patrol Note: No less than 2 presets have to be configured before you set a patrol. Steps: 1. Click to enter the patrol configuration
  • Hikvision DS-2CD2063G0-I | User Manual - Page 42
    Network Camera User Manual Chapter 6 Network Camera Configuration Configuring Local Parameters Purpose: The local configuration refers to the parameters of the live view, record files and captured pictures. The record files and
  • Hikvision DS-2CD2063G0-I | User Manual - Page 43
    Network Camera User Manual TCP: Ensures complete delivery of streaming data and better record files you recorded with the web browser.  Record File Size: Select the packed size of the manually recorded and downloaded video files to 256M, 512M or 1G. After the selection, the maximum record file size
  • Hikvision DS-2CD2063G0-I | User Manual - Page 44
    Camera User Manual  Picture and Clip Settings: Set the saving paths of the captured pictures and clipped video files. Valid for the pictures you capture with the web browser.  Save snapshots in live view to: Set the saving path of the manually instructions camera, such as Model, Serial No., Firmware
  • Hikvision DS-2CD2063G0-I | User Manual - Page 45
    User Manual the firmware for the camera. Online Upgrade Note: When the camera is upgrading, don't power off the camera. During upgrading, the camera may not be accessible. You need to wait 1 or 2 minutes before the upgrade finishes. Configuring Time Settings Purpose: You can follow the instructions
  • Hikvision DS-2CD2063G0-I | User Manual - Page 46
    Network Camera User Manual 3. Configure the NTP settings. (1) Click to enable the NTP function. to test the time synchronization function via NTP server. Time Sync by NTP Server Note: If the camera is connected to a public network, you should use a NTP server that has a time synchronization function
  • Hikvision DS-2CD2063G0-I | User Manual - Page 47
    Network Camera User Manual Time Sync Manually  Click Save to save the settings. Configuring RS232 Settings The RS232 port can be used in two ways:  Parameters Configuration: Connect a computer to the camera through the serial port. Device parameters can be configured by using software such as
  • Hikvision DS-2CD2063G0-I | User Manual - Page 48
    Network Camera User Manual RS232 Settings Note: If you want to connect the camera by the RS232 port, the parameters RS485 Settings Purpose: The RS485 serial port is used to control the PTZ of the camera. The configuring of the PTZ parameters should be done before you control the PTZ unit.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 49
    Network Camera User Manual RS-485 Settings 2. Set the RS485 parameters and click Save to Note: The Baud Rate, PTZ Protocol and PTZ Address parameters should be exactly the same as the PTZ camera parameters. Configuring DST Settings Purpose: Daylight Saving Time (DST) is a way of making better use of
  • Hikvision DS-2CD2063G0-I | User Manual - Page 50
    Network Camera User Manual DST Settings 2. Select the start time and the end time. 3. Select the DST Bias. 4. Click Save to activate the settings. Configuring External Devices Purpose: For the device supported external devices, including the wiper on the housing or the LED light, you can control
  • Hikvision DS-2CD2063G0-I | User Manual - Page 51
    Network Camera User Manual the Start Time and End Time. Set Schedule  Auto: The LED will be > VCA Resource 2. Select a desired VCA combination. Available VCA combination varies according to different camera models. 3. Click Save to save the settings. A reboot is required after setting the VCA
  • Hikvision DS-2CD2063G0-I | User Manual - Page 52
    Camera User Manual the others are hidden. • The function may not be supported by some camera models. Open Source Software License Information about the open source software that applies to the IP camera  Reboot: Restart the device.  Restore: Reset all the parameters, except the IP parameters and
  • Hikvision DS-2CD2063G0-I | User Manual - Page 53
    password to start importing configuration file. Note: You need to reboot the camera after importing configuration file.  Upgrade: Upgrade the device to a certain version. Steps: 1. Select firmware or firmware directory to locate the upgrade file. Firmware: Locate the exact path of the upgrade file
  • Hikvision DS-2CD2063G0-I | User Manual - Page 54
    Network Camera User Manual Log Searching Interface 2. Set the log search conditions to log files. System Service Purpose: System service settings refer to the hardware service the camera supports. Supported functions vary according to the different cameras. For the cameras support IR Light, 53
  • Hikvision DS-2CD2063G0-I | User Manual - Page 55
    Network Camera User Manual ABF (Auto Back Focus), Auto Defog, or Status LED, you can select to enable or disable the corresponding service according to the , including Authentication, IP Address Filter, and Security Service from security interface. Authentication Purpose: You can specifically
  • Hikvision DS-2CD2063G0-I | User Manual - Page 56
    Network Camera User Manual Digest is the recommended authentication method for better data security. You must be aware of the risk if you adopt basic as the authentication method. 3.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 57
    Network Camera User Manual Add an IP (3) Click the OK to finish adding.  Modify an IP Security Service To enable the remote login, and improve the data communication security, the camera provides the security service for better user experience. Steps: 1. Enter the security service configuration
  • Hikvision DS-2CD2063G0-I | User Manual - Page 58
    Network Camera User Manual Security Service 2. Check the checkbox of Enable Illegal Login Lock. Illegal Login Lock: it is used to limit the user login attempts. Login attempt from the IP
  • Hikvision DS-2CD2063G0-I | User Manual - Page 59
    Network Camera User Manual accounts. The admin user cannot be deleted and you can only change increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 60
    Network Camera User Manual 4. Click OK to finish the user modification.  Deleting a User Steps: and input answers. 5. Click OK to save the settings. Reset Admin Password: Before you start: The PC used to reset password and the camera should belong to the same IP address segment of the same
  • Hikvision DS-2CD2063G0-I | User Manual - Page 61
    Network Camera User Manual 2. Click Forget Password. 3. Answer security question. 4. Create new password. Note: User IP address is locked for 30 minutes after 7 failed attempts of answering security questions.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 62
    IP, DDNS, PPPoE, Port, and NAT, etc., by following the instructions in this section. Configuring TCP/IP Settings Purpose: TCP/IP settings must be properly configured before you operate the camera over network. The camera supports both the IPv4 and IPv6. Both versions can be configured simultaneously
  • Hikvision DS-2CD2063G0-I | User Manual - Page 63
    Network Camera User Manual TCP/IP Settings 2. Configure the basic network settings, including the NIC Type, IPv4 or IPv6 Address, IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default
  • Hikvision DS-2CD2063G0-I | User Manual - Page 64
    Camera User Manual multicast group address. Before utilizing this function, you have to enable the Multicast function of your router.  A reboot is required for the settings to take effect. Configuring DDNS Settings Purpose: If your camera the DDNS settings of the camera. Steps: 1. Enter the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 65
    Camera User Manual Figure 7-2 DynDNS Settings  NO-IP: Steps: (1)Choose the DDNS Type as NO-IP. Figure 7-3 NO-IP DNS Settings (2) Enter the Server Address as www.noip.com (3) Enter the Domain name you registered. (4) Enter the User Name and Password. (5) Click Save and then you can view the camera
  • Hikvision DS-2CD2063G0-I | User Manual - Page 66
    Network Camera User Manual Configuring PPPoE Settings Steps: 1. Enter the PPPoE Settings interface: Configuration > Network > Basic Settings > PPPoE PPPoE Settings 2. Check the Enable PPPoE checkbox to enable this feature. 3.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 67
    Network Camera User Manual You can set the port No. of the camera, e.g., HTTP port, RTSP port and HTTPS port. Steps: 1. Enter the Port Settings interface, Configuration > Network > Basic Settings > Port Port Settings 2. Set the ports of the camera. HTTP Port: The default port number is 80, and it
  • Hikvision DS-2CD2063G0-I | User Manual - Page 68
    Network Camera User Manual Note: WebSocket and WebSockets protocol are used for plug-in free live view. With the function enabled, you don't need to configure the port mapping for each port, and the camera is connected to the Wide Area Network via the router. UPnP Settings Steps: 1. Enter the NAT
  • Hikvision DS-2CD2063G0-I | User Manual - Page 69
    manually. 5. Click Save to save the settings. Configure Advanced Settings Purpose: You can configure the parameters, including SNMP, FTP, Email, HTTPS, QoS, 802.1x, etc., by following the instructions in this section. Configuring SNMP Settings Purpose: You can set the SNMP function to get camera
  • Hikvision DS-2CD2063G0-I | User Manual - Page 70
    Network Camera User Manual strongly recommend the use of strong passwords for all functions and network devices. The password should be something of your own choosing (using a minimum of 8
  • Hikvision DS-2CD2063G0-I | User Manual - Page 71
    Network Camera User Manual SNMP Settings 2. Check the checkbox of Enable SNMPv1, Enable SNMP v2c, Enable SNMPv3 to enable the feature correspondingly. 3. Configure the SNMP settings. Note: The settings of the SNMP software should be the same as the settings you 70
  • Hikvision DS-2CD2063G0-I | User Manual - Page 72
    Network Camera User Manual configure here. 4. Click Save to save and finish the settings. Notes: • A reboot is required for the settings to take effect. • To lower the risk of
  • Hikvision DS-2CD2063G0-I | User Manual - Page 73
    FTP server login. Network Camera User Manual  For your privacy and to better protect your the name of the directory; and when the Child Directory is selected, you can use the Camera Name or Camera No. as the name of the directory. Picture Filing Interval: For better picture management, you can
  • Hikvision DS-2CD2063G0-I | User Manual - Page 74
    Network Camera User Manual anonymous access to the FTP server. Note: The anonymous access function must be supported by the FTP server. 6. Click Save to save the settings. 7.2.3 Configuring Email Settings Purpose: The system can be configured to send an Email notification to
  • Hikvision DS-2CD2063G0-I | User Manual - Page 75
    Network Camera User Manual The SMTP port should be set as 465 for this encryption you want to use STARTTLS, make sure that the protocol is supported by your e-mail server. If you check the Enable STARTTLS checkbox when the protocol is not supported by your e-mail sever, your e-mail will not be
  • Hikvision DS-2CD2063G0-I | User Manual - Page 76
    Network Camera User Manual 4. Click Save to save the settings. Email Settings Platform Access Purpose: Platform the platform access function of the device. 3. Select the Platform Access Mode. Note: Hik-Connect is an application for mobile devices. With the App, you can view live image of the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 77
    Camera User Manual If you select Platform Access Mode as Hik-Connect, 1) Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 2) Create a verification code or change the verification code for the camera. Note: • The verification code is required when you add the camera to Hik
  • Hikvision DS-2CD2063G0-I | User Manual - Page 78
    Network Camera User Manual 2. Check the checkbox to enable the wireless dial settings. 3. Configure the dial parameters. 1) Select the dial mode from the drop-down list. Auto and Manual are selectable. If Auto is selected, you can set the arming schedule for dialing; If Manual is selected, you can
  • Hikvision DS-2CD2063G0-I | User Manual - Page 79
    Network Camera User Manual 4) (Optional) You can click Send Test SMS to send a message to the the-middle attacks. Note:  HTTPS is enabled by default for certain camera models.  If HTTPS is enabled, the camera creates an unsigned certificate automatically. When accessing via HTTPS, the web browser
  • Hikvision DS-2CD2063G0-I | User Manual - Page 80
    Network Camera User Manual Create Self-signed Certificate  Create the self-signed certificate (1) Select Create Self-signed Certificate as the Installation Method. (2) Click Create button to enter the creation
  • Hikvision DS-2CD2063G0-I | User Manual - Page 81
    Network Camera User Manual Import the Certificate (1) b) Select Create the certificate request first and continue the installation. Click Browse and Install to import the certificate to the device. Import
  • Hikvision DS-2CD2063G0-I | User Manual - Page 82
    Network Camera User Manual QoS (Quality of Service) can help solve the network delay and network congestion 802.1X standard is supported by the network cameras, and when the feature is enabled, the camera data is secured and user authentication is needed when connecting the camera to the network
  • Hikvision DS-2CD2063G0-I | User Manual - Page 83
    Network Camera User Manual  For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network
  • Hikvision DS-2CD2063G0-I | User Manual - Page 84
    Network Camera User Manual Integration Protocol Purpose: If you need to access to the camera through the third party media user, operator, and administrator. Note: ONVIF user account is different from the camera user account. You have set ONVIF user account independently. 3. Save the settings. Note
  • Hikvision DS-2CD2063G0-I | User Manual - Page 85
    Network Camera User Manual Network Service You can control the ON/OFF status of certain protocol that the camera supports. Note: • Keep unused function OFF for security concern. • The function is supported by certain camera model. WebSocket or WebSockets protocol are used for plug-in-free live view.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 86
    Network Camera User Manual Chapter 8Video/Audio Settings Purpose: Follow the instructions below to configure the video setting, audio settings, ROI, Display info. on Stream, etc. Configuring Video Settings For certain camera models, you can configure parameters for available video streams, for
  • Hikvision DS-2CD2063G0-I | User Manual - Page 87
    Network Camera User Manual Video Settings 2. Select the Stream Type. Supported stream types are listed in the drop-down list. Notes: • For some models, the Third Stream is not enabled by default. Go to System > Maintenance > System Service> Software to enable the function is required. • The main
  • Hikvision DS-2CD2063G0-I | User Manual - Page 88
    Network Camera User Manual When bitrate type is selected as Variable, 6 levels of video max. bitrate value varies according to different camera platforms. For certain cameras, the maximum limit is 8192 Kbps or 12288 Kbps. Video Encoding: The camera supports multiple video encodings types, such as H.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 89
    Network Camera User Manual H.265+ reduces storage by up to 50% with the same maximum bitrate in most scenes. You need to reboot the camera if you want to turn out. • With H.264+/H.265+ enabled, some functions are not supported. For those functions, corresponding interfaces will be hidden. • H.264
  • Hikvision DS-2CD2063G0-I | User Manual - Page 90
    Network Camera User Manual bandwidth is insufficient. Smoothing: It refers to the smoothness but cannot record or playback them. Notes: • Custom video function requires the support of the camera. • After a camera restore action (not restore to default setting), quantity of custom video streams and
  • Hikvision DS-2CD2063G0-I | User Manual - Page 91
    Network Camera User Manual Steps: Custom Video Settings 1. Click to add a stream. 2. Change the stream name if needed. Note: Up to 32 letters and symbols (except or ") are allowed
  • Hikvision DS-2CD2063G0-I | User Manual - Page 92
    Network Camera User Manual Audio Settings 2. Configure the following settings. Note: Audio settings vary according to different camera models. Audio Encoding: G.722.1, G.711 ulaw, G.711alaw, G.726, MP2L2 and PCM are selectable. For MP2L2, the Sampling Rate and Audio Stream Bitrate are configurable.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 93
    Network Camera User Manual Region of Interest Settings Steps: 1. Enter the ROI settings interface: Configuration > Video/Audio > ROI. 2. Select the Stream Type for ROI encoding. 3. Check the checkbox of
  • Hikvision DS-2CD2063G0-I | User Manual - Page 94
    Network Camera User Manual (3) Click Drawing. Click and drag the mouse on the view checkbox to enable Face Tracking. Note: To enable face tracking function, the face detection function should be supported and enabled. (2) Select the ROI level. 6. Click Save to save the settings. Note: ROI level
  • Hikvision DS-2CD2063G0-I | User Manual - Page 95
    Network Camera User Manual Configuring Target Cropping Purpose: You can specify a target area on details of the target area if needed. Note: Target cropping function varies according to different camera models. Steps: 1. Enter the Target Cropping settings interface. 2. Check Enable Target Cropping
  • Hikvision DS-2CD2063G0-I | User Manual - Page 96
    Network Camera User Manual Chapter 9 Image Settings Purpose: Follow the instructions in this chapter to configure the image parameters, in display settings. Note: The display parameters vary according to the different camera models. Please refer to the actual interface for details. Day/Night Auto-
  • Hikvision DS-2CD2063G0-I | User Manual - Page 97
    be amplified to a larger extent. Exposure Settings  Focus For camera support motor-driven lens, you can set the focus mode as Auto, Manual or Semi-auto. Auto: Camera focus is adjusted automatically according to the actual monitoring scenario. Manual: You can control the lens by adjusting the zoom
  • Hikvision DS-2CD2063G0-I | User Manual - Page 98
    Network Camera User Manual and auxiliary focus manually. Semi-Auto: Camera will focus automatically when you adjust the or night. Smart Supplement Light: Set the supplement light as ON, and Auto and Manual are selectable for light mode. Select Auto, and the supplement light changes according to the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 99
    Network Camera User Manual if the object is near the camera, the device adjusts the supplement light to lower power image quality.  White Balance White balance is the white rendition function of the camera used to adjust the color temperature according to the environment. White Balance  Image
  • Hikvision DS-2CD2063G0-I | User Manual - Page 100
    Network Camera User Manual and the image is misty. It enhances the subtle details so that may appear distorted to some extent. Turn on this function to correct the distortion.  Others Some camera models support CVBS, SDI, or HDMI output. Set the local output ON or OFF according to the actual device
  • Hikvision DS-2CD2063G0-I | User Manual - Page 101
    illumination. Network Camera User Manual Day/Night Scheduled-Switch Configuration Interface Steps: 1. Click the calendar icon to parameter is changed. Configuring OSD Settings Purpose: You can customize the camera name, time/date format, display mode, and OSD size displayed on the live view. 100
  • Hikvision DS-2CD2063G0-I | User Manual - Page 102
    Network Camera User Manual OSD Settings Steps: 1. Enter the OSD Settings interface: Configuration > Image > OSD Settings. 2. Check the corresponding checkbox to select the display of camera name, date or week if required. 3. Edit the camera name in the text field of Camera Name. 4. Select from the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 103
    Network Camera User Manual 8. Click Save to save the settings. Configuring Privacy Mask Purpose: Privacy mask enables you to cover certain areas on the live video to prevent certain
  • Hikvision DS-2CD2063G0-I | User Manual - Page 104
    Network Camera User Manual you set without saving them. 6. Click Save to save the settings. Configuring Picture Overlay Purpose: Picture overlay enables you to overlay a picture on the image.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 105
    128*128. Network Camera User Manual 104
  • Hikvision DS-2CD2063G0-I | User Manual - Page 106
    Network Camera User Manual Chapter 10 Event Settings This section explains how to configure the network camera to respond to alarm events, including basic event and smart event. Basic Events You can configure the basic events by following the instructions in this section, including motion detection,
  • Hikvision DS-2CD2063G0-I | User Manual - Page 107
    Network Camera User Manual 3. Check the checkbox of Enable Dynamic Analysis for Motion if you want to mark the detected objects with green rectangles. Note: Select Disable for rules
  • Hikvision DS-2CD2063G0-I | User Manual - Page 108
    Network Camera User Manual Task 2: Set the Arming Schedule for Motion Detection Arming Schedule Steps: 1. Click Arming Schedule to edit the arming schedule. 2. Click on the time bar and
  • Hikvision DS-2CD2063G0-I | User Manual - Page 109
    Network Camera User Manual save the settings. 4. Move the mouse to the end of each day, a Method Note: The linkage methods vary according to the different camera models.  Audible Warning Trigger the audible warning locally. And it only supported by the device that have the audio output.  Notify
  • Hikvision DS-2CD2063G0-I | User Manual - Page 110
    Network Camera User Manual complete Email setup in advance.  Upload to FTP/Memory Card/NAS Capture the image when an alarm is triggered and upload the picture to a FTP
  • Hikvision DS-2CD2063G0-I | User Manual - Page 111
    Network Camera User Manual Expert Mode of Motion Detection  Day/Night Switch OFF Steps: 1. Draw the detection area as in the normal configuration mode. Up to 8 areas are supported. 2. Select OFF for Switch Day and Night Settings. 3. Select the area by clicking the area No. 4. Slide the cursor to
  • Hikvision DS-2CD2063G0-I | User Manual - Page 112
    Network Camera User Manual 6. Set the arming schedule and linkage method as in the normal configuration mode. 7. Click Save to save the settings.  Day/Night Scheduled-Switch Steps: 1. Draw the detection area as in the normal configuration mode. Up to 8 areas are supported. 2. Select Scheduled-
  • Hikvision DS-2CD2063G0-I | User Manual - Page 113
    Network Camera User Manual 2. Check Enable Video Tampering checkbox to enable the video tampering detection. 3. Click Edit to edit the arming schedule for video tampering. The arming schedule configuration
  • Hikvision DS-2CD2063G0-I | User Manual - Page 114
    Network Camera User Manual Alarm Input Settings 3. Click Arming Schedule to set the arming schedule for the alarm input. Refer to Task 2: Set the Arming Schedule for Motion Detection
  • Hikvision DS-2CD2063G0-I | User Manual - Page 115
    Network Camera User Manual 10.1.4 Configuring Alarm Output Alarm Output Settings Steps: 1. Enter the Alarm 3. The Delay time can be set to 5sec, 10sec, 30sec, 1min, 2min, 5min, 10min or Manual. The delay time refers to the time duration that the alarm output remains in effect after alarm occurs. 4.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 116
    Camera User Manual 6. Click Save to save the settings. 10.1.5 Handling Exception The exception type can be HDD full, HDD error, network disconnected, IP address conflicted and illegal login to the cameras Other Alarm Note: Some certain cameras support Wireless Alarm, PIR (passive infrared
  • Hikvision DS-2CD2063G0-I | User Manual - Page 117
    Network Camera User Manual Configuration > Advanced Configuration> Basic Event> Wireless Alarm Setting Wireless Alarm 2. Select the wireless alarm number. Up to 8 channels of external wireless alarm input are supported. 3. Check the checkbox of Enable Wireless Alarm to activate the wireless alarm.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 118
    Network Camera User Manual A PIR (Passive Infrared) alarm is triggered when an intruder moves within the detector's field of view. The heat energy dissipated schedule. 6. Click Save to save the settings. 7. Go to Configuration > Advanced Configuration> System> Remote Control to arm the camera. 117
  • Hikvision DS-2CD2063G0-I | User Manual - Page 119
    Network Camera User Manual Figure 10-13 Arming PIR Alarm  Emergency Alarm Purpose: You can press the save the settings. Smart Events You can configure the smart events by following the instructions in this section, including audio exception detection, defocus detection, scene change detection, 118
  • Hikvision DS-2CD2063G0-I | User Manual - Page 120
    Network Camera User Manual intrusion detection, and line crossing detection, etc. These events can trigger the alarm is triggered. Note: Audio exception detection function varies according to different camera models. Steps: 1. Enter the Audio Exception Detection settings interface, Configuration >
  • Hikvision DS-2CD2063G0-I | User Manual - Page 121
    Network Camera User Manual the sound steep rise in the surveillance scene. You can set the be taken when the alarm is triggered. Note: Defocus detection function varies according to different camera models. Steps: 1. Enter the Defocus Detection settings interface, Configuration > Event > Smart Event >
  • Hikvision DS-2CD2063G0-I | User Manual - Page 122
    Network Camera User Manual Configuring Defocus Detection 2. Check the checkbox of Enable to enable the function. of surveillance environment affected by the external factors, such as the intentional rotation of the camera. Some certain actions can be taken when the alarm is triggered. Note: Scene
  • Hikvision DS-2CD2063G0-I | User Manual - Page 123
    Network Camera User Manual Scene Change Detection 2. Check the checkbox of Enable to enable the function. 3. Click-and-drag the slider to set the detection sensitivity. The sensitivity value
  • Hikvision DS-2CD2063G0-I | User Manual - Page 124
    Network Camera User Manual 1. Enter the Face Detection settings interface, Configuration > Event > Smart Event > Face Detection. 2. Check the Enable Face Detection checkbox to enable the function. 3. Check the checkbox
  • Hikvision DS-2CD2063G0-I | User Manual - Page 125
    Network Camera User Manual 7. Click Save to save the settings. Configuring Intrusion Detection Purpose: when the alarm is triggered. Note: Intrusion detection function varies according to different camera models. Steps: 1. Enter the Intrusion Detection settings interface, Configuration> Event >
  • Hikvision DS-2CD2063G0-I | User Manual - Page 126
    Network Camera User Manual 2. Check the checkbox of Enable to enable the function. 3. Select a region number from the drop-down list of only when 40 percent body part enters the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 125
  • Hikvision DS-2CD2063G0-I | User Manual - Page 127
    Network Camera User Manual 10. Repeat the above steps to configure other regions. Up to taken when the alarm is triggered. Note: Line crossing detection function varies according to different camera models. Steps: 1. Enter the Line Crossing Detection settings interface, Configuration > Event > Smart
  • Hikvision DS-2CD2063G0-I | User Manual - Page 128
    Network Camera User Manual Line Crossing Detection 2. Check the checkbox of Enable to enable the function. 3. Select the line from the drop-down list. 4. Click Area Settings tab and
  • Hikvision DS-2CD2063G0-I | User Manual - Page 129
    Network Camera User Manual Max. Size: The maximum size of a valid target. Targets with when 40 percent or more body part goes across the line. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 10. Repeat the above steps to configure other
  • Hikvision DS-2CD2063G0-I | User Manual - Page 130
    Network Camera User Manual Configuring Region Entrance Detection Purpose: Region entrance detection function detects people, vehicle or other objects which enter a pre-defined virtual region from the outside place,
  • Hikvision DS-2CD2063G0-I | User Manual - Page 131
    Network Camera User Manual 4. Click Area Settings and click Draw Area button to entrance action only when 40 percent body part enters the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 9. Repeat the above steps to configure other
  • Hikvision DS-2CD2063G0-I | User Manual - Page 132
    Network Camera User Manual from a pre-defined virtual region, and some certain actions can be taken when the alarm is triggered. Steps: 1. Enter the Region Exiting Detection settings interface,
  • Hikvision DS-2CD2063G0-I | User Manual - Page 133
    Network Camera User Manual not trigger detection. Min. Size: The minimum size of a valid action only when 40 percent body part exits the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 9. Repeat the above steps to configure other
  • Hikvision DS-2CD2063G0-I | User Manual - Page 134
    Network Camera User Manual Unattended Baggage Detection 2. Check Enable checkbox to enable the function. 3. Select the Region from the drop-down list for detection settings. 4. Click Area Settings and
  • Hikvision DS-2CD2063G0-I | User Manual - Page 135
    Network Camera User Manual Threshold: Range [5-100s], the threshold for the time of the when 40 percent body part of the target enters the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 10. Repeat the above steps to configure other
  • Hikvision DS-2CD2063G0-I | User Manual - Page 136
    Network Camera User Manual Object Removal Detection 2. Check Enable checkbox to enable the function. 3. Select the Region from the drop-down list for detection settings. 4. Click Area Settings and
  • Hikvision DS-2CD2063G0-I | User Manual - Page 137
    Network Camera User Manual disappears from the region for 10s. 9. Drag the slider to when 40 percent body part of the target leaves the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 10. Repeat the above steps to configure other
  • Hikvision DS-2CD2063G0-I | User Manual - Page 138
    Network Camera User Manual Behavior Analysis  Overlay & Capture Display information includes the display on picture and display on stream. Display VCA info. on Stream: The green frames will be
  • Hikvision DS-2CD2063G0-I | User Manual - Page 139
    as Input Basic Data or Draw on Live View Video. Input Basic Data: Input the mounting height, viewing angle, and horizon ratio of the camera manually. Draw on Live View Video: Click Draw Verification Line (Horizontal) / (Vertical) to draw a horizontal/vertical line in the live view, and input the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 140
    Network Camera User Manual 4. You can click to delete the drawn lines. 5. Click Save to save the settings.  Shield Region The shield region allows you to set the specific region in which the behavior analysis will not function. Up to 4 shield regions are supported. Steps: 1. Click Shield Region tab
  • Hikvision DS-2CD2063G0-I | User Manual - Page 141
    Network Camera User Manual Configure the Rule Filter type: Pixels and Actual Size are size is between the minimum value and maximum value will trigger the alarm. Note: Make sure the camera calibration is configured if actual size is selected. Detection Target: Select Human or Vehicle as the detection
  • Hikvision DS-2CD2063G0-I | User Manual - Page 142
    Network Camera User Manual to left click on the live video to set the end rules and 2 combined rules are configurable. And the line crossing, intrusion, region exiting and region entrance are supported for the combined rules. 6. Click Save to save the settings. 7. Click Arming Schedule tab to set the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 143
    Network Camera User Manual Advanced Configuration Detection Sensitivity [0~4]: Refers to the sensitivity of the camera detects a target. The higher the value, the easier a target be recognized, and the higher the misinformation is. The default value of 3 is recommended. Background Update
  • Hikvision DS-2CD2063G0-I | User Manual - Page 144
    Network Camera User Manual 1. Check the checkbox of Global Size Filter to enable the function. the target whose size is between the minimum value and maximum value will trigger the alarm. Notes: ● Camera calibration has to be configured if you select the filter by actual size. ● The length of the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 145
    Network Camera User Manual if in a live view or playback. Display Target info. on Alarm to set the specific region in which the face capture will not function. Up to 4 shield regions are supported. Steps: 1. Click the hexagons sign to draw shield area by left click end-points in the live view
  • Hikvision DS-2CD2063G0-I | User Manual - Page 146
    Network Camera User Manual 1. Check the checkbox of Rule to enable rules of face capture. live view window, and right click to finish the area drawing. Notes:  Polygon area (4~10 sides) sides is supported.  If the live view is stopped, there is no way to draw the configured area. 4. Click Save to
  • Hikvision DS-2CD2063G0-I | User Manual - Page 147
    default value is 1 minute. Note: If the face exposure is enabled, please make sure the WDR function is disabled, and the manual iris is selected. Enable Face ROI: If the camera captures a face, the face area will be treated as the region of interest, and the image quality of this area will
  • Hikvision DS-2CD2063G0-I | User Manual - Page 148
    Network Camera User Manual People Counting Purpose: People function is used to calculate the number of object entered or exited a certain configured area and it is widely applied to the entrances or exits. Notes: It is recommended to install the camera right above the entrance/exit. To improve the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 149
    Network Camera User Manual 3. Set the detection line. An orange line, named as detection line line to adjust its length. Note: • The detection line should be drawn at the position right below the camera, and it should cover the whole entrance/exit. • Don't draw the line at the place where people may
  • Hikvision DS-2CD2063G0-I | User Manual - Page 150
    Network Camera User Manual 3) Dragging the cursor or input a value to set the Real-Time Upload Data checkbox. 4) If you want manually set the counting cycle, select the desired time period from the Data Statistics Cycle dropdown list. 5) To reset the counter, click the button on the left of
  • Hikvision DS-2CD2063G0-I | User Manual - Page 151
    Network Camera User Manual Counting Counting function helps to calculate the number of people entered or exited a certain configured area and is widely applied to the entrances or exits. Compared with the people counting function supported by iDS camera, counting function needs no camera calibration
  • Hikvision DS-2CD2063G0-I | User Manual - Page 152
    Network Camera User Manual people entered and exited is displayed on the live video. 4. will appear on the image. Note: • The detection line should be drawn at the position right below the camera, and it should cover the whole entrance / exit. • Draw the detection line at the position don't have
  • Hikvision DS-2CD2063G0-I | User Manual - Page 153
    Network Camera User Manual Heat Map Configuration 2. Check Enable Heat Map checkbox to enable the parameters for drawn area. Detection Sensitivity [0~100]: It refers to the sensitivity of the camera identify a target. The over-high sensitivity may cause the misinformation. It is recommended you set
  • Hikvision DS-2CD2063G0-I | User Manual - Page 154
    Camera User Manual camera treats the cabinet (on which the good removed) as a new scene. The default value of 50 is recommended. Scene Change Level [0~100]: It refers to level of the camera responses to the dynamic environment, e.g., a swaying curtain. The camera size of the camera identify a target.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 155
    Network Camera User Manual Note: Road traffic function varies according to different camera models.  Detection Configuration Steps: 1. Select the to adjust the length and angle of the line. 5. Adjust the zoom ratio of the camera so that the size of the vehicle in the image is close to that of the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 156
    Network Camera User Manual • Upload to FTP/Memory Card/NAS: Capture the image when an alarm queue management, go to Application. Note: Queue management is only supported by certain camera models. Rule Settings The camera supports Regional People Queuing-Up and Waiting Time Detection. Check checkbox
  • Hikvision DS-2CD2063G0-I | User Manual - Page 157
    Network Camera User Manual is that his/her head and shoulder enter the region. Steps: i. Click Add Region. ii. (Optional) Select a color for a region from the color drop-down list. iii. Draw a region by right click to determine the region boundary. Up to 10 edges are supported for a region. Move the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 158
    Network Camera User Manual Alarm Interval: In the set alarm interval, alarms of the alarm is triggered. c) Repeat above steps to set up other regions if needed. Up to 3 regions are supported. 2. Arming Schedule. Set the arming schedule for the function. In the armed periods, the function is active.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 159
    storage device configured. Configuring Record Schedule Purpose: There are two kinds of recording for the cameras: manual recording and scheduled recording. In this section, you can follow the instructions to configure the scheduled recording. By default, the record files of scheduled recording are
  • Hikvision DS-2CD2063G0-I | User Manual - Page 160
    Network Camera User Manual Record Parameters  Pre-record: The time you set to start recording before the scheduled time or the event. For example, if an alarm triggers recording at 10:00, and the pre-record time is set as 5 seconds, the camera starts to record at 9:59:55. The Pre-record time can
  • Hikvision DS-2CD2063G0-I | User Manual - Page 161
    Network Camera User Manual please refer to the Task 1: Set the Motion Detection Area in the Section 10.1.1.  Record Triggered by Alarm If you select Alarm, the video will
  • Hikvision DS-2CD2063G0-I | User Manual - Page 162
    Network Camera User Manual Configure Capture Schedule Purpose: You can configure the scheduled snapshot and event-triggered snapshot. The captured picture can be stored in the local storage or
  • Hikvision DS-2CD2063G0-I | User Manual - Page 163
    Network Camera User Manual 4. Click Save to save the settings. 5. Go to Capture Parameters tab to configure the capture parameters. (1) Check the Enable Timing Snapshot checkbox to enable continuous
  • Hikvision DS-2CD2063G0-I | User Manual - Page 164
    Network Camera User Manual Configuring Net HDD Before you start: The network disk should and password to guarantee the security if SMB/CIFS is selected. Note: Please refer to the NAS User Manual for creating the file path.  For your privacy and to better protect your system against security risks,
  • Hikvision DS-2CD2063G0-I | User Manual - Page 165
    Network Camera User Manual responsibility of the installer and/or end-user. (4) Click Save to add the network disk. 2. Initialize the added network disk. (1) Enter the HDD Settings interface,
  • Hikvision DS-2CD2063G0-I | User Manual - Page 166
    Network Camera User Manual Quota Settings Note: Up to 8 NAS disks can be connected to the camera. Memory Card Detection Purpose: is detected abnormal. Note: Memory card detection function is only supported by certain types of memory cards and camera models. If this tab page doesn't show on your web
  • Hikvision DS-2CD2063G0-I | User Manual - Page 167
    Network Camera User Manual Memory Card Detection 2. View the memory card status on Status Detection Save to save the settings.  Unlock (1) If you use the memory card on the camera that locks it, unlocking will be done automatically and no unlocking procedures are required on the part of users. 166
  • Hikvision DS-2CD2063G0-I | User Manual - Page 168
    (2) If you use the memory card (with a lock) on a different camera, you can go to HDD Management interface to unlock the memory card manually. Select the memory card, and click the Unlock button shown next to the Format button. Then input the correct password to unlock it. Notes: • The
  • Hikvision DS-2CD2063G0-I | User Manual - Page 169
    Network Camera User Manual 2. Check the Checkbox of Enable to enable the lite storage function. 3. Input the storage time in the text field. You can view the available space of the SD card on the page. 4. Click Save to save the settings. 168
  • Hikvision DS-2CD2063G0-I | User Manual - Page 170
    Network Camera User Manual Chapter 12 Playback Purpose: This section explains how to view the remotely recorded video files stored in the network disks or SD cards. Steps: 1. Click
  • Hikvision DS-2CD2063G0-I | User Manual - Page 171
    Network Camera User Manual The toolbar on the bottom of Playback interface can be used to control playing process. Button Playback Toolbar Table 12-1 Description of the buttons Operation
  • Hikvision DS-2CD2063G0-I | User Manual - Page 172
    Network Camera User Manual Chapter 13 Picture Click Picture to enter the picture searching interface. You can search, view, and download the pictures stored in the local storage or
  • Hikvision DS-2CD2063G0-I | User Manual - Page 173
    Network Camera User Manual Chapter 14 Application Click Application to enter the statistics counting interface. You can search, view, and download the counting data stored in the local storage or network storage. Note: Application function varies according to the different camera models. Face
  • Hikvision DS-2CD2063G0-I | User Manual - Page 174
    Network Camera User Manual counting data from application tab. To get more intuitional results, you can display the data in different charts. Steps: 1. Select the report type. Daily report,
  • Hikvision DS-2CD2063G0-I | User Manual - Page 175
    Network Camera User Manual Note: Daily report calculates the data on the date you selected; weekly report calculates for the week your selected date belongs to; monthly report calculates
  • Hikvision DS-2CD2063G0-I | User Manual - Page 176
    Network Camera User Manual different charts. Steps: 1. Select the report type. Daily report, weekly button to export the data in an excel file. Queue Management Statistics Purpose: Queue management supports data analysis and report output from multiple dimensions. Commonly Used Data Analysis • To see
  • Hikvision DS-2CD2063G0-I | User Manual - Page 177
    Network Camera User Manual • To compare the time and duration that a queue stays a certain length of different waiting time levels. Regional comparison and multiple waiting time level comparison are supported. Steps: 1. Select Statistic Type. Regional Comparison: Compares queuing-up people number of
  • Hikvision DS-2CD2063G0-I | User Manual - Page 178
    Network Camera User Manual 2. Select Report Type. Daily report, weekly report, and monthly report are supported. 3. Select Statistics Time. 4. length. Regional comparison and multiple queue length level comparison are supported. Steps: 1. Select Statistic Type. Regional Comparison: Compares the
  • Hikvision DS-2CD2063G0-I | User Manual - Page 179
    Network Camera User Manual 3. Select Statistics Time. 4. Click Counting to generate the report. 5. (Optional) Click Export in the upper right corner to export the data in desired format (.txt
  • Hikvision DS-2CD2063G0-I | User Manual - Page 180
    Network Camera User Manual Appendix Appendix 1 SADP Software Introduction  Description of SADP SADP (Search Active Devices Protocol) is a kind of user-friendly and installation-free online device search tool.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 181
    Network Camera User Manual  Search online devices manually You can also click to refresh the online device list manually. The newly searched devices will be added to the list. You can click or on each column heading to order the information; you can click
  • Hikvision DS-2CD2063G0-I | User Manual - Page 182
    Network Camera User Manual Figure A.1.2 Modify Network Parameters 181
  • Hikvision DS-2CD2063G0-I | User Manual - Page 183
    Network Camera User Manual Appendix 2 Port Mapping The following settings are for TP-LINK router (TL- the LAN parameters 3. Set the port mapping in the virtual severs of Forwarding. By default, camera uses port 80, 8000 and 554. You can change these ports value with web browser or client software.
  • Hikvision DS-2CD2063G0-I | User Manual - Page 184
    Camera User Manual another camera as 81, 8001, 555, 8201 with IP 192.168.1.24. Refer to the steps as below: Steps: 1. As the settings mentioned above, map the port 80, 8000, 554 and 8200 for the network camera at 192.168.1.23 2. Map the port 81, 8001, 555 and 8201 for the network camera
  • Hikvision DS-2CD2063G0-I | User Manual - Page 185
    Network Camera User Manual 184
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
Network Camera User Manual
0
User Manual
UD09650B
Network Camera