Hikvision DS-2CD2063G0-I Quick Start Guide

Hikvision DS-2CD2063G0-I Manual

Get Hikvision DS-2CD2063G0-I PDF manuals and user guides View all Hikvision DS-2CD2063G0-I manuals
Add to My Manuals
Save this manual to your list of manuals

Hikvision DS-2CD2063G0-I manual content summary:

  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 1
    Network Bullet Camera Quick Start Guide 0
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 2
    prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual This Manual is applicable to Network Bullet Camera. The Manual includes instructions for using and
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 3
    Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED "AS IS", WITH ALL FAULTS AND ERRORS, AND HIKVISION RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 4
    Network Bullet Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 5
    Network Bullet Camera·Quick Start Guide FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 6
    Network Bullet Camera·Quick Start Guide supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B)
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 7
    Network Bullet Camera·Quick Start Guide fonctionner avec une antenne d'un type et d'un gain maximal é à une distance minimale de 20 cm entre le radiateur et votre corps. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 8
    Network Bullet Camera·Quick Start Guide Warnings ● Proper configuration of all passwords and the power cable, and then please contact the service center. Cautions ● Make sure the power supply voltage is correct before using the camera. ● Do not drop the camera or subject it to physical shock. 7
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 9
    Bullet Camera·Quick Start Guide ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt. ● Do not aim the camera
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 10
    according to the instructions provided by the battery manufacturer. ● If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 11
    32 5 Operating via Hik-Connect App 35 5.1 Enable Hik-Connect Service on Camera 35 5.1.1 Enable Hik-Connect Service via SADP Software .. 35 Enable Hik-Connect Service via Web Browser .... 36 5.2 Hik-Connect Setup 38 5.3 Adding Camera to Hik-Connect 38 5.4 Initializing the Memory Card 40 10
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 12
    Network Bullet Camera·Quick Start Guide 1 Appearance Description 1.1 Type I 1 23 4 5 8 9 6 10 7 Overview of Type I Description No. Description 1 3-Axis Adjustment Bracket 2 Back Cover 3 Front Cover 4 Mic 5 Lens Status Indicator 6 ● Flashing Blue: Normal Wi-Fi connection. 11
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 13
    Bullet Camera·Quick Start Guide No. Description ● Solid Red: The camera is during startup. ● Flashing red and blue: The camera has started and starts Wi-Fi configuration. ● Flashing Red: ● Fast Flashing: The network connection failed. ● Slow Flashing: Memory card error or other problems
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 14
    Network Bullet Camera·Quick Start Guide 1 2 34 5 9* 10 8 6 7 Overview of Type III Description No. Description 1 3-Axis Adjustment Bracket 2 Back Cover 3 Front Cover 4 Sun Shield 5 IR LED Cover 6 Lens 7 IR LED 8 Network
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 15
    The network connection failed. ● Slow Flashing: Memory card error or other problems. 13 Mic Note: ● For type II and III camera, only certain models support the memory card installation. ● Hold RESET about 10s when the camera is powering on or rebooting to restore the default settings, including
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 16
    Network Bullet Camera·Quick Start Guide Note:  The WPS button works as a reset button only when you press it when the camera is powering on.  Press the WPS button on the camera, and then press the WPS button on the router will work as well, and the expire time of WPS connection on the camera is
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 17
    products for the installation environment. ● Make sure that the wall is strong enough to withstand four times the weight of the camera and the bracket. For the camera that supports IR, you are required to pay attention to the following precaution to prevent IR reflection: Make sure that there is no
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 18
    Start Guide Antenna Wi-Fi Interface Antenna Wi-Fi Antenna Antenna Interface Mount the Antenna 2. Tighten the locking nut using the supplied wrench. Locking Nut Locking Nut Tighten the Locking Nut 2.1.2 Memory Card Installation Only certain models of the type II and type III support memory
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 19
    Network Bullet Camera·Quick Start Guide 2. Insert the memory card into the slot. 3. Replace the slot cover and fix the screws. Install the Memory Card 2.1.3 Wall/Ceiling Mounting Type I, II and III camera support wall and ceiling mounting and the steps are similar. Here takes type I as an example to
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 20
    Network Bullet Camera·Quick Start Guide Hole Φ55 Hole Hole 3-Φ4.5 Drill the Holes 2. If you need to route cables through the wall or ceiling, cut a cable hole according to the drill
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 21
    Network Bullet Camera·Quick Start Guide 3-axis (pan/tilt/rotation) adjusting allows adjustment for optimum camera rotation and placement. 1). Loosen the 3-axis adjusting nut. 2). Adjust the panning, tilting and rotation position of the camera. The adjusting range of the panning is from 0° to 360°,
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 22
    ·Quick Start Guide If the camera is installed outdoor, you can use the waterproof accessory for the network cable after the camera is secured on the installation surface. ①② ③ ④ ⑤ ⑥⑦ Figure 2-7 Waterproof Accessory Components Table 2-1 Components No. Components 1 Camera's Network Interface
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 23
    Network Bullet Camera·Quick Start Guide must face the waterproof endcap), and the waterproof endcap ④ in order. Crimp an RJ-45 network plug ③onto the end of the cable, taking care to insert the twisted pairs of wires in correct order. Place the O-type gasket ② onto the end of the camera's network
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 24
    Network Bullet Camera·Quick Start Guide Align the snap and notch. i. Insert ⑤ into ④. ii. Secure ⑥ with ④. Camera Switch/Router Figure 2-8 Waterproof Accessory Installation 23
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 25
    camera is powered on. You can activate, add and configure the camera on the NVR. Make sure the NVR's Wi-Fi has been configured in advance. Refer to Quick Start Guide contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 26
    via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for Activation via Client Software. 3.2.1 Activation via Web
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 27
    Network Bullet Camera·Quick Start Guide  The default IP address of the camera is 192.168.1.64.  The computer and the camera should belong to the same subnet.  For the camera enables the DHCP by default, you need to use the SADP software to search the IP address. Figure 3-3 Activation Interface(
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 28
    Network Bullet Camera·Quick Start Guide 3.2.2 Activation via SADP Software SADP software is used for detecting the online device, activating the camera, and resetting Interface Note: The SADP software supports activating the camera in batch. Refer to the user manual of SADP software for details. 27
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 29
    Network Bullet Camera·Quick Start Guide 3. Create and input the new password in the password field, and monthly or weekly can better protect your product. Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Click Activate
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 30
    Bullet Camera·Quick Start Guide For IP address modification via client software, refer to the user manual of client software. Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 31
    Network Bullet Camera·Quick Start Guide Figure 3-5 Modify the IP Address Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. 30
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 32
    Network Bullet Camera·Quick Start Guide The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details. 31
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 33
    Network Bullet Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement:  Operating System: Microsoft the web browser. 2. In the browser address bar, input the IP address of the network camera, and press the Enter key to enter the login interface. Note: The default IP address is
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 34
    Network Bullet Camera·Quick Start Guide The device IP address gets locked if the admin user performs 7 failed password attempts (5 attempts for the user/operator). 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 35
    Network Bullet Camera·Quick Start Guide For detailed instructions of further configuration, please refer to the User Manual of Network Camera. 34
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 36
    Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 37
    Network Bullet Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. Enable Hik-Connect Service via Web Browser
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 38
    Network Bullet Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera. Note: The verification code is required when you add the camera
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 39
    Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps: 1. Use a network cable to connect the camera with a router if the camera does not support Wi-Fi. Figure 5-3 Connect a Router Note: After the
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 40
    Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera you enabling Hik-Connect service on camera. ● If you
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 41
    Network Bullet Camera·Quick Start Guide 5.4 Initializing the Memory Card Note: The memory card is only supported by certain models. See the actual device for details. Steps: Check the memory to Normal. You can then start recording any event triggered video in the camera such as motion detection. 40
  • Hikvision DS-2CD2063G0-I | Quick Start Guide - Page 42
    B 0 UD09877
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
0
Network Bullet Camera
Quick Start Guide