Hitachi 42HDS69 Owners Guide - Page 35

The Remote Control for Additional Audio Equipment

Get Hitachi 42HDS69 - 42inch Plasma TV PDF manuals and user guides View all Hitachi 42HDS69 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

The Remote Control The Remote Control for Additional Audio Equipment Operating the precoded function for your Audio component. ቢ This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component (refer to pages 37-38 for pre-codes). 1. Turn ON your Audio component you wish to control ቢ with the Remote. 2. Aim the remote control at the front of your Audio ባ component. ቢ 3. To switch to Audio (AMP) component pre-coded mode, use the SOURCE ACCESS buttons (̇ or ̈) on the remote control to position the LED light to ባ the corresponding selection. 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your Audio ባ component, as shown on pages 37-38. Release the ENT button. The indicator light will flash 3 times if the code was accepted. 5. Aim the remote at the Audio component and press ቢ the POWER button. The remote will turn off your Audio component when the correct four digit preset code is entered. When this occurs, the ቢ remote control is programmed for your Audio component. If the Audio component does not turn off, try a different four digit preset code. 6. The remote will now control your Audio component. 7. Repeat steps 1 - 6 if you wish to program the remote to control another Audio component. NOTE: 1. If your Audio component cannot be operated after performing the above procedures, your Audio component code has not been precoded into the remote. 2. In the unlikely event that your Audio component cannot be operated after performing the above procedures, please consult your Audio component operating guide. 3. The remote control will remember the codes you have programmed until the batteries are removed from the from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. MY AUDIO COMPONENT CODE IS: NOTE: Refer to instruction manual of the VCR/PVR for operation of the buttons exclusively for the VCR/PVR. ቢ PRECODED AUDIO Buttons These buttons transmit the chosen precoded Audio component codes. ባ EXCLUSIVE TV Buttons These buttons are for operating the TV. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Operating the precoded function for your Audio
component.
This remote is designed to operate different types of
Audio component.
You must first program the remote
to match the remote system of your Audio component
(refer to pages 37-38 for pre-codes).
1.
Turn ON your Audio component you wish to control
with the Remote.
2.
Aim the remote control at the front of your Audio
component.
3.
To switch to Audio (AMP) component pre-coded
mode, use the SOURCE ACCESS buttons (
³
or
´
)
on the remote control to position the LED light to
the corresponding selection.
4.
Hold down the ENT button on the remote and enter
the four digit preset code that matches your Audio
component, as shown on pages 37-38.
Release
the ENT button.
The indicator light will flash 3
times if the code was accepted.
5.
Aim the remote at the Audio component and press
the POWER button.
The remote will turn off your
Audio component when the correct four digit
preset code is entered.
When this occurs, the
remote control is programmed for your Audio
component.
If the Audio component does not turn
off, try a different four digit preset code.
6.
The remote will now control your Audio
component.
7.
Repeat steps 1 - 6 if you wish to program the
remote to control another Audio component.
NOTE:
1. If your Audio component cannot be
operated after performing the above
procedures, your Audio component code
has not been precoded into the remote.
2. In the unlikely event that your Audio
component cannot be operated after
performing the above procedures, please
consult your Audio component operating
guide.
3.
The remote control will remember the
codes you have programmed until the
batteries are removed from the from the
remote control.
After replacing the
batteries repeat the entire programming
procedure as stated above.
¹
PRECODED AUDIO Buttons
These buttons transmit the chosen precoded Audio
component codes.
À
EXCLUSIVE TV Buttons
These buttons are for operating the TV.
MY AUDIO COMPONENT
CODE IS:
NOTE:
Refer to instruction manual of the VCR/PVR
for operation of the buttons exclusively for
the VCR/PVR.
35
The Remote Control for Additional Audio Equipment
The Remote Control
¹
À
À
À
¹
¹
¹
¹