Hitachi 42V715 Owners Guide - Page 33

Using The Remote To Control Cable Box, Functions

Get Hitachi 42V715 - 42inch Rear Projection TV PDF manuals and user guides View all Hitachi 42V715 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS Operating the precoded function for your cable box. This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of your cable box (refer to pages 39-40 for pre-codes). 1. Turn ON your cable box. 2. Aim the remote control at the front of your cable box. 3. To switch to Cable (CBL) pre-coded mode, use the SOURCE ACCESS buttons (̇ , ̈) on the remote control to position the LED light to the corresponding selection. 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your cable box as shown on pages 3940. Release the ENT button. The indicator light will flash 3 times if the code was accepted. 5. Aim the remote at the cable box and press the POWER button. The remote will turn off your cable box when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different four digit preset code. ቢ 6. The remote will now control your Cable box. NOTES: 1. If your cable box cannot be operated after performing the above procedures, your cable box code has not been precoded into the remote. 2. In the unlikely event that your cable box cannot be operated after performing the above procedures, please consult your cable box operating guide. 3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. ቢ PRECODED CABLE BOX buttons These buttons transmit the chosen precoded cable codes. ባ EXCLUSIVE TV buttons These buttons are for operating the TV. ባ GUIDE ቢ ባ C.C. ባ ቢ ቢ THE REMOTE CONTROL MY CABLE BOX CODE IS: NOTE: Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
33
USING THE REMOTE TO CONTROL CABLE BOX
FUNCTIONS
Operating the precoded function for your cable box.
This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of
your cable box (refer to pages 39-40 for pre-codes).
1.
Turn ON your cable box.
2.
Aim the remote control at the front of your cable box.
3.
To switch to Cable (CBL) pre-coded mode, use the SOURCE ACCESS buttons (
³
,
´
) on the remote control to position the LED
light to the corresponding selection.
4.
Hold down the ENT button on the remote and enter the four digit preset code that matches your cable box as shown on pages 39-
40.
Release the ENT button.
The indicator light will flash 3 times if the code was accepted.
5.
Aim the remote at the cable box and press the POWER button.
The remote will turn off your cable box when the correct four digit
preset code is entered.
When this occurs, the remote control is programmed for your cable box.
If the cable box does not turn off,
try a different four digit preset code.
6.
The remote will now control your Cable box.
NOTES:
1.
If your cable box cannot be operated after performing the
above procedures, your cable box code has not been
precoded into the remote.
2.
In the unlikely event that your cable box cannot be
operated after performing the above procedures, please
consult your cable box operating guide.
3.
The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control.
After replacing the batteries repeat the
entire programming procedure as stated above.
±
PRECODED CABLE BOX buttons
These buttons transmit the chosen precoded cable codes.
²
EXCLUSIVE TV buttons
These buttons are for operating the TV.
GUIDE
±
²
±
²
²
±
C.C.
±
MY CABLE BOX CODE IS:
NOTE:
Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box.
THE REMOTE CONTROL