Hitachi 42V715 Owners Guide - Page 34

Using The Remote To Control, Set-top-box/satellite Receiver Functions

Get Hitachi 42V715 - 42inch Rear Projection TV PDF manuals and user guides View all Hitachi 42V715 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

USING THE REMOTE TO CONTROL SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS Operating the precoded function for your set-top-box/satellite receiver. This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set-top-box/satellite systems (refer to pages 39-40 for pre-codes). 1. Turn ON your set-top-box/satellite systems. 2. Aim the remote control at the front of your set-top-box/satellite systems. 3. To switch to set-top-box/satellite (STB) pre-coded mode, use the SOURCE ACCESS buttons (̇ , ̈) on the remote control to position the LED light to the corresponding selection. 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your set-top-box/satellite receiver as shown on page 39-40. Release the ENT button. The indicator light will flash 3 times if the code was accepted. 5. Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satellite receiver when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your settop-box/satellite receiver. If the set-top-box/satellite receiver does not turn off, try a different four digit preset code. 6. The remote will now control your set-top-box/satellite receiver. ቢ NOTES: 1. If your set-top-box/satellite receiver cannot be operated after performing the above procedures, your set-topbox/satellite receiver code has not been precoded into the remote. 2. In the unlikely event that your set-top-box/satellite receiver cannot be operated after performing the above procedures, please consult your set-top-box/satellite receiver operating guide. 3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. ቢ PRE-CODED SET-TOP-BOX/SATELLITE RECEIVER buttons These buttons transmit the chosen pre-coded set-topbox/satellite codes. ባ EXCLUSIVE TV buttons These buttons are for operating the TV. ባ GUIDE ቢ ባ C.C. ባ ቢ ቢ THE REMOTE CONTROL MY SATELLITE RECEIVER/STB CODE IS: NOTE: Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-topbox/satellite receiver. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
34
USING THE REMOTE TO CONTROL
SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS
Operating the precoded function for your set-top-box/satellite receiver.
This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the
remote system of your set-top-box/satellite systems (refer to pages 39-40 for pre-codes).
1.
Turn ON your set-top-box/satellite systems.
2.
Aim the remote control at the front of your set-top-box/satellite systems.
3.
To switch to set-top-box/satellite (STB) pre-coded mode, use the SOURCE ACCESS buttons (
³
,
´
) on the remote control to posi-
tion the LED light to the corresponding selection.
4.
Hold down the ENT button on the remote and enter the four digit preset code that matches your set-top-box/satellite receiver as
shown on page 39-40.
Release the ENT button.
The indicator light will flash 3 times if the code was accepted.
5.
Aim the remote at the set-top-box/satellite receiver and press the POWER button.
The remote will turn off your set-top-box/satel-
lite receiver when the correct four digit preset code is entered.
When this occurs, the remote control is programmed for your set-
top-box/satellite receiver.
If the set-top-box/satellite receiver does not turn off, try a different four digit preset code.
6.
The remote will now control your set-top-box/satellite receiver.
NOTES:
1.
If your set-top-box/satellite receiver cannot be operated
after performing the above procedures, your set-top-
box/satellite receiver code has not been precoded into the
remote.
2.
In the unlikely event that your set-top-box/satellite
receiver cannot be operated after performing the above
procedures, please consult your set-top-box/satellite
receiver operating guide.
3.
The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control.
After replacing the batteries repeat the
entire programming procedure as stated above.
±
PRE-CODED SET-TOP-BOX/SATELLITE RECEIVER
buttons
These buttons transmit the chosen pre-coded set-top-
box/satellite codes.
²
EXCLUSIVE TV buttons
These buttons are for operating the TV.
GUIDE
±
²
±
²
²
±
C.C.
±
MY SATELLITE RECEIVER/STB CODE IS:
NOTE:
Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-top-
box/satellite receiver.
THE REMOTE CONTROL