Hitachi 42V715 Owners Guide - Page 37

Using Your Remote, To Control Additional Audio Equipment

Get Hitachi 42V715 - 42inch Rear Projection TV PDF manuals and user guides View all Hitachi 42V715 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

THE REMOTE CONTROL USING YOUR REMOTE TO CONTROL ADDITIONAL AUDIO EQUIPMENT Operating the precoded function for your Audio component. This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component (refer to pages 39-40 for pre-codes). 1. Turn ON your Audio component you wish to control with the Remote. 2. Aim the remote control at the front of your Audio component. 3. To switch to Audio (AMP) component pre-coded mode, use the SOURCE ACCESS buttons (̇ , ̈) on the remote control to position the LED light to the corresponding selection. 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your Audio component, as shown on pages 39-40. Release the ENT button. The indicator light will flash 3 times if the code was accepted. 5. Aim the remote at the Audio component and press the POWER button. The remote will turn off your Audio component when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio component does not turn off, try a different four digit preset code. 6. The remote will now control your Audio component. 7. Repeat steps 1 - 6 if you wish to program the remote to control another Audio component. NOTES: 1. If your Audio component cannot be operated after performing the above procedures, your Audio component's code has not been precoded into the remote. 2. In the unlikely event that your Audio component cannot be operated after performing the above procedures, please consult your Audio equipment operating guide. 3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. 4. CD precode library is included in the AMP mode. Default device for this mode is Hitachi Audio/Video Receiver (AVR/AMP). 5. INPUT, GUIDE, Channel (up/down), Volume (up/down) and REC button are not for CD devices. ቢ PRECODED AUDIO Buttons These buttons transmit the chosen precoded Audio component codes. ባ EXCLUSIVE TV Buttons These buttons are for operating the TV. ቢ ቢ ባ GUIDE ቢ ባ C.C. ቢ ቢ MY AUDIO EQUIPMENT CODE IS: CD AMP/RCVR NOTES: 1. The REC (Record) button only applies to some precoded amplifier/receiver codes. 2. Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
37
USING YOUR REMOTE
TO CONTROL ADDITIONAL AUDIO EQUIPMENT
GUIDE
±
²
±
²
C.C.
±
±
±
MY AUDIO EQUIPMENT CODE IS:
NOTES:
1.
The REC (Record) button only applies to some precoded amplifier/receiver codes.
2.
Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment.
CD
AMP/RCVR
Operating the precoded function for your Audio component.
This remote is designed to operate different types of Audio component.
You must first program the remote to match the remote system
of your Audio component (refer to pages 39-40 for pre-codes).
1.
Turn ON your Audio component you wish to control with the Remote.
2.
Aim the remote control at the front of your Audio component.
3.
To switch to Audio (AMP) component pre-coded mode, use the SOURCE ACCESS buttons (
³
,
´
) on the remote control to posi-
tion the LED light to the corresponding selection.
4.
Hold down the ENT button on the remote and enter the four digit preset code that matches your Audio component, as shown on
pages 39-40.
Release the ENT button.
The indicator light will flash 3 times if the code was accepted.
5.
Aim the remote at the Audio component and press the POWER button.
The remote will turn off your Audio component when the
correct four digit preset code is entered.
When this occurs, the remote control is programmed for your Audio component.
If the
Audio component does not turn off, try a different four digit preset code.
6.
The remote will now control your Audio component.
7.
Repeat steps 1 - 6 if you wish to program the remote to control another Audio component.
NOTES:
1.
If your Audio component cannot be operated after
performing
the
above
procedures,
your
Audio
component’s code has not been precoded into the
remote.
2.
In the unlikely event that your Audio component cannot be
operated after performing the above procedures, please
consult your Audio equipment operating guide.
3.
The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control.
After replacing the batteries repeat the
entire programming procedure as stated above.
4.
CD precode library is included in the AMP mode.
Default
device for this mode is Hitachi Audio/Video Receiver
(AVR/AMP).
5.
INPUT, GUIDE, Channel (up/down), Volume (up/down)
and REC button are not for CD devices.
±
PRECODED AUDIO Buttons
These buttons transmit the chosen precoded Audio
component codes.
²
EXCLUSIVE TV Buttons
These buttons are for operating the TV.
THE REMOTE CONTROL