Hitachi 43FDX01B Owners Guide - Page 29

USING THE REMOTE TO CONTROL SATELLITE RECEIVER, FUNCTIONS, Operating the precoded function for your

Get Hitachi 43FDX01B PDF manuals and user guides View all Hitachi 43FDX01B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

USING THE REMOTE TO CONTROL SATELLITE RECEIVER FUNCTIONS Operating the precoded function for your satellite receiver. This remote is designed to operate different types of satellite systems. You must first program the remote to match the remote system of your satellite receiver. (refer to page 33.) 1. Turn ON your satellite receiver. 2. Aim the remote control at the front of your satellite receiver. 3. Press the SATELLITE (SAT) button on the remote to switch to satellite pre-coded mode. 4. Hold down the SAT button on the remote and enter the two digit preset code that matches your satellite receiver as shown on page 33. The indicator light will flash 3 times if the code was accepted. 5. Aim the remote at the satellite receiver and press the POWER button. The remote will turn off your satellite receiver when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your satellite receiver. If the satellite receiver does not turn off, try a different two digit preset code. 6. The remote will now control your satellite receiver. NOTES: 1. If your satellite receiver cannot be operated after performing the above procedures, your satellite receiver code has not been precoded into the remote. 2. In the unlikely event that your satellite receiver cannot be operated after performing the above procedures, please consult your satellite receiver operating guide. 3. The remote control will remember the codes you have programmed in until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure stated above. 4. The INPUT button will act at the TV/SAT button when in SAT mode. (1) SATELLITE (SAT) button This button allows the remote to control your satellite receiver by setting it to SATELLITE mode. (2) PRECODED SATELLITE RECEIVER buttons These buttons transmit the chosen precoded cable codes. (3) EXCLUSIVE TV buttons These buttons are for operating the TV. MY SATELLITE RECEIVER CODE IS NOTE: Refer to instruction manual of the Satellite Receiver for operation of the buttons exclusively for the Satellite Receiver. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
29
USING THE REMOTE TO CONTROL SATELLITE RECEIVER
FUNCTIONS
Operating the precoded function for your satellite receiver.
This remote is designed to operate different types of satellite systems. You must first program the remote to match the
remote system of your satellite receiver.
(refer to page 33.)
1. Turn ON your satellite receiver.
2. Aim the remote control at the front of your satellite receiver.
3. Press the SATELLITE (SAT) button on the remote to switch to satellite pre-coded mode.
4. Hold down the SAT button on the remote and enter the two digit preset code that matches your satellite receiver as
shown on page 33.
The indicator light will flash 3 times if the code was accepted.
5. Aim the remote at the satellite receiver and press the POWER button.
The remote will turn off your satellite receiver
when the correct two digit preset code is entered.
When this occurs, the remote control is programmed for your
satellite receiver.
If the satellite receiver does not turn off, try a different two digit preset code.
6. The remote will now control your satellite receiver.
NOTES:
1
. If your satellite receiver cannot be operated after performing the above procedures, your satellite receiver code has
not been precoded into the remote.
2. In the unlikely event that your satellite receiver cannot be operated after performing the above procedures, please
consult your satellite receiver operating guide.
3. The remote control will remember the codes you have programmed in until the batteries are removed from the
remote control. After replacing the batteries repeat the entire programming procedure stated above.
4.
The INPUT button will act at the TV/SAT button when in SAT mode.
(1) SATELLITE (SAT) button
This button allows the remote to control your satellite receiver by setting it to SATELLITE mode.
(2) PRECODED SATELLITE RECEIVER buttons
These buttons transmit the chosen precoded cable codes.
(3) EXCLUSIVE TV buttons
These buttons are for operating the TV.
MY SATELLITE RECEIVER CODE IS:___________________
NOTE:
Refer to instruction manual of the Satellite Receiver
for operation of the buttons exclusively for
the Satellite
Receiver.