Hitachi 50HDT50 Owners Guide - Page 26

How To Use The Remote, To Control Your Plasma Tv - reset

Get Hitachi 50HDT50 PDF manuals and user guides View all Hitachi 50HDT50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

THE REMOTE CONTROL MENU LAST CH GUIDE/TV SCHD VID 4 VID 5 STB POWER CBL VCRSOURCE WIZARTDAPE AMP 3 TV CD DVD 1 2 5 6 9 4 7 8 INFO MODE 0 ASPECT A/V NET SLEEP TV/RGB EXIT ANT CH SELECT VOL MUTE SVCS VCR PLUS+ VID 1 VID 2 PIP FREEZE VID 3 PIP CH PIP ACCESS VIDEO SWAP PIP MODE REC CLU-5723TSI HOW TO USE THE REMOTE TO CONTROL YOUR PLASMA TV ቨ CD, PVR, AMP buttons When pressed, each of these buttons will blink to indicate the remote is in Audio mode (see page 39). ቩ CHANNEL selector buttons CHANNEL selector buttons are used to select channels, lock access code, etc. Enter one, two, or three numbers to select channels. Enter "0" first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the "1" button, wait until two dashes appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons. Channel selection may also be performed by pressing CH up (̆) or down (̄). NOTE: The Plasma TV may not receive some channels if you are not in the correct ANTENNA/CABLE mode (see page 49). ቪ SLEEP button Press this button to display the sleep timer in the lower center of the screen. Every subsequent press of this button will add 15 minutes to this timer, up to a maximum of three hours. Once set, use INFO when you want to view time remaining. If the SLEEP button is pressed while the timer is set, it will reset to the original condition. ቫ INFO button Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second audio program (SAP), the time, CHANNEL ID and if the SLEEP timer is set. 3:32 PM Ant A 22 Stereo R 1080i Format Time Main Picture Source Audio Broadcast Broadcast Rating Signal Format 3:32 PM S-IN:3 VID 3 When an S-VIDEO Input is connected to VIDEO: 3. Day/Night Closed Mode Captioning Day CC Off 4:3 Expanded View 0:00 AM Off Timer Zzzz -:-- Wide Mode Sleep Timer 3:32 PM YPBPR:1 VID 1 When a COMPONENT VIDEO: Y-PBPR Input is connected to VIDEO: 1. ቭ ANTENNA button The ANT button will select between Antenna A and Antenna B each time the button is pressed. 3:32 PM Ant A 15 Stereo G ANT 3:32 PM Ant B 22 Stereo R ቮ TV/RGB button Press this button to toggle between RGB (Analog) mode and TV mode. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
26
HOW TO USE THE REMOTE
TO CONTROL YOUR PLASMA TV
·
CD, PVR, AMP buttons
When pressed, each of these buttons will blink to indicate the remote is in Audio mode (see page 39).
¹
CHANNEL selector buttons
CHANNEL selector buttons are used to select channels, lock access code, etc.
Enter one, two, or three numbers to select channels.
Enter “0” first for channels 1 to 9, or simply press the single digit channel you
wish to tune then wait a few seconds for the TV to tune.
For channels 100 and above, press the “1” button, wait until two dashes
appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons.
Channel selection may also be performed by pressing CH up (
±
) or down (
²
).
º
SLEEP button
Press this button to display the sleep timer in the lower center of the screen.
Every subsequent press of this button will add 15 min-
utes to this timer, up to a maximum of three hours.
Once set, use INFO when you want to view time remaining.
If the SLEEP but-
ton is pressed while the timer is set, it will reset to the original condition.
»
INFO button
Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second
audio program (SAP), the time, CHANNEL ID and if the SLEEP timer is set.
¼
ANTENNA button
The ANT button will select between Antenna A and Antenna B each time the button is pressed.
NOTE:
The Plasma TV may not receive some channels if you are not in the correct ANTENNA/CABLE mode (see page 49).
ANT
Ä
TV/RGB button
Press this button to toggle between RGB (Analog) mode and TV mode.
When an S-VIDEO
Input is connected to
VIDEO: 3.
When a COMPONENT
VIDEO: Y-P
B
P
R
Input
is connected to
VIDEO: 1.
3:32 PM
S-IN:3
VID 3
Main Picture Source
Time
Wide
Mode
Day/Night
Mode
Closed
Captioning
Off Timer
Sleep Timer
3:32 PM
Ant
A
22
Stereo
R
1080i Format
Day
4:3 Expanded
Off
0:00 AM
-:--
View
Zzzz
CC
Audio Broadcast
Broadcast Rating
Signal Format
THE REMOTE CONTROL
3:32 PM
YPBPR:1
VID 1
3:32 PM
Ant
B
22
Stereo
R
3:32 PM
Ant
A 15
Stereo
G