Hitachi 51S500 Owners Guide - Page 31

Using The Remote To Control Cable Box Functions

Get Hitachi 51S500 PDF manuals and user guides View all Hitachi 51S500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

THE REMOTE CONTROL USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS Operating the precoded function for your cable box. This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of your cable box (refer to page 36). 1. Turn ON your cable box. 2. Aim the remote control at the front of your cable box. 3. Press and release the Cable (CBL) button to switch to Cable pre-coded mode. 4. Hold down the CBL button on the remote and enter the two digit preset code that matches your cable box as shown on page 36. The indicator light will flash 3 times if the code was accepted. 5. Aim the remote at the cable box and press the POWER button. The remote will turn off your cable box when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different two digit preset code. 6. The remote will now control your Cable box. NOTES: 1. If your cable box cannot be operated after performing the above procedures, your cable box code has not been precoded into the remote. 2. In the unlikely event that your cable box cannot be operated after performing the above procedures, please consult your cable box operating guide. 3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. 4. The LAST CH button will act as the cable box ENTER button if required. 5. The SLEEP button will act as your cable box '100' button if required. 6. The ANT button will act as the TV/STB button when in STB mode. ባ POWER TV DVD VCR CBL SOURCE WIZARD CD PVR STB AMP 1 2 3 ቢ 4 5 6 ባ 7 8 9 SLEEP C.C. ANT 0 INFO PHOTO ASPECT VIRTUAL HD ቤ ቤ ቤ ቤ MENU EXIT VOL SELECT CH MUTE LAST CH VID 1 VID 2 PIP VID 3 SURF VID 5 VID 4 FREEZE PIP MODE PIP ACCESS SWAP DAY/NIGHT ባ ቤ ቢ CABLE (CBL) button This button allows the remote to control your cable box by setting it to CABLE mode. ባ PRECODED CABLE BOX buttons These buttons transmit the chosen precoded cable codes. ቤ EXCLUSIVE TV buttons These buttons are for operating the TV. REC MY CABLE BOX CODE IS: NOTE: Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
31
THE REMOTE CONTROL
USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS
Operating the precoded function for your cable box.
This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of
your cable box (refer to page 36).
1.
Turn ON your cable box.
2.
Aim the remote control at the front of your cable box.
3.
Press and release the Cable (CBL) button to switch to Cable pre-coded mode.
4.
Hold down the CBL button on the remote and enter the two digit preset code that matches your cable box as shown on page 36.
The indicator light will flash 3 times if the code was accepted.
5.
Aim the remote at the cable box and press the POWER button.
The remote will turn off your cable box when the correct two digit
preset code is entered.
When this occurs, the remote control is programmed for your cable box.
If the cable box does not turn off,
try a different two digit preset code.
6.
The remote will now control your Cable box.
NOTES:
1.
If your cable box cannot be operated after performing the
above procedures, your cable box code has not been
precoded into the remote.
2.
In the unlikely event that your cable box cannot be
operated after performing the above procedures, please
consult your cable box operating guide.
3.
The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control.
After replacing the batteries repeat the
entire programming procedure as stated above.
4.
The LAST CH button will act as the cable box ENTER
button if required.
5.
The SLEEP button will act as your cable box ‘100’ button
if required.
6.
The ANT button will act as the TV/STB button when in
STB mode.
´
CABLE (CBL) button
This button allows the remote to control your cable box by
setting it to CABLE mode.
µ
PRECODED CABLE BOX buttons
These buttons transmit the chosen precoded cable codes.
²
EXCLUSIVE TV buttons
These buttons are for operating the TV.
´
µ
µ
²
²
µ
²
²
²
POWER
TV
VCR
CBL
DVD
1
2
4
5
6
3
7
8
9
0
INFO
SLEEP
PHOTO
EXIT
MENU
CH
VOL
MUTE
PIP
SURF
SWAP
FREEZE
PIP MODE
PIP ACCESS
DAY/NIGHT
SOURCE WIZARD
REC
SELECT
C.C.
ASPECT
STB
ANT
LAST CH
VID 1
VID 2
VID 3
VID 4
VID 5
PVR
CD
AMP
VIRTUAL HD
MY CABLE BOX CODE IS:
NOTE:
Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box.