Hitachi 55HDS52 Owners Guide - Page 32

The Remote Control for Set-Top-Box/Satellite Receiver, Functions

Get Hitachi 55HDS52 - 55inch Plasma TV PDF manuals and user guides View all Hitachi 55HDS52 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

The Remote Control The Remote Control for Set-Top-Box/Satellite Receiver Functions Operating the precoded function for your set-top- box/satellite receiver. ቢ This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your settop-box/satellite systems (refer to pages 37-38 for precodes). 1. Turn ON your set-top-box/satellite systems. 2. Aim the remote control at the front of your set-top- ባ box/satellite systems. 3. To switch to set-top-box/satellite (STB) pre-coded mode, use the SOURCE ACCESS buttons (̇ or ̈) on the remote control to position the LED light to ቢ the corresponding selection. 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your settop-box/satellite receiver as shown on page 37-38. ቢ Release the ENT button. The indicator light will ባ flash 3 times if the code was accepted. 5. Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satellite receiver when the ባ ቢ correct four digit preset code is entered. When this ቢ occurs, the remote control is programmed for your set-top-box/satellite receiver. If the set-top- box/satellite receiver does not turn off, try a different four digit preset code. 6. The remote will now control your set-topbox/satellite receiver. NOTE: 1. If your set-top-box/satellite receiver cannot be operated after performing the above procedures, your set-top-box/ satellite receiver code has not been precoded into the remote. 2. In the unlikely event that your set-topbox/satellite receiver cannot be operated after performing the above procedures, please consult your set-top-box/satellite receiver operating guide. 3. The remote control will remember the codes you have programmed until the batteries are removed from the from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. MY Satellite RECEIVER/ SET-TOP-BOX CODE IS: NOTE: Refer to instruction manual of the Set-TopBox/Satellite Receiver for operation of the buttons exclusively for the Set-TopBox/Satellite Receiver. ቢ PRE-CODED SET-TOP-BOX/SATELLITE RECEIVER buttons These buttons transmit the chosen pre-coded settop-box/satellite codes. ባ EXCLUSIVE TV buttons These buttons are for operating the TV. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
32
Operating the precoded function for your set-top-
box/satellite receiver.
This remote is designed to operate different types of
set-top-box/satellite systems. You must first program
the remote to match the remote system of your set-
top-box/satellite systems (refer to pages 37-38 for pre-
codes).
1.
Turn ON your set-top-box/satellite systems.
2.
Aim the remote control at the front of your set-top-
box/satellite systems.
3.
To switch to set-top-box/satellite (STB) pre-coded
mode, use the SOURCE ACCESS buttons (
³
or
´
)
on the remote control to position the LED light to
the corresponding selection.
4.
Hold down the ENT button on the remote and enter
the four digit preset code that matches your set-
top-box/satellite receiver as shown on page 37-38.
Release the ENT button.
The indicator light will
flash 3 times if the code was accepted.
5.
Aim the remote at the set-top-box/satellite receiver
and press the POWER button.
The remote will turn
off your set-top-box/satellite receiver when the
correct four digit preset code is entered.
When this
occurs, the remote control is programmed for your
set-top-box/satellite receiver.
If the set-top-
box/satellite receiver does not turn off, try a
different four digit preset code.
6.
The remote will now control your set-top-
box/satellite receiver.
NOTE:
1. If your set-top-box/satellite receiver
cannot be operated after performing the
above procedures, your set-top-box/
satellite receiver code has not been
precoded into the remote.
2. In the unlikely event that your set-top-
box/satellite receiver cannot be operated
after performing the above procedures,
please consult your set-top-box/satellite
receiver operating guide.
3.
The remote control will remember the
codes you have programmed until the
batteries are removed from the from the
remote control.
After replacing the
batteries repeat the entire programming
procedure as stated above.
¹
PRE-CODED SET-TOP-BOX/SATELLITE
RECEIVER buttons
These buttons transmit the chosen pre-coded set-
top-box/satellite codes.
À
EXCLUSIVE TV buttons
These buttons are for operating the TV.
MY Satellite RECEIVER/
SET-TOP-BOX CODE IS:
NOTE:
Refer to instruction manual of the Set-Top-
Box/Satellite Receiver for operation of the
buttons exclusively for the Set-Top-
Box/Satellite Receiver.
The Remote Control for Set-Top-Box/Satellite Receiver
Functions
The Remote Control
¹
À
¹
À
¹
À
¹
¹