Hitachi 60V715 Owners Guide - Page 36

Using Your Remote, To Control Vcr/pvr Functions

Get Hitachi 60V715 - 60inch Rear Projection TV PDF manuals and user guides View all Hitachi 60V715 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

USING YOUR REMOTE TO CONTROL VCR/PVR FUNCTIONS Operating the precoded function for your VCR/PVR (Personal Video Recorder). This remote is designed to operate different types of VCRs/PVRs. You must first program the remote to match the remote system of your VCR/PVR (refer to pages 39-40 for pre-codes). 1. Turn ON your VCR/PVR. 2. Aim the remote control at the front of your VCR/PVR. 3. To switch to VCR/PVR pre-coded mode, use the SOURCE ACCESS buttons (̇ , ̈) on the remote control to position the LED light to the corresponding selection. 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your VCR/PVR, as shown on pages 3940. Release the ENT button. The indicator light will flash 3 times if the code was accepted. 5. Aim the remote at the VCR/PVR and press the POWER button. The remote will turn off your PVR when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your VCR/PVR. If the VCR/PVR does not turn off, try a different four digit preset code. 6. The remote will now control your VCR/PVR. NOTES: 1. If your PVR cannot be operated after performing the above procedures, your PVR's code has not been precoded into the remote. 2. In the unlikely event that your PVR cannot be operated after performing the above procedures, please consult your PVR operating guide. 3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. 4. VCR precode library is included in the PVR mode. Default device for this mode is Hitachi VCR. 5. INFO, GUIDE and LC (Last Channel) buttons are for PVR devices, not for VCR. ቢ PRECODED VCR/PVR Buttons These buttons transmit the chosen precoded VCR/PVR codes. ባ EXCLUSIVE TV Buttons These buttons are for operating the TV. ቢ ቢ ባ GUIDE ቢ C.C. ባ ቢ ቢ THE REMOTE CONTROL MY VCR/PVR CODE IS: NOTE: Refer to instruction manual of the VCR/PVR for operation of the buttons exclusively for the VCR/PVR. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
36
USING YOUR REMOTE
TO CONTROL VCR/PVR FUNCTIONS
Operating the precoded function for your VCR/PVR (Personal Video Recorder).
This remote is designed to operate different types of VCRs/PVRs.
You must first program the remote to match the remote system of
your VCR/PVR (refer to pages 39-40 for pre-codes).
1.
Turn ON your VCR/PVR.
2.
Aim the remote control at the front of your VCR/PVR.
3.
To switch to VCR/PVR pre-coded mode, use the SOURCE ACCESS buttons (
³
,
´
) on the remote control to position the LED light
to the corresponding selection.
4.
Hold down the ENT button on the remote and enter the four digit preset code that matches your VCR/PVR, as shown on pages 39-
40.
Release the ENT button.
The indicator light will flash 3 times if the code was accepted.
5.
Aim the remote at the VCR/PVR and press the POWER button.
The remote will turn off your PVR when the correct four digit pre-
set code is entered.
When this occurs, the remote control is programmed for your VCR/PVR.
If the VCR/PVR does not turn off,
try a different four digit preset code.
6.
The remote will now control your VCR/PVR.
NOTES:
1.
If your PVR cannot be operated after performing the
above procedures, your PVR’s code has not been
precoded into the remote.
2.
In the unlikely event that your PVR cannot be operated
after performing the above procedures, please consult
your PVR operating guide.
3.
The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control.
After replacing the batteries repeat the
entire programming procedure as stated above.
4.
VCR precode library is included in the PVR mode.
Default device for this mode is Hitachi VCR.
5.
INFO, GUIDE and LC (Last Channel) buttons are for PVR
devices, not for VCR.
±
PRECODED VCR/PVR Buttons
These buttons transmit the chosen precoded VCR/PVR
codes.
²
EXCLUSIVE TV Buttons
These buttons are for operating the TV.
GUIDE
±
²
±
²
C.C.
±
±
±
MY VCR/PVR CODE IS:
NOTE:
Refer to instruction manual of the VCR/PVR for operation of the buttons exclusively for the VCR/PVR.
THE REMOTE CONTROL