Hitachi 60V715 Owners Guide - Page 72

If Power Is Connected Before The Lamp Cover Is Installed, The Power Will, Be Off And The Lamp

Get Hitachi 60V715 - 60inch Rear Projection TV PDF manuals and user guides View all Hitachi 60V715 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

LAMP REPLACEMENT LAMP REPLACEMENT 6. Without installing the lamp cover, the power will be off and the Lamp Indicator will flash (see page 8). Be sure to install the lamp cover by re-engaging the two clips and tighten the screws before turning the power on, otherwise it may cause unusual colors. SCREW LAMP COVER PHILLIP HEAD SCREW DRIVER NOTE: IF POWER IS CONNECTED BEFORE THE LAMP COVER IS INSTALLED, THE POWER WILL BE OFF AND THE LAMP INDICATOR WILL FLASH (SEE PAGE 8 ). 7. Install the front cover as shown below. Put the front cover back in and align the snap on quick connect then push inwards holding the left and right side of the front cover until you hear a snap. Push the other snap on gently to make a good fit. 8. Plug power cord into AC outlet and turn on the main power switch. 120V NOTE: This product contains lead and a lamp that contains mercury. Dispose of this product and its lamp in accordance with applicable environmental laws. For lamp recycling and disposal information, go to www.lamprecycle.org. For product recycling and disposal information, contact your local government agency or the Electronic Industries Alliance at www.eiae.org (in the US) or the Electronic Product Stewardship Canada at www.epsc.ca (in Canada). For more information, call "1-800-HITACHI." 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
72
LAMP REPLACEMENT
6.
Without installing the lamp cover, the power will be off and the Lamp Indicator will flash (see page 8).
Be sure to install the lamp
cover by re-engaging the two clips and tighten the screws before turning the power on, otherwise it may cause unusual colors.
SCREW
LAMP COVER
PHILLIP HEAD
SCREW DRIVER
NOTE:
IF POWER IS CONNECTED BEFORE THE LAMP COVER IS INSTALLED, THE POWER WILL
BE OFF AND THE LAMP INDICATOR WILL FLASH (SEE PAGE 8 ).
7.
Install the front cover as shown below.
Put the front cover back in and align the snap on quick connect then push inwards hold-
ing the left and right side of the front cover until you hear a snap.
Push the other snap on gently to make a good fit.
8.
Plug power cord into AC outlet and turn on the main power switch.
120V
NOTE:
This product contains lead and a lamp that contains mercury.
Dispose of this product and its lamp in accordance with
applicable environmental laws.
For lamp recycling and disposal information, go to www.lamprecycle.org.
For product
recycling and disposal information, contact your local government agency or the Electronic Industries Alliance at
www.eiae.org (in the US) or the Electronic Product Stewardship Canada at www.epsc.ca (in Canada).
For more information, call “1-800-HITACHI.”
LAMP REPLACEMENT