Hitachi CP-SX635 User Manual
Hitachi CP-SX635 - SXGA+ LCD Projector Manual
 |
UPC - 050585151529
View all Hitachi CP-SX635 manuals
Add to My Manuals
Save this manual to your list of manuals |
Hitachi CP-SX635 manual content summary:
- Hitachi CP-SX635 | User Manual - Page 1
Projector CP-SX635 User's Manual (detailed) - Operating Guide Thank you for purchasing this projector. WARNING ►Before using this product, please read the "User's Manual - Safety Guide" and related manuals • VESA and DDC are trademarks of the Video Electronics Standard Association. • DVI is a - Hitachi CP-SX635 | User Manual - Page 2
17 Information, Service Searching an input signal 18 C.C. (Closed Caption) menu . . 62 Selecting an aspect ratio 18 Display, Mode, Channel Adjusting the zoom and focus. . . . . . 19 Maintenance 63 Adjusting the lens shift 19 Lamp 63 Using the automatic adjustment feature. . . 19 Air - Hitachi CP-SX635 | User Manual - Page 3
distance. Moreover, the projector has the following features to extend its potentiality for broad use. ü The HDMI port can support various image equipment which see the "Contents of package" in the "User's Manual (concise)" which is a book. Your projector should come with the items shown there. - Hitachi CP-SX635 | User Manual - Page 4
use, since it is too hot. ►Do not look into the lens or vents while the lamp is on, since the strong light is not good for your eyes. ►Do not grab the front cover to hold the projector up, since the projector may drop down. ►Do not handle the elevator knobs without holding - Hitachi CP-SX635 | User Manual - Page 5
69) (5) TEMP indicator (&69) (6) LAMP indicator (&69) Rear panel (6) (5) CONTROL port (&10) (9) HDMI port (&10) (10) VIDEO port (&10) (11) S-VIDEO port (&10) (12) COMPONENT (Y, CB/PB, CR/ projector from falling down, since it is not designed for it. ►Use the shutdown switch only when the projector - Hitachi CP-SX635 | User Manual - Page 6
remote control port (&15) (30) Battery cover (&13) (31) Battery holder (&13) (32) Frequency switch (&14) (32) (2) (1) LASER INDICATOR STANDBY/ON VIDEO RGB MY SOURCE/ DOC.CAMERA SEARCH BLANK LASER (8) (14) (9) (3) ASPECT PUSH ENTER PAGE UP PAGE DOWN ESC MENU RESET POSITION AUTO - Hitachi CP-SX635 | User Manual - Page 7
hot objects such as heaters. • Do not place anything near the projector lens or vents, or on top of the projector. • Do not place anything that may be sucked into or stick to the vents on the bottom of the projector. This projector has some intake vents also on the bottom. ►Do not place the - Hitachi CP-SX635 | User Manual - Page 8
) (b) Projection distance (±10%) (c) Screen height (±10%), when the vertical lens shift (&19) is set full upward. On a horizontal surface (b) (a) • Keep a space of 30 cm or more between the sides of the projector and other objects such as walls. • Consult with your dealer before a special - Hitachi CP-SX635 | User Manual - Page 9
Y VIDEO RGB1 CB/PB RGB2 M1-D Setting up Adjusting the projectCoR/rPR's elevator When the place to put the projector is attached to the security bar on the projector. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool. LAN WARNING ► - Hitachi CP-SX635 | User Manual - Page 10
manuals for devices before connecting them to the projector. IN1 AUDIO IN2 LAN RGB OUT RGB1 Y VIDEO CB/PB CR/PR S-VIDEO R L R L AUDIO IN3 AUDIO IN4 AUDIO projector. ►Use appropriate accessory or designated cables. Ask your dealer about nonaccessory cables which may be required a specific - Hitachi CP-SX635 | User Manual - Page 11
laptop PC to the projector, be sure to activate the PC's external RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT display.) For details on how this is done, please refer to the instruction manual of the corresponding laptop PC. • When the picture resolution is changed on - Hitachi CP-SX635 | User Manual - Page 12
connector of the power cord to the AC IN (AC inlet) of the projector. 2. Firmly plug the power cord's plug into the outlet. AC IN Connector in fire and/or electrical shock. • Only use the power cord that came with the projector. If it is damaged, contact your dealer to get a new one. • Only plug - Hitachi CP-SX635 | User Manual - Page 13
button STANDBY/ON LAINSDEIRCATOR RGB VIDEO MDYOSCO.CUARMCEER/ A SEARCH LASER people. The laser beam can cause vision problems. CAUTION ►Use of controls or adjustments HITACHI MAXELL, Part No.LR6 or R6P) according to their plus and minus terminals as indicated in the remote control. 3. Replace - Hitachi CP-SX635 | User Manual - Page 14
(such as from an inverter fluorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights. 30º 30º Approx SERVICE item of OPTION menu (&48) of the projector to be controlled should be set to the same mode as the remote control. To set the mode - Hitachi CP-SX635 | User Manual - Page 15
IN1 remOoUTte VcIDEoOntrol connects with the REMOTE CONTROL port on AUDIOIN2 the back of the CB/PB CR/PR projector via an audio cable with 3.5 diameter stereo mini S-VIDEO plugs. R L AUDIO IN3 R L AUDIO IN4 AUDIO OUT When the remote control signal is hard to reach surely to the - Hitachi CP-SX635 | User Manual - Page 16
the projector or the remote control. LASER INDICATOR STANDBY/ON VIDEO projector. WARNING ►A strong light is emitted when the projector's power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector's openings. ►Do not touch around the lamp - Hitachi CP-SX635 | User Manual - Page 17
● When the projector is in the standby mode, the volume can supports the C.C. feature (62). Selecting an input signal 1. Press the INPUT button on the projector. Each time you press the button, the projector switches its input from the current port as below. RGB 1 RGB 2 HDMI VIDEO S-VIDEO - Hitachi CP-SX635 | User Manual - Page 18
button on the remote control to select an input for video signal. Each time you press the button, the projector switches its video input port as below. COMPONENT (Y, CB/PB, CR/PR) S-VIDEO VIDEO LASER INDICATOR STANDBY/ON VIDEO RGB MY SOURCE/ DOC.CAMERA SEARCH BLANK LASER ● While TURN - Hitachi CP-SX635 | User Manual - Page 19
Lens LASER shift cover INDICATOR VIDEO RGB MY SOURCE/ DOC.CAMERA SEARCH LEFT BLANK RIGLAHSERT Using the automatic adjustment feature use this feature. A dark video signal and s-video signal The video for the VIDEO FORMAT item component video signal is performed for a video signal, a certain - Hitachi CP-SX635 | User Manual - Page 20
on a video signal, s-video signal or component video signal, some to select AUTO or MANUAL operation, and press the projector is inclined to near ±30 degree or over, this function may not work well. ● When the vertical lens shift is not set fully upward (not set fully downward for the optional lens - Hitachi CP-SX635 | User Manual - Page 21
INDICATOR POSITION button again. STANDBY/ON VIDEO RGB To exit from the MAGNIFY mode and restore the screen to normal projector automatically exits from the FREEZE mode when some control buttons are pressed. ● If the projector continues projecting a still image for a long time, the LCD - Hitachi CP-SX635 | User Manual - Page 22
return to the input signal screen, press the BLANK button again. LASER INDICATOR STANDBY/ON VIDEO RGB MY SOURCE/ DOC.CAMERA SEARCH BLANK LASER ● T he projector automatically exits from the BLANK mode when some control buttons are pressed. ASPECT NOTE • The sound is not connected with the - Hitachi CP-SX635 | User Manual - Page 23
the menu position, use the cursor buttons after pressing the POSITION button. While the projector is displaying any menu, the MENU button on the projector works as the cursor buttons. LASER INDICATOR STANDBY/ON VIDEO RGB MY SOURCE/ DOC.CAMERA SEARCH BLANK LASER ASPECT PUSH ENTER PAGE UP - Hitachi CP-SX635 | User Manual - Page 24
, H PHASE, VOLUME etc.) cannot be reset. ● In the Advanced MENU, when you want to return to the previous display, press the ◄ cursor button on the projector or remote control, or the ESC button on the remote control. 5. Press the MENU button on the remote control again to close the menu and - Hitachi CP-SX635 | User Manual - Page 25
be performed. Select an item using the ▲/▼ cursor buttons on the projector or remote control. Then perform it according to the following table. EASY AUTO KEYSTONE EXECUTE KEYSTONE KEYSTONE Description Using the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE menu (30 - Hitachi CP-SX635 | User Manual - Page 26
the sharpness. See the SHARPNESS item in PICTURE menu (28). Using the ◄/► buttons turns off/on the whisper mode. See the WHISPER item in SETUP menu (37). Using the ◄/► buttons switches the mode for mirror status. See the MIRROR item in SETUP menu (37). Performing this item resets all of the EASY - Hitachi CP-SX635 | User Manual - Page 27
an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or the ENTER button on or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of - Hitachi CP-SX635 | User Manual - Page 28
dialog to aid you in adjusting the OFFSET and GAIN of the selected mode. OFFSET adjustments change the color intensity on the whole tones of the Strong ó Weak • This item can be selected only for a video signal, s-video, component video or HDMI signal. Using the ▲/▼ buttons adjusts the tint. Greenish - Hitachi CP-SX635 | User Manual - Page 29
iris control mode. PRESENTATION ó THEATER ó TURN OFF ACTIVE IRIS MY MEMORY PRESENTATION THEATER TURN OFF Feature The active iris screen may flicker when the PRESENTATION or THEATER modes are selected. If this occurs select TURN OFF. This projector has 4 memories for adjustment data (for all - Hitachi CP-SX635 | User Manual - Page 30
the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER REAL For a Video signal, S-video signal or Component video signal 4:3 ó 16:9 ó 16:10 ó 14:9 ó REAL For no signal 4:3 (fixed) • The NORMAL mode keeps the original - Hitachi CP-SX635 | User Manual - Page 31
an RGB signal or a component video signal. (except 480i@60, 576i feature. feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting. For a video signal and s-video signal The video for the VIDEO FORMAT item video is performed for a video signal, a certain extra - Hitachi CP-SX635 | User Manual - Page 32
the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button buttons switches the noise reduction mode. HIGH ó MID ó LOW VIDEO NR 3D-YCS • This function is performed only for the VIDEO or S-VIDEO input, and for 480i - Hitachi CP-SX635 | User Manual - Page 33
is performed only for a video signal from the VIDEO port or the S-VIDEO port. • The AUTO mode automatically selects the optimum mode. • The AUTO operation may the HDMI signal mode. AUTO ó NORMAL ó ENHANCED HDMI AUTO NORMAL ENHANCED Feature Selecting the optimum mode automatically. Suitable for - Hitachi CP-SX635 | User Manual - Page 34
the ▲/▼ buttons to select the RGB input signal type. AUTO ó SYNC ON G OFF • Selecting the AUTO mode allows you to input a sync on G signal or component signal from the port. • In the AUTO mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so - Hitachi CP-SX635 | User Manual - Page 35
RGB1 and RGB2 input signals can be set on this projector. (1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button. The RESOLUTION menu will be displayed. (2) In the RESOLUTION menu select the resolution you wish to display using the ▲/▼ buttons. Selecting AUTO will - Hitachi CP-SX635 | User Manual - Page 36
the level (about ±3°), this function may not work. • When the projector is inclined to near ±30 degree or over, this function may not work well. • When the vertical lens shift is not set fully upward (not set fully downward for the optional lens type FL-601 only (47)), this function may not work - Hitachi CP-SX635 | User Manual - Page 37
lens type FL-601 only (47)), this function may not work well. • This function will be unavailable when the Transition Detector is on (53). Using the ▲/▼ buttons turns off/on the whisper mode be displayed when projector is restarted ó HDMI STANDBY ó VIDEO ó S-VIDEO ó COMPONENT(Y, CB/PB, CR/PR - Hitachi CP-SX635 | User Manual - Page 38
on the projector or remote control, and press the ► cursor button on the projector or VIDEO, S-VIDEO or COMPONENT port, the C.C. (Closed Caption) is automatically activated, if the C.C. is set to AUTO in the DISPLAY item of the C.C. menu and the signal from the input port supports the C.C. feature - Hitachi CP-SX635 | User Manual - Page 39
item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the ▲/▼ buttons switches the mode for the blank screen. The blank screen is a screen for the temporarily blanking feature (22). It is displayed - Hitachi CP-SX635 | User Manual - Page 40
Item Description Using the ▲/▼ buttons switches the mode for the start-up screen. The start-up screen is a screen displayed when no signal or an unsuitable signal is detected. MyScreen ó ORIGINAL ó TURN OFF START UP MyScreen ORIGINAL TURN OFF Feature Screen can be registered by the MyScreen item - Hitachi CP-SX635 | User Manual - Page 41
SCREEN menu (continued) SCREEN menu Item Description MyScreen This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure. 1. S electing this item - Hitachi CP-SX635 | User Manual - Page 42
aspect ratio displayed by changing The indication of the PICTURE MODE displayed by changing The indication of the ACTIVE IRIS displayed freezing. Do not mistake freezing for a malfunction (21). Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN - Hitachi CP-SX635 | User Manual - Page 43
SCREEN menu (continued) SCREEN menu Item TEMPLATE Description Using ▲/▼ buttons switches the mode for the template screen. The selected template pattern can be displayed when the MY BUTTON allocated to the TEMPLATE function is pressed (46). DOT-LINE4 ó - Hitachi CP-SX635 | User Manual - Page 44
the ceiling this feature will not function properly so select the TURN OFF. • This function will be unavailable when the Transition Detector is on (53). AUTO ON Using the ▲/▼ buttons turns on/off the AUTO ON function. TURN ON TURN OFF When set to the TURN ON, the lamp in projector will be - Hitachi CP-SX635 | User Manual - Page 45
► button of the projector displays a dialog. To reset the lamp time, select the RESET using the ▲ button. RESET ï CANCEL • Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp. • For the lamp replacement, see the section "Lamp" (63, 64). FILTER - Hitachi CP-SX635 | User Manual - Page 46
AUTO ADJUST GHOST FILTER MESSAGE LENS TYPE FACTORY RESET INFORMATION REMOTE FREQ. REMOTE RECEIV. KEY LOCK FANSPEED Using the ▲/▼ buttons switches the rotation speed of the cooling fans. The HIGH is the mode for use at highlands etc. Note that the projector is noisier when the HIGH is - Hitachi CP-SX635 | User Manual - Page 47
of the mode. When the DISABLE is selected, the automatic adjustment feature is disabled. FINE ó FAST ó DISABLE SERVICE (continued) of the projector. • Please be careful with the operating environment of the projector and the condition of the air filter. LENS TYPE Select the lens type currently - Hitachi CP-SX635 | User Manual - Page 48
Item SERVICE (continued) Description KEY LOCK Using the ▲/▼ buttons turns on/off the key lock feature. When TURN ON is selected, the buttons on the projector except return to the initial setting. Note that the items LAMP TIME, FILTER TIME, LANGUAGE, SECURITY and NETWORK settings are not reset. RESET - Hitachi CP-SX635 | User Manual - Page 49
menu (continued) OPTION menu Item SECURITY Description This projector is equipped with security functions. User registration is required before using the security functions. Please contact your local dealer. 1. Using Security Features 1.1 Inputting the PASSWORD 1.1-1 Use the ▲/▼ buttons on the - Hitachi CP-SX635 | User Manual - Page 50
and hold the INPUT button for 3 seconds while pressing the ► button on the projector. The 10 digit Inquiring Code will be displayed. • If there is no key 10 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed. SECURITY (continued) 2. Using the - Hitachi CP-SX635 | User Manual - Page 51
the 10 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed. ENTER PASSWORD BOX (large) 3. Using the PIN LOCK Function PIN LOCK is a function which prevents the projector from being used unless a registered Code is input. 3.1 Registering the PIN - Hitachi CP-SX635 | User Manual - Page 52
displayed. • If there is no key input for about 5 minutes while the Inquiring Code is displayed, the projector will turn off. 3.3-2 Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed. (continued on next page) 52 - Hitachi CP-SX635 | User Manual - Page 53
current angle and mirror setting will be recorded. • This feature may not function properly if the projector is not in a stable position when TURN ON is selected for about 5 minutes, the lamp will turn off. This function will activate only when the projector is started after the power switch - Hitachi CP-SX635 | User Manual - Page 54
Code will be displayed inside the BOX. 4.4-3 Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed. ENTER PASSWORD BOX (large) 5. Using the MY TEXT PASSWORD function This item allows you to display your own message - Hitachi CP-SX635 | User Manual - Page 55
on the START UP screen and the INPUTINFORMATION- when the INFORMATION on the SERVICE menu is chosen (48). • This function is available only when the MY Pressing the ENTER button on the remote control or INPUT button on the projector will return to the MY TEXT PASSWORD on/off menu. When the PASSWORD - Hitachi CP-SX635 | User Manual - Page 56
digit inquiring code will be displayed inside the box. (3) C ontact your dealer with the 10 digit inquiring code. Your PASSWORD will be sent after your user registration information is confirmed. 56 - Hitachi CP-SX635 | User Manual - Page 57
projector may cause trouble projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. See the User's Manual - Network Guide the item. SETUP DHCP (Dynamic Host Configuration Protocol) Use the ▲/▼ buttons to turn DHCP on - Hitachi CP-SX635 | User Manual - Page 58
Use the buttons to enter the Year (last two digits), Month, Date, Hour and Minute. • The projector will override this setting and retrieve DATE AND TIME information from the Time server when SNTP is enabled. ( Date/Time Settings of the User's Manual - Network Guide) (continued on next page) 58 - Hitachi CP-SX635 | User Manual - Page 59
ENTER or INPUT button, 1 character or all characters will be erased. The PROJECTOR NAME can be input up to 64 characters. (3) To change an already screen and press the ENTER or INPUT button. To revert to the previous PROJECTOR NAME without saving changes, move the cursor to the CANCEL on screen and - Hitachi CP-SX635 | User Manual - Page 60
. The application software "PJImage" is required to store image(s) into the projector. Use the ▲/▼ buttons to select an item which is a still image by the MY IMAGE ( MY IMAGE (Still Image Transfer) Display of the User's Manual - Network Guide) and the ► or ENTER button to display the image. • The - Hitachi CP-SX635 | User Manual - Page 61
Replace the battery suitably (66). • IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY indicate "0.0.0.0" when DHCP is ON and the projector has not gotten address from DHCP server. Executing this item restarts and initializes the network functions. Choose the RESTART using the button ►. SERVICE - Hitachi CP-SX635 | User Manual - Page 62
format video or 480i@60 format component video source supporting C.C. feature to utilize MODE setting from following options using ▲/▼buttons. CAPTIONS ó TEXT CAPTIONS: Display Closed Caption TEXT: D isplay Text data, which is for additional information such as news reports or a TV program guide - Hitachi CP-SX635 | User Manual - Page 63
you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, contact your dealer and tell the lamp type number. Type number = DT00873 Replacing the lamp 1. Turn the projector off, and unplug the power cord. Allow the projector to cool for at least 45 - Hitachi CP-SX635 | User Manual - Page 64
if the lamp's bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken. • Do not use the projector with the lamp cover removed. At the lamp replacing, make - Hitachi CP-SX635 | User Manual - Page 65
the air filter. An air Filter cover filter of specified type will come together with a replacement lamp for this projector. 1.Turn the projector off, and unplug the power cord. Allow the projector to sufficiently cool down. 2.Use a vacuum cleaner on and around the filter cover. Filter cover - Hitachi CP-SX635 | User Manual - Page 66
come up. Remove the battery. 5. Replace the battery with a new HITACHI MAXELLL, Part No. CR2032 or CR2032H the projector's upside up. (2)While lifting the side of the projector closer to the lens, press replacing the battery. ( Date/Time Settings in the User's Manual (detailed) - Network Guide) 66 - Hitachi CP-SX635 | User Manual - Page 67
off, and unplug the power cord. Allow the projector to cool sufficiently. 2. After making sure that the projector is cool adequately, lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens directly with your hand. Caring for the cabinet and remote control - Hitachi CP-SX635 | User Manual - Page 68
of the input signal is not within the specified range. Please confirm the specs for your projector or the signal source specs. An improper signal is input. Please confirm the specs for your projector or the signal source specs. The internal temperature is rising. Please turn the power off, and allow - Hitachi CP-SX635 | User Manual - Page 69
the instructions within the table. If the same indication is displayed after the remedy, or if an indication other than the following is displayed, please contact your dealer or service company. POWER TEMP LAMP indicator indicator indicator Description Lighting Turned Turned The projector is - Hitachi CP-SX635 | User Manual - Page 70
in Green for approx. 3 seconds Turned off Turned off At least 1 "Power ON" schedule is saved to the projector. (Please refer to the User's Manual-Network Guide: Schedule Settings for more information.) NOTE • When the interior portion has become overheated, for safety purposes, the power source - Hitachi CP-SX635 | User Manual - Page 71
projector cool down enough. 3. Some setting may be wrong. Please use the FACTORY RESET function of the SERVICE item in the OPTION menu (48) to reset all settings to factory default. Then, if the problem the signal source device by referring to the manual of the source device. The input changeover - Hitachi CP-SX635 | User Manual - Page 72
Troubleshooting RCA audio 10 cable or stereo mini cable. The lens cover is attached. Remove the lens cover. 3, 16 The signal cables are not projector are not harmonized. Turn off the both equipment, and turn on them again - The signal format on the HDMI is not supported. Check the video - Hitachi CP-SX635 | User Manual - Page 73
approaching the end of its product lifetime. Replace the lamp. Either the focus and/or horizontal phase settings are not properly adjusted. Adjust the focus using the focus ring, and/or H PHASE using the menu function. The lens is dirty or misty. Clean the lens referring to the section "Caring for - Hitachi CP-SX635 | User Manual - Page 74
"Troubleshooting" and run through the suggested checks. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied. Specifications Item Product name Liquid Panel size Crystal Drive system Panel Pixels Lens Lamp Audio - Hitachi CP-SX635 | User Manual - Page 75
418 [unit: mm] 75 139 154 319 LAN HDMI AUDIO IN1 AUDIO IN2 RGB OUT RGB1 Y VIDEO CB/PB CR/PR S-VIDEO R L AUDIO IN3 R L AUDIO IN4 AUDIO OUT RGB2 G/Y B/CB/PB R/CR/PR H V REMOTE CONTROL USB CONTROL AC IN I O Specifications (continued) Specifications
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
 |
 |
1
Projector
CP-SX635
User's Manual (detailed) – Operating Guide
Thank you for purchasing this projector.
►Before using this product, please read the "User's Manual -
Safety Guide" and related manuals to ensure the proper use of this product.
After reading them, store them in a safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
Various symbols are used in this manual. The meanings of these symbols are
described below.
About this manual
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.
Please refer to the pages written following this symbol.
• Windows
®
is a registered trademark of Microsoft Corporation in the U.S. and/or
other countries.
• VESA and DDC are trademarks of the Video Electronics Standard Association.
• DVI is a trademark of Digital Display Working Group.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC.
All other trademarks are the properties of their respective owners.