Hitachi CP-WX1100 Lens Replacement Manual
Hitachi CP-WX1100 Manual
View all Hitachi CP-WX1100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Hitachi CP-WX1100 manual content summary:
- Hitachi CP-WX1100 | Lens Replacement Manual - Page 1
ENGLISH Lens Replacement Manual ■ Lens replacement should be performed by a service engineer. ■ When changing the lens, place the LCD projector right way up on a horizontal surface. Do not change the lens with the projector facing upwards or downwards or when the projector is suspended. Attaching - Hitachi CP-WX1100 | Lens Replacement Manual - Page 2
the center position. Refer to the user manual supplied with the LCD projector for instructions on how to return the lens shift to the center position. Protector 8. Removing the lens (2) Support the lens and remove the lens from the LCD projector. Place the detached lens on a soft cloth or similar - Hitachi CP-WX1100 | Lens Replacement Manual - Page 3
projector before changing the lens. ■ Return the lens shift to the center position. Refer to the user manual supplied with the LCD projector for instructions on how to return the lens to adjust the flange-back. (1) Use the LCD projector remote control or control panel to adjust the surrounding focus - Hitachi CP-WX1100 | Lens Replacement Manual - Page 4
- Hitachi CP-WX1100 | Lens Replacement Manual - Page 5
DEUTSCH Objektiv-Montageanweisungen ■ Die Montage bzw. der Austausch des Objektivs ist vom Kundendienstpersonal durchzuführen. ■ Den LCD-Projektor zum Montieren/Austauschen des Objektivs mit der Oberseite nach oben auf eine ebene Fläche stellen. Das Objektiv nicht montieren/austauschen, wenn der - Hitachi CP-WX1100 | Lens Replacement Manual - Page 6
Ersetzen des Objektivs SD-804/LL-805/UL-806 durch das Objektiv USL-801/SL-802/SL-803 1. Abmontieren von Teilen an der Haupteinheit (1) Den Frontring abdrehen. Vorsicht: ■ Vor dem Auswechseln des Objektivs unbedingt den LCD-Projektor ausschalten. ■ Das Objektiv per Objektivverschiebung wieder in - Hitachi CP-WX1100 | Lens Replacement Manual - Page 7
Auflagemaß-Einstellung (nur beim USL-801) (Das Objektiv USL-801 wird ohne die beiden Blenden und Schutzabdeckungen geliefert.) 1. Schärfe im Umfeld Wenn nach Montage des Objektivs USL-801 ein Bild projiziert wird, kann das Umfeld im Vergleich zur Bildmitte unscharf erscheinen. Mitte In diesem - Hitachi CP-WX1100 | Lens Replacement Manual - Page 8
- Hitachi CP-WX1100 | Lens Replacement Manual - Page 9
4 6 64-4-4 ιέοτ ֯Ϩϯν Ωϟοϓ ϩοΫϨόʔ πϝ ϩοΫϨόʔ 4 6 4-4- ͷΈ ϒϥΠϯμ πϝ 4-4- ͷΈ - Hitachi CP-WX1100 | Lens Replacement Manual - Page 10
4 6- ͔Β 64-4-4 ϩοΫϨόʔ 4-4- ͷΈ ϒϥΠϯμ πϝ 4-4- ͷΈ ʲҙʳ 64-4- 4 4 6 4 - Hitachi CP-WX1100 | Lens Replacement Manual - Page 11
64- ͷΈʳ ʢ64 64 ॴݸ '# ௐ૭ ॴݸ Ϩϯζຊମ - Hitachi CP-WX1100 | Lens Replacement Manual - Page 12
QR77621A
6. Attaching the lens (2)
Support the lens installed in the LCD
projector and move the lock lever on the
projector as far as it will go to the right
(until the lock lever clicks into the locked
position).
Caution:
■
To prevent the lens from falling off,
after attaching the lens, check that
it is securely mounted and that the
lock lever does not move.
Lens Replacement Manual
■
Lens replacement should be performed by a service engineer.
■
When changing the lens, place the LCD projector right way up on a horizontal surface. Do not change the lens with the projector facing upwards or downwards or when
the projector is suspended.
Attaching the SD-804/LL-805/UL-806 Lens When Unpacking the LCD Projector
1.
Preparing to attach the lens (1)
Take the lens adapter supplied with the
LCD projector and mount it so that the
connector on the lens is aligned with the
socket of the lens adapter.
Caution:
■
Be careful not to touch the surface
of the lens.
■
Do not touch the socket of the lens
adapter or subject it to impact as
this may lead to malfunction.
■
Do not hold the lens by the lens
shade as this may lead to injury or malfunction
.
■
Be sure to remove the tape
fi
xing the hexagonal screw on the lens.
■
Be sure to remove the lens cap. Installing the lens in the LCD projector with the
lens cap on may lead to malfunction.
2.
Preparing to attach the lens (2)
Using the hexagon wrench supplied
with the LCD projector, attach the lens
adapter with the four hexagon screws on
the lens.
Connect the connector on the lens to the
socket of the lens adapter.
3. Preparing to attach the lens (3)
Unscrew the front ring from the LCD
projector and remove the cap.
4. Preparing to attach the lens (4)
Lift off the front cover to remove it.
5. Preparing to attach the lens (1)
Make sure that the terminal on the lens
and the terminal on the LCD projector are
aligned.
Support the lens with the lens adapter
attached and install it in the LCD
projector so that the adapter rib
fi
ts into
the groove of the projector.
Caution:
■
Do not hold the lens by the lens
shade as this may lead to injury or
malfunction.
■
Take care to avoid hitting the surface of the lens on the LCD projector when
attaching the lens as this may lead to malfunction.
7. Assembling the main unit parts (1)
Insert the two catches on the front cover
into the LCD projector body to attach the
front cover.
8. Assembling the main unit parts (2)
Have the blind sheet supplied with the
lens ready and mount it on the lens
shade.
Mount the blind sheet with its matte side
facing out.
9. Assembling the main unit parts (3)
Screw on the front ring.
Caution:
■
Take care not to get the blind sheet
trapped when
fi
tting the front ring
as this may lead to malfunction.
10. Lens attachment is completed.
Attaching the USL-801/SL-802/SL-803 Lens When Unpacking the LCD Projector
1. Lens attachment is completed.
Follow the procedures in step 1 through
step 6 for Attaching the SD-804/LL-805/
UL-806 Lens and install the lens in the
LCD projector.
3. Attaching the optional parts (2)
(SL-802/SL-803 only)
Rotate the attached blinder to the
underside of the lens and mount the
second blinder on the lens shade in the
same way.
Engage the two catches on these
blinders.
4. Assembling the main unit parts (1)
Insert the two catches on the front cover
into the LCD projector body to attach the
front cover.
5. Assembling the main unit parts (2)
Screw on the front ring.
Caution:
■
Take care not to get the blind sheet
trapped when
fi
tting the front ring
as this may lead to malfunction.
6. Attaching the optional parts (3)
(SL-802/SL-803 only)
Have the two protectors supplied with the
lens ready and insert the
fi
rst protector
between the front ring and the lens.
7. Attaching the optional parts (4)
(SL-802/SL-803 only)
Rotate the attached protector to the
underside of the lens and insert the
second protector in the same way
between the front ring and the lens.
Engage the two catches on the protector.
8. Lens attachment is completed.
2. Attaching the optional parts (1)
(SL-802/SL-803 only)
Have the two blinders supplied with the
lens ready and mount the
fi
rst blinder on
the lens shade.
Socket
Connector
Hexagon wrench
Front cover
Cap
Front ring
Terminal on projector
Terminal on lens
Lens shade
Groove
Rib
Lock lever
Lock lever
Front cover
Catch
Catches
Blind sheet
Lens shade
Front ring
Front cover
Catch
Catches
Front ring
Catch
Blinder
Protector
Front ring
Catch
Protector
Lens adapter
Socket
Connector
Lens shade
ENGLISH
Blinder
Lens shade
Caution:
■
When using the USL-801 lens, the
edges of the projected image may
appear dark or shadows may be visible.
If this happens, use the lens shift
function to adjust the position of the
projected image.