Hitachi CP-WX1100 Network Guide

Hitachi CP-WX1100 Manual

Get Hitachi CP-WX1100 PDF manuals and user guides View all Hitachi CP-WX1100 manuals
Add to My Manuals
Save this manual to your list of manuals

Hitachi CP-WX1100 manual content summary:

  • Hitachi CP-WX1100 | Network Guide - Page 1
    Projector CP-X10000/CP-WX11000/CP-SX12000 User's Manual (detailed) Network Guide Thank you for purchasing this projector. This projector has the network function that brings you the following main features. Web control The projector can be controlled and monitored by a web browser software on your
  • Hitachi CP-WX1100 | Network Guide - Page 2
    Required equipment preparation 4 2.2 Manual network connection setting 5 2.2.1 Equipments connection 5 2.2.2 Network settings 5 2.2.3 "Internet Option" setting 8 2.2.4 Check connection 9 3. Management with Web browser software 10 3.1 Configuring and controlling the projector via a web browser
  • Hitachi CP-WX1100 | Network Guide - Page 3
    and controlling via a web browser You can adjust or control the projector via a network from a web browser on a PC that is connected web browser and it offers the menus to configure the network settings, monitor the projector and so on. 1.2 MY IMAGE (Still image Transfer) Display Image files can be
  • Hitachi CP-WX1100 | Network Guide - Page 4
    connection and network setting 2. Equipment connection and network setting 2.1 Required equipment preparation The following equipments are required to connect the projector to your PC through the network. PC : 1) equipped with the network feature 2) installed a web browser software ( 11) LAN cable
  • Hitachi CP-WX1100 | Network Guide - Page 5
    2. Equipment connection and network setting 2.2 Manual network connection setting 2.2.1 Equipments connection Connect the projector and PC with a LAN cable. * Before connecting with an existing network, contact the network administrator. Next, please check the PC setting as explained below. 2.2.2
  • Hitachi CP-WX1100 | Network Guide - Page 6
    2. Equipment connection and network setting 2.2 Manual network connection setting (continued) 5) Open "Local Area Connection Properties" window you use for network device. (Fig. 2.2.2.c) Fig. 2.2.2.c "Local Area Connection Properties" window 6) Set used protocol
  • Hitachi CP-WX1100 | Network Guide - Page 7
    2. Equipment connection and network setting 2.2 Manual network connection setting (continued) [About IP address] ■ Setting manually The Network address portion included in the IP address set into your PC should be common with projector's one. And the entire IP address in the PC should not be
  • Hitachi CP-WX1100 | Network Guide - Page 8
    2. Equipment connection and network setting 2.2 Manual network connection setting (continued) 2.2.3 "Internet Option" setting 1) Click "Internet Options" in "Network and Internet Connections" window (Fig. 2.2.3.a) to open "Internet Properties" window. (Fig.2.2.3.b) Click Fig. 2.2.3.a "
  • Hitachi CP-WX1100 | Network Guide - Page 9
    connection and network setting 2.2 Manual network connection setting (continued) Fig. 2.2.3.c "Local Area Network (LAN) Settings" window 3) Uncheck all boxes in "Local Area Network (LAN) Settings" window. (Fig. 2.2.3.c) 2.2.4 Check connection Check PC and projector are connected properly here. If
  • Hitachi CP-WX1100 | Network Guide - Page 10
    to specified e-mail addresses when the projector requires maintenance or has encountered an error. ( 33) 3.3 Projector Management using SNMP This projector is SNMP (Simple Network Management Protocol) compliant, allowing you to monitor it from a remote location using SNMP software. In addition, the
  • Hitachi CP-WX1100 | Network Guide - Page 11
    SSL (Secure Socket Layer) if you are using Windows® XP Service Pack 2 or earlier versions of Microsoft® Windows®. Please specify "https://" when you enter the IP address of the projector on the web browser. You can't communicate the projector using SSL on Windows Vista®. • It is recommended that all
  • Hitachi CP-WX1100 | Network Guide - Page 12
    and User ID. The following chart describes the differences between Administrator and User IDs. Item Description Network Information Displays the projector's current network configuration settings. Network Settings Displays and configures network settings. Port Settings Displays and configures
  • Hitachi CP-WX1100 | Network Guide - Page 13
    via a web browser (continued) 3.1.1 Logon Refer to the following for configuring or controlling the projector via a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter "http://192.168.1.10/" into the address bar of the web browser and press "Enter" key or
  • Hitachi CP-WX1100 | Network Guide - Page 14
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) 3.1.2 Network Information All screen drawings in this manual are shown when you logon with the Administrator ID. Any functions that are available only for the Administrator will not be
  • Hitachi CP-WX1100 | Network Guide - Page 15
    gures the subnet mask when DHCP is disabled. Configures the default gateway when DHCP is disabled. Configures the name of the projector. The length of the Projector Name can be up to 64 alphanumeric characters. Only alphabets, numbers and following symbols can be used and space Configures the location
  • Hitachi CP-WX1100 | Network Guide - Page 16
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) 3.1.4 Port Settings Displays and configures communication port settings. Item Description Network Control Port1 (Port:23) Configures command control port 1 (
  • Hitachi CP-WX1100 | Network Guide - Page 17
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) Item SNMP Port Port open Trap address SMTP Port Port open Network Bridge Port Port Number Daisy Chain Port Port Number
  • Hitachi CP-WX1100 | Network Guide - Page 18
    Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) 3.1.5 Mail Settings Displays and con clicking [Send Test Mail]. • If you connect the projector to an existing network, consult a network administrator before setting server addresses. 18
  • Hitachi CP-WX1100 | Network Guide - Page 19
    . ( OPTION menu in the User's Manual (detailed) - Operating Guide) The Power switch is turned on. (Off → standby mode) The SNMP access is detected from the invalid SNMP community. Refer to "Troubleshooting" in the User's Manual (detailed) - Operating Guide for further detailed explanation of Error
  • Hitachi CP-WX1100 | Network Guide - Page 20
    displayed on the projector screen. The e-mail will be sent when the filter timer exceeds 2000, 5000 or 10000 hours based on the configuration. No notification e-mail will be sent if the FILTER MESSAGE is set to OFF. ( OPTION menu in the User's Manual (detailed) - Operating Guide) • Lamp Time Alarm is
  • Hitachi CP-WX1100 | Network Guide - Page 21
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) 3.1.7 Schedule Settings Displays and configures schedule settings. Item Daily Sunday Monday Tuesday Wednesday Thursday Friday Saturday Specific date No.1 Specific
  • Hitachi CP-WX1100 | Network Guide - Page 22
    list. Click [Reset] button to delete all commands and reset the schedule settings from the schedule list. NOTE • After the projector is moved, check the date and time set for the projector before configuring the schedules. Strong shock may make the date and time settings ( 23) get out of tune. 22
  • Hitachi CP-WX1100 | Network Guide - Page 23
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) 3.1.8 Date/Time Settings Displays and configures the date and time settings. Item Current Date Current Time Daylight Savings Time Start
  • Hitachi CP-WX1100 | Network Guide - Page 24
    existing network, consult a network administrator before setting server addresses. • To enable the SNTP function, the time difference must be set. • The projector will retrieve Date and Time information from the time server and override time settings when SNTP is enabled. • The internal clock's time
  • Hitachi CP-WX1100 | Network Guide - Page 25
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) 3.1.9 Security Settings Displays and configures passwords and other security settings. Item Administrator authority Administrator ID Administrator Password Re-enter Administrator
  • Hitachi CP-WX1100 | Network Guide - Page 26
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) Item Network Control Authentication Password Re-enter Authentication Password SNMP Community name Description Configures the Authentication password for the command
  • Hitachi CP-WX1100 | Network Guide - Page 27
    changes the value manually. In that case, please refresh the page by clicking [Refresh] button. Controls the projector. Item Main Power setting. Adjusts the focus setting. Adjusts the vertical lens shift. Adjusts the horizontal lens shift. Saves / Loads the Lens Memory data. Turns the P by P on /
  • Hitachi CP-WX1100 | Network Guide - Page 28
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) Item Picture (continue) Gamma Color Temp Color Tint Sharpness Active Iris Active Iris - Manual MyMemory Save MyMemory Recall Image Aspect Over Scan V Position H Position H Phase H Size
  • Hitachi CP-WX1100 | Network Guide - Page 29
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) Item Description Setup Auto Keystone Execute Keystone V Keystone H Performs the automatic keystone distortion setting. Adjusts the vertical keystone distortion setting. Adjusts
  • Hitachi CP-WX1100 | Network Guide - Page 30
    timer to shut off the projector when no signal is detected. Remote Receiv. Front Turns the remote receiv. front function on/off. Remote Receiv. Rear Turns the remote receiv. rear function on/off. Remote Receiv. Top Turns the remote receiv. top function on/off. Remote Freq. Normal Turns the remote
  • Hitachi CP-WX1100 | Network Guide - Page 31
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) 3.1.11 Projector Status Displays the current projector status. Item Error Status Lamp Time Filter Time Power Status Input Status Blank On/Off Freeze Shutter Description Displays the
  • Hitachi CP-WX1100 | Network Guide - Page 32
    in order to activate new configuration settings. NOTE • Restarting requires you to re-log on in order to further control or configure the projector via a web browser. Wait 1 minute or more after clicking [Restart] button to log on again. • The Logon menu ( 13) is displayed after restarting the
  • Hitachi CP-WX1100 | Network Guide - Page 33
    or detected an error. NOTE • Up to five e-mail addresses can be specified. • The projector may be not able to send e-mail if the projector suddenly loses power. Mail Settings ( 18) To use the projector's e-mail alert function, please configure the following items through a web browser. Example: If the
  • Hitachi CP-WX1100 | Network Guide - Page 34
    ] button to save the settings. Failure/Warning e-mails are formatted as follows: Subject line : Text : Date Time IP Address MAC Address
  • Hitachi CP-WX1100 | Network Guide - Page 35
    . NOTE • It is recommended that SNMP functions be carried out by a network administrator. • SNMP management software must be installed on the computer to monitor the projector via SNMP. SNMP Settings ( 16) Configure the following items via a web browser to use SNMP. Example: If the IP address of the
  • Hitachi CP-WX1100 | Network Guide - Page 36
    software 3.4 Event Scheduling The scheduling function enables to setup scheduled events including power on / power off. It enables to be "self-management" projector. NOTE • You can schedule the following control events: Power ON/OFF, Input Source and Transferred Image Display. • The power on / off
  • Hitachi CP-WX1100 | Network Guide - Page 37
    for approx. 3 seconds when at least 1 "Power ON" schedule is saved. • When the schedule function is used, the power cord must be connected to the projector and the outlet and the power switch must be turned on, [ | ]. The schedule function does not work when the power switch is turned off, [O] or
  • Hitachi CP-WX1100 | Network Guide - Page 38
    Time setting can be adjusted via a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter "http://192.168.1.10/" into the address "Internal clock battery" section of the User's Manual (concise). • The internal clock's time may not remain accurate. Using SNTP
  • Hitachi CP-WX1100 | Network Guide - Page 39
    requires an exclusive application for your PC. You can download it from the Hitachi web site (http://hitachi.us/digitalmedia or http://www. hitachidigitalmedia.com). Refer to the manual for the application for instructions. To display the transferred image, select the MY IMAGE item in the NETWORK
  • Hitachi CP-WX1100 | Network Guide - Page 40
    (Still Image Transfer) Display (continued) Configure the following items from a web browser when MY IMAGE is used. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter "http://192.168.1.10/" into the address bar of the web browser. 2) Enter the Administrator ID and password
  • Hitachi CP-WX1100 | Network Guide - Page 41
    function. Command Control Settings ( 16) Configure the following items from a web browser when command control is used. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter "http://192.168.1.10/" into the address bar of the web browser. 2) Enter the Administrator ID and
  • Hitachi CP-WX1100 | Network Guide - Page 42
    3. Management with Web browser software 3.6 Command Control via the Network (continued) When the authentication setting is enabled, the following settings are required. ( 25) 7) Click [Security Settings] on the main menu. 8) Click [Network Control] and enter the desired authentication password. *
  • Hitachi CP-WX1100 | Network Guide - Page 43
    3. Management with Web browser software 3.6 Command Control via the Network (continued) Command Format Command formats differ among the different communication ports. ● TCP #23 You can use the RS-232C commands without any changes. The reply data format is the same as the RS-232C commands. However,
  • Hitachi CP-WX1100 | Network Guide - Page 44
    Reply 0x15 Connection ID 1 byte Connection ID 1 byte Reply 0x1C Error code 2 bytes Reply Data 0x1D 2 bytes Reply Status code 0x1F 2 bytes Reply 0x1F Authentication Error code 0x04 0x00 Connection ID 1 byte
  • Hitachi CP-WX1100 | Network Guide - Page 45
    the Authentication Password is set to "password" and the random 8 bytes are "a572f60c". 1) Select the projector. 2) Receive the random 8 bytes "a572f60c" from the projector. 3) Bind the random 8 bytes "a572f60c" and the Authentication Password "password" and it becomes "a572f60cpassword". 4) Digest
  • Hitachi CP-WX1100 | Network Guide - Page 46
    LAN port with a LAN cable, for Ethernet communication. 2) Connect the projector's CONTROL OUT port and the device's RS-232C port with an RS-232C cable, for RS-232C communication. NOTE • Before connecting the devices, read the manuals for the devices to ensure the connection. For RS-232C connection
  • Hitachi CP-WX1100 | Network Guide - Page 47
    cation of the RS232C port of the connected device. ( Operating Guide - OPTION menu - SERVICE - COMMUNICATION - SERIAL IN SETTING/SERIAL OUT SETTING) Item BAUD the NETWORK BRIDGE function, send the data from the computer to the projector with using the Network Bridge Port that is configured in the "
  • Hitachi CP-WX1100 | Network Guide - Page 48
    when the NETWORK BRIDGE is selected for the COMMUNICATION TYPE. ( Operating Guide - OPTION menu - SERVICE - COMMUNICATION - TRANSMISSION METHOD) HALF-DUPLEX  FULL-DUPLEX 3.7.4.1 HALF-DUPLEX This method lets the projector make two way communication, but only one direction, either transmitting or
  • Hitachi CP-WX1100 | Network Guide - Page 49
    from an external devise and the RESPONSE LIMIT TIME is set to OFF, the projector can receive the data from the computer and send it out to an external as the default setting. 3.7.4.2 FULL-DUPLEX This method lets the projector make two way communication, transmitting and receiving data at the same
  • Hitachi CP-WX1100 | Network Guide - Page 50
    family models (ask your dealer for details) are equipped with the DAISY CHAIN function. Using the DAISY CHAIN function can simultaneously control multiple projectors connected to a shared RS-232C bus, from a computer. RS-232C cable (cross) [Power ON] CONTROL IN port LAN cable [Power ON] Computer
  • Hitachi CP-WX1100 | Network Guide - Page 51
    NONE/ODD/EVEN 8 bit (fixed) 1 bit (fixed) 1 bit (fixed) 3) Using the COMMUNICATION TYPE menu, select the DAISY CHAIN for each projector. ( Operating Guide - OPTION menu - SERVICE - COMMUNICATION - COMMUNICATION TYPE) NOTE • The baud rate and parity of the CONTROL IN port do not need to be set up when
  • Hitachi CP-WX1100 | Network Guide - Page 52
    simultaneously, set up the COMMUNICATION GROUP and COMMUNICATION ID for each projector. Use the COMMUNICATION GROUP menu and COMMUNICATION ID menu to set up them. ( Operating Guide - OPTION menu - SERVICE - COMMUNICATION - COMMUNICATION GROUP / COMMUNICATION ID) NOTE • The COMMUNICATION GROUP is set
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
1
•
Microsoft
®
and Internet Explorer
®
, Windows
®
, Windows Vista
®
are registered
trademark of Microsoft Corporation in the U.S. and/or other countries.
• JavaScript
®
is a registered trademark of Sun microsystems, Inc.
• DVI is a trademark of Digital Display Working Group.
•
HDMI, the HDMI logo and High-De
fi
nition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC.
•
Trademark PJLink is a trademark applied
for trademark rights in Japan, the United
States of America and other countries and areas.
All other trademarks are the properties of their respective owners.
Projector
CP-X10000/CP-WX11000/CP-SX12000
User's Manual (detailed)
Network Guide
Thank you for purchasing this projector.
This projector has the network function that brings you the following main features.
►
Before using this product, be sure to read all manuals for this
product.
After reading them, store them in a safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
9
Web control
The projector can be controlled and monitored by a web browser software on
your PC, which can help you to setup and maintain the projector.
9
MY IMAGE (Still Image Transfer) Display
The projector can display still images that are transferred via the network.
This manual is only intended to explain Network function only.
For safety, operations or any other issues, refer to the Safety Guide and User’s
Manual (concise and detailed).
Trademark acknowledgment