Hitachi CPX885 User Manual
Hitachi CPX885 - XGA LCD Projector Manual
 |
View all Hitachi CPX885 manuals
Add to My Manuals
Save this manual to your list of manuals |
Hitachi CPX885 manual content summary:
- Hitachi CPX885 | User Manual - Page 1
LCD Projector CP-X880/CP-X885 USER'S MANUAL Vol.1 (Basic) Thank you for purchasing this projector. WARNING • Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a - Hitachi CPX885 | User Manual - Page 2
packing material for future reshipment. Projector (with Lens Cap) Power cord (US Type) Power cord (UK Type) Power cord (Europe Type) Liquid Crystal Projector CP-X880/CP-X885 (CP-X880W/CP-X885W) USER'S MANUAL Vol.1 Basic Please read this user's manual thoroughly to ensure correct usage through - Hitachi CPX885 | User Manual - Page 3
SHOCK. Please adhere to the following safety guidelines to insure safe operation of the projector: • Only plug the power cord into outlets rated for other devices you will be using to the projector. ʙ 2 Insert the batteries into the remote control 3 Connect the power cord (1) Connect - Hitachi CPX885 | User Manual - Page 4
FOCUS RESET ZOOM MENU TENP LANP FOCUS button ZOOM button MENU button Vol.2 LAMP indicator STANDBY/ON button Control Panel Vol.2 TEMP indicator Elevator feet Elevator screw Lens cap Lens Air filter Remote sensor Elevator button COMPONENT VIDEO port - Hitachi CPX885 | User Manual - Page 5
THE REMOTE CONTROL LASER INDICATOR VIDEO button STANDBY/ON button FOCUS buttons BLANK button LASER INDICATOR STANDBY/ON VIDEO RGB PUSH ENTER ESC MENU RESET POSITION AUTO PinP MAGNIFY ON VOLUME OFF FREEZE MUTE WIRELESS KEYSTONE ONE TOUCH REMOTE CONTROL port RGB - Hitachi CPX885 | User Manual - Page 6
SETTING UP THE PROJECTOR CAUTION • Install the projector in a suitable environment according to instructions of the accompanying manual "SAFETY INSTRUCTIONS" and this manual. • If you press the elevator buttons without holding the projector, the projector might crash down, overturn, smash your - Hitachi CPX885 | User Manual - Page 7
from the projector to the screen (±10%) b:Distance from the lens center to the bottom of the screen (±10%) c:Distance from the lens center ) 366 (9.3) 547 (13.9) 0 (0) 180 (457) If 16:9 aspect ratio 16 9 c Lens center b a Side view Screen Size [inch (m)] 30 (0.8) 40 (1.0) 50 (1.3) 60 (1.5) 70 - Hitachi CPX885 | User Manual - Page 8
manual and the separate "SAFETY INSTRUCTIONS". ATTENTION Precautions to observe when connecting other devices to the projector • Whenever attempting to connect other devices to the projector, please thoroughly read the manual and/or projector. Refer to the "TECHNICAL" of the USER'S MANUAL (Vol.2) - Hitachi CPX885 | User Manual - Page 9
Audio cable (Stereo mini) Wired remote control signal input REMOTE CONTROL Audio cable (Stereo mini) * Before using the BNC port, change RGB input to component video input on the BNC menu item of the INPUT menu. NOTE About Plug-and-Play Capability • This projector is compatible with VESA DDC - Hitachi CPX885 | User Manual - Page 10
simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer. DVI " RGB R/CR/PR G/Y RGB OUT B/Ca/Pa H BNC CONTROL V CR/PR Ca/Pa REMOTE CONTROL Y COMPONENT VIIDEO R-AUDIO IN-L VIDEO IN 1 2 # S-VIDEO IN - Hitachi CPX885 | User Manual - Page 11
/PR Ca/Pa Y COMPONENT VIIDEO RGB RGB OUT R/CR/PR G/Y B/Ca/Pa H """" BNC CONTROL V " R-AUDIO IN-L VIDEO IN 1 2 # S-VIDEO IN AUDIO IN AUDIO OUT USB " # DVI Input " DVI CR/PR Ca/Pa REMOTE CONTROL Y COMPONENT VIIDEO RGB R/CR/PR G/Y RGB OUT B/Ca/Pa H CONTROL V BNC R-AUDIO IN - Hitachi CPX885 | User Manual - Page 12
Connecting to a VCR DVI RGB R/CR/PR G/Y RGB OUT B/Ca/Pa H CONTROL V REMOTE CONTROL CR/PR " Ca/Pa " Y COMPONENT VIIDEO " ### R-AUDIO IN-L VIDEO IN 1 2 $ S-VIDEO IN BNC AUDIO IN AUDIO OUT USB " # $ REMOTE CONTROL DVI CR/PR Ca/Pa Y COMPONENT VIIDEO RGB R/CR/PR G/Y RGB OUT - Hitachi CPX885 | User Manual - Page 13
arrow. 2 Insert the batteries Align and insert the two AA batteries (that came with the projector) according to their plus and minus terminals (as indicated in the remote control). 3 Close the battery cover Replace the battery cover in the direction of the arrow and snap it back into place - Hitachi CPX885 | User Manual - Page 14
for an extended period. • Replace the batteries whenever the remote control starts to malfunction. • When strong light, such as direct sunlight or light from an extremely close range (such as from an inverter fluorescent lamp), hits the projector's remote sensor, the remote control may cease to - Hitachi CPX885 | User Manual - Page 15
lens. LASER INDICATOR STANDBY/ON VIDEO RGB FOCUS ZOOM UP PAGE DOWN BLANK LASER Control panel RGB BNC DVI INPUT VIDEO S-VIDEO COMPONENT STANDBY/ON KEYSTONE ONE TOUCH FOCUS RESET ZOOM MENU TENP LANP 1 Make sure that the power cord is firmly and correctly connected to the projector - Hitachi CPX885 | User Manual - Page 16
button Press this button to toggle between the VIDEO devices connected to VIDEO IN, S-VIDEO IN and COMPONENT VIDEO. As illustrated below, each time you press the VIDEO button, the projector switches between VIDEO IN, S-VIDEO IN and COMPONENT VIDEO. Select the signal you wish to project. • When BNC - Hitachi CPX885 | User Manual - Page 17
for STANDBY/ON approximately 5 seconds. 2 Press the STANDBY/ON button again (control panel or remote control) Press the STANDBY/ON button again while the "Power off?" message is visible. The projector lamp goes off and starts cooling down. While cooling, the STANDBY/ON indicator flashes orange - Hitachi CPX885 | User Manual - Page 18
VOLUME 16 ASPECT PUSH ENTER ESC MENU RESET POSITION AUTO PinP MAGNIFY ON VOLUME OFF FREEZE MUTE WIRELESS KEYSTONE ONE TOUCH 2 Use the lever switch / to adjust the volume Press the VOLUME button again to close the dialog and complete this operation. (Even if you don't do anything, the - Hitachi CPX885 | User Manual - Page 19
LASER INDICATOR STANDBY/ON VIDEO RGB FOCUS ZOOM UP PAGE DOWN BLANK LASER ASPECT PUSH ENTER ESC MENU RESET POSITION AUTO PinP MAGNIFY the position, press the RESET button during adjustment. Press the POSITION button again to close the dialog and complete this operation. (Even if you don - Hitachi CPX885 | User Manual - Page 20
Press the AUTO button AUTO ASPECT PUSH ENTER ESC MENU RESET POSITION AUTO PinP MAGNIFY ON VOLUME OFF FREEZE MUTE WIRELESS KEYSTONE This feature is available only if VIDEO is set to AUTO in the INPUT menu. NOTE The automatic adjustment operation requires approximately 10 seconds. Also, - Hitachi CPX885 | User Manual - Page 21
KEYSTONE DISTORTIONS ASPECT PUSH ENTER ESC MENU RESET POSITION AUTO PinP MAGNIFY ON VOLUME OFF / to correct distortion Press the KEYSTONE button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds - Hitachi CPX885 | User Manual - Page 22
the input signal's state.) NOTE The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT, AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state. FREEZING THE SCREEN PUSH ENTER ESC MENU RESET POSITION AUTO PinP MAGNIFY ON VOLUME - Hitachi CPX885 | User Manual - Page 23
PAGE DOWN BLANK LASER ASPECT PUSH ENTER ESC MENU RESET POSITION AUTO PinP MAGNIFY ON VOLUME OFF FREEZE MUTE BNC(RGB) DVI COMPONENT VIDEO S-VIDEO VIDEO • When BNC (COMPONENT) is selected: RGB BNC(COMPONENT) DVI COMPONENT VIDEO S-VIDEO VIDEO (2) Automatic adjustment: In - Hitachi CPX885 | User Manual - Page 24
BLANK LASER (HDTV signals : 1125i (1035i/1080i), 750p) ASPECT 4:3 16:9 VIDEO IN, S-VIDEO IN, COMPONENT VIDEO (Non-HDTV signals : 525i, 525p,625i) ASPECT 4:3 16:9 SMALL PUSH ENTER ESC MENU RESET POSITION AUTO PinP TEMPORARILY BLANKING THE SCREEN FOCUS ZOOM UP PAGE DOWN BLANK LASER - Hitachi CPX885 | User Manual - Page 25
VIDEO RGB FOCUS ZOOM UP PAGE DOWN BLANK LASER ASPECT PUSH ENTER ESC MENU RESET POSITION AUTO PinP MAGNIFY ON VOLUME OFF FREEZE MUTE WIRELESS KEYSTONE ONE TOUCH 1 Press the MENU button MENU The menu display appears on the screen. The projector finish your operation. Alternatively, - Hitachi CPX885 | User Manual - Page 26
manuals of the device you will connect. • Do not unplug the connector cables while the computer is operating. LASER INDICATOR STANDBY/ON VIDEO projector's USB terminal to a PC using a USB cable. The functions in the table below can be controlled. Available Functions Remote Control Operation lamp - Hitachi CPX885 | User Manual - Page 27
the user. Before replacing the lamp, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp. WARNING The LCD projector uses a glass lamp bulb - Hitachi CPX885 | User Manual - Page 28
. • Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly. • When the lamp has been replaced after the message of "CHANGE THE LAMP .....THE POWER WILL - Hitachi CPX885 | User Manual - Page 29
Lamps" (Vol.2 ) for details.) 1 Turn off the projector, and unplug the power cord 2 Apply a vacuum cleaner to the top of the air filter cover to clean the air filter Air Filter Cover 3 Turn on the projector, and use the menu to reset the filter timer • To reset the air filter timer - Hitachi CPX885 | User Manual - Page 30
cord. Prepare a new air filter (one specified for your projector) 2 Remove the air filter cover and air filter 3 Insert the new filter, and replace the filter cover 4 Turn on the projector power, and using the menu, reset the filter timer • To reset the lamp timer, from the OPTION menu, select - Hitachi CPX885 | User Manual - Page 31
lens : Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens directly with your hand. Caring for the cabinet and remote the unit. Please carefully read "Safety Instructions" in this manual, in order to care for your projector correctly. • Do not use cleaners or - Hitachi CPX885 | User Manual - Page 32
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
 |
 |
1
LCD Projector CP-X880/CP-X885
USER'S MANUAL
USER'S MANUAL
Vol.1 (Basic)
Page
PROJECTOR FEATURES
................
2
PREPARATIONS
..............................
2
PART NAMES
...................................
4
SETTING UP
THE PROJECTOR
............................
6
CONNECTING
YOUR DEVICES
................................
8
USING THE REMOTE
CONTROL
.......................................
13
TURNING ON THE POWER
...........
15
TURNING OFF THE POWER
.........
17
ADJUSTING THE VOLUME
...........
18
TEMPORARILY MUTING
THE SOUND
....................................
18
ADJUSTING THE POSITION
..........
19
USING THE AUTOMATIC
ADJUSTMENT FEATURE
..............
20
CORRECTING KEYSTONE
DISTORTIONS
................................
21
Page
USING THE MAGNIFY
FEATURE
........................................
22
FREEZING THE SCREEN
..............
22
ADJUSTING SCREEN WITH
ONE-TOUCH
...................................
23
SELECTING THE ASPECT
RATIO
..............................................
24
TEMPORARILY BLANKING
THE SCREEN
..................................
24
DISPLAYING CHILD WINDOW
(P. IN. P: Picture in Picture)
..........
24
USING THE MENU
FUNCTIONS
....................................
25
OPERATING THE PC SCREEN
.....
26
THE LAMP
......................................
27
THE AIR FILTER
.............................
29
OTHER CARE
.................................
31
CONTENTS
Thank you for purchasing this projector.
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without express
written authority.
TRADEMARK ACKNOWLEDGEMENT :
• PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation.
• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc.
• VESA and SVGA are trademarks of the Video Electronics Standard Association.
• Windows is a registered trademark of Microsoft Corporation.
• All other trademarks are the property of their respective owners.
NOTE
WARNING
• Please read the accompanying manual “SAFETY
INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct
usage through understanding. After reading, store this instruction manual in a
safe place for future reference.