Hitachi W6VB3SD Operating Instructions

Hitachi W6VB3SD - 2,600 RPM SUPERDRIVE Collated Screw System Manual

Hitachi W6VB3SD manual content summary:

  • Hitachi W6VB3SD | Operating Instructions - Page 1
    HITACHI SuperDrive Auto-feed Screw System WARRANTY HITACHI SuperDrive tools and system components are 1 Call 1-800-706-7337 or your sales rep. for replacement parts. Operating Instructions For SuperDrive 75 Series OPERATION 1. Check Driver Bit to make sure it is in good condition. • If it is
  • Hitachi W6VB3SD | Operating Instructions - Page 2
    -7337 or your sales rep. for replacement parts. Screws are miss-driving. What causes mis-drives? 1. Broken or worn out driver bit. 2. Operating the SuperDrive too fast. 3. Not lifting the SuperDrive off the work surface before driving the next screw. 4. Roller bearing is slipping during the indexing
  • 1
  • 2

Operating Instructions
OPERATION
1. Check Driver Bit to make sure it is in good con-
dition.
• If it is broken or worn out, install a new one.
2.
IMPORTANT!
Make sure the forward-reverse
switch is in the forward position.
3. Insert a strip of screws into the feed track. Pull
it through and insert the front into the index mod-
ule until the first screw is in driving position in the
center of the nose piece. See Figure 1.
FIGURE 1.
4. Adjust the nosepiece so there is a 1/8” to 1/4”
gap between nose piece and tip of screw.
• Tighten the nosepiece screw securely. See
Figure 2.
5. Follow instructions on the sticker.
Push slider in
to adjust.
Then turn knob until it locks.
FIGURE 2.
FIGURE 3.
6. Turn on the motor before starting to drive
screws.
• The motor can be locked to the ON position.
HITACHI SuperDrive Auto-feed Screw System
WARRANTY
HITACHI SuperDrive tools and system components are warranted to the original purchaser at retail to be free from defects
in material and workmanship one year from the date of purchase.
The warranty shall only cover defects and not normal wear and tear, which occurs with use.
HITACHI SuperDrive assumes no responsibility whatsoever for malfunctions, failures or defects resulting from misuse,
abuse, neglect, alteration or modification. SuperDrive makes no warranty and shall not be liable as to the fitness of its tools
or fasteners for any particular uses or applications. No other warranties, representations or promises as to the quality or
performance of the SuperDrive fastening tool other than those contained herein are made.
ANY IMPLIED WARRANTY GRANTED UNDER STATE LAW, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO DURATION TO THE EXPRESS WARRANTY GRANTED HEREUNDER. SUPER-
DRIVE IN NO EVENT SHALL BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
For SuperDrive 75 Series
Appx. 1/4”
Call 1-800-706-7337 or your sales rep. for replacement parts.
PARTS LIST - 75 SERIES TOOL
QTY
725414
MODULE (GREEN DOT)
1
725415
SPRING (GREEN) 1.7mm
1
725413
NOSEPIECE FLAT HEAD SCREW
M4x10mm
1
725470
NOSEPIECE SUBFLOOR AND
METAL-TO-METAL
1
725471
NOSEPIECE DECK/DRYWALL
1
725425
END PLATE FOR 75
1
725424
WING SCREW FOR END PLATE
1
725423
BODY HEX SOCKET CAP SCREW
M4x8
1
725422
BODY HEX SOCKET CAP SCREW
M4x10
2
725416
RETAINER SCREW - M3x6
2
725416
RETAINER FOR MODULE 3mm
2
725427
BRACKET FOR FEEDTRACK
2
725428
FEED TRACK HEX SOCKET SCREW
1/4”-20 x 7.4mm
5
725426
FEED TRACK
1
725432
TUBE FOR END PLATE
1
DEPTH ADJUSTMENT PARTS
QTY
725472
DEPTH CONTROL RETAINER
1
725474
DEPTH CONTROL SPRING
1
725473
DEPTH CONTROL ADJUSTMENT
WHEEL
1
725475
SNAP E RING E2
1
EXTENSION PARTS
QTY
725476
EXTENSION 19”
1
729430
BIT EXTENSION
1
729431
HANDLE ASSEMBLY
1
725413
725470
725471
725414 (GREEN DOT)
725415 (GREEN)
725475
725473
725472
725416
725474
725424
725422
725425
725432
725428
725427
725423
725476
725430
725431
725426
725416