Honeywell 4219 Installation Guide

N8924V1

5/01 Rev. B

4219

Wired Zone Expander Module

INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

This module adds up to eight end-of-line resistor supervised

zones to compatible control/communicators via the control’s

keypad wiring.

The module may be mounted within the control’s cabinet (if

room permits), or remotely.

If mounted remotely, there are

provisions to tamper protect the unit.

Communication to

the module is supervised so that it cannot be disconnected

from the keypad wiring without detection by the control.

If

the wiring is cut, a tamper alarm or signal will result, to

indicate that this device (and possibly other similarly

connected devices) has become inoperative.

INSTALLATION

1.

Power

should

be

disconnected

before proceeding.

2.

Be sure to mount the 4219 before

making any wire connections.

When the module is mounted remotely, holes on the back of

the module’s housing permit it to be mounted horizontally

or vertically.

Wires can exit from the side or the breakout

on the back of its housing.

For tamper protection, attach

the tamper magnet (provided) (Figure 1) to the module

inside cover.

Place the tamper jumper (Figure 2) into its

lower position.

Affix the connections label that accompanies

the module to the inside of the module’s cover.

When the

installation is complete, put the modules cover on.

The

magnet attached to the cover, positioned near the reed

switch, will cause a tamper signal to be sent to the control if

the cover is removed.

When the module is to be mounted inside the control’s

cabinet, mount it horizontally to the raised tabs at the back

of the cabinet.

Insert self-tapping screws (provided) in two

adjacent raised tabs at the back of the cabinet.

Leave the

heads projecting 1/8”.

Hang the module on the screw heads

via two slotted holes on the back of the module’s housing.

When the module is installed in the control’s cabinet, it

need not be tamper protected.

Place the tamper jumper

(Figure 2) in the upper position.

Affix the connections label

that accompanies the module to the inside of the control’s

cover.

S

ee the control’s installation and setup guide for additional

information.

CONNECTIONS AND SETTINGS

Make protection zone connections to the module’s 12-

position terminal block TB1.

Each zone that is used must

have a 1000-ohm end-of-line resistor connected across the

end of its loop, as shown in Figure 1.

C

E

For CE installations ADEMCO N6361

EMI

suppression

bead

is

required.

Refer to the N6361 installation guide for

wire routing instructions.

1. INSERT BOTTOM TABS FIRST.

2. ENGAGE TOP WITH CLIP.

4219-002-V0

Figure 1.

Tamper Magnet Installation

If a zone is not programmed, the resistor need not be used.

The method of programming each zone for the type of alarm

and reporting code to the central monitoring station varies

with the control to which the module is connected.

Refer to

the Installation and Setup Guide for that control unit.

Set the DIP Switch to one of 16 addresses, as shown in

Figure 3, so the control can identify the module and

communicate with it properly.

The address to be set is

determined by the particular control to be used, and the

control’s installation instructions must be consulted.

As

shipped, the DIP Switch is set for an address of “0”.

Zone A can be set for fast response time of 10ms to an open

circuit, if desired, by setting position 1 of the DIP Switch to

“OFF”.

As shipped, it is set to “ON” for a response time of

300ms, as shown in the table below.

All of the module’s

other protection zones have a nominal response time of

300ms.

Connections to the control’s keypad wiring points can be

made via 4-terminal block TB2 or the 4-pin plug (wire color

connections are the same).

SPECIFICATIONS

Physical

6-7/16”W x 4-1/4”H x 1-1/4” D

(163mm x 108mm x 32mm)

Electrical

Input Voltage:

12VDC

(from

control’s

remote

keypad connection points)

Current:

30mA

Honeywell 4219 Installation Guide

Honeywell 4219 - Ademco 8 Zone Expander Manual

Honeywell 4219 manual content summary: