Honeywell 6150V Installation Guide

K0022V2 12/01

Rev. B

ADEMCO 6150V & 6160V

Voice Remote Keypads

INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

The ADEMCO 6150V and ADEMCO 6160V are addressable

remote keypads designed for use with ADEMCO control

panels and provide the following features:

•

Backlit Display

•

Voice Chime

•

Programmable Function

Keys

•

Voice Status

•

Message Center

•

Built-in Sounder

Notes:

•

When used with the ADEMCO VISTA-15P/VISTA-

20P control panels, address 16 must be assigned to

the first keypad.

Additional keypads must be

assigned to address 17 – 23.

Refer to Setting The

Keypad Options.

•

Keypad keys are continuously backlit for convenience.

•

Permanent display backlighting is an option on some

controls (refer to the control panel’s instructions for

details).

•

Voice Chime should only be enabled when used with

control panels that support the "chime by zone" mode

(e.g., VISTA-15P/VISTA-20P).

This mode must be

enabled at the control panel.

Refer to the control panel's

installation and setup guide for information on how to

program the chime mode.

•

Use only zone descriptors supported by this

keypad.

If using zone descriptors not supported

by this keypad, you must turn voice status and

voice chime off.

Table 1 is a list of applicable zone

descriptors and index entries.

Refer to

the control

panel’s installation and setup guide for information

about how to program zone descriptors.

KEYPAD DISPLAYS AND LEDS

The keypads have the following display features:

Model

Fixed

Word

Display

2-Line

Alpha

Display

2-Digit

Zone

Identifier

Custom

Zone

Descriptors

6150V

X

X

6160V

X

X

The following table identifies the keypad’s LEDs and

associated functions:

LED

Function

ARMED

Lights red when the system is armed in any mode.

READY

Lights green when the system is "ready" to be

armed.

MESSAGE

Flashes red when message waiting or lights red

(steady) when in record mode.

PROGRAMMABLE FUNCTION KEYS

The keypad's programmable function keys [A, B, C] are

normally used for keypad panic functions, but they can be

programmed for other special functions instead.

If they are

programmed for other special functions, the associated

keypad key pairs still provide the respective panic alarm (if

programmed).

Refer to the control panel’s Installation &

Setup Guide for details.

Function

Keys

Equivalent Key Pairs

A

[1] and [*]

B

[*] and [#]

C

[3] and [#]

D

NONE

•

Function keys must be held down for at

least 2 seconds to activate the programmed

function.

•

If functions other than panics are assigned

to

the

programmable

function

keys,

programmed panics must be initiated by

pressing the programmed key pair.

FUNCTION KEY LABELS

A set of adhesive-backed labels with some typical function

symbols (i.e., fire, police, personal emergency, etc.) is

provided.

These labels can be placed on or next to the keys

to identify each key's function for the end user (as

determined by the capability and programming of the

control panel; refer to the installation and setup guide for

the control panel).

6160V-001-V1

MOUNTING RELEASE SNAPS

(Remove case back by pushing up the 2 "snaps" along

the keypad's bottom edge and pulling the case apart.)

1

OFF

4

MAX

7

INSTANT

READY

2

AWAY

5

TEST

8

CODE

0

3

STAY

6

BYPASS

9

CHIME

#

SIDE

VIEW

D

C

B

A

WIRING AND INSTALLATION

Keypads can be surface mounted using drywall anchors or

to a single- or double-gang electrical box.

1.

Remove the case back

by pushing up the two "snaps"

along the keypad’s bottom edge and pulling the case

apart.

See diagram above.

2.

Route wiring from the control panel

through the

opening in the case back.

3.

Mount the case back

to a wall or electrical box.

4.

Wire directly from the keypad’s terminal block

to

the terminal block on the control board. (See Wiring

Table that follows.)

Wiring Table (All Keypads)

Keypad

Control Panel

Wire Color

G

Data In

Green

–

– Aux Pwr (GND)

Black

+

+ Aux. Pwr

Red

Y

Data Out

Yellow

5.

Re-attach the keypad

to the case back.

6.

Remove clear protective film from LEDs (6160V

only).

Honeywell 6150V Installation Guide

Honeywell 6150V Manual

Honeywell 6150V manual content summary: