Home » Honeywell Manuals » Thermostats » Honeywell CT3200 » Manual Viewer

Honeywell CT3200 Owner's Manual - Page 1

Honeywell CT3200 Manual

Get Honeywell CT3200 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

MagicStat® CT3200 Programmable Thermostat Installation and Programming Instructions Weekday/Weekend (5-day/2-day) Programmable Heat and/or Cool Low Voltage (20 to 30 Vac) Thermostat and Mounting Plate Model CT3200 Welcome to the world of comfort and energy savings with your new Honeywell MagicStat® Programmable Thermostat. Your new thermostat will automatically control the temperature in your home, keeping you comfortable while saving energy. If you have any questions about using this thermostat, visit our home expert Web site at www.honeywell.com/yourhome or call Honeywell Customer Relations at 1-800-468-1502. Table of Contents Installation 2 Programming 11 Operation 17 Change the clock for Daylight/ 17 Standard Time Set the Fan and System switches 17 Replace the batteries 18 Override the program settings 19 Frequently asked questions 21 Limited 1-Year Warranty 23 ®U.S. Registered Trademark Copyright © 2001 Honeywell • All Rights Reserved 69- 0653- 6

Section	Page
MagicStat® CT3200 Programmable Thermostat	1
Verify that you have the right thermostat	2
Step 1. Prepare for installation	3
a. Carefully unpack your new thermostat. Save your receipt and make sure you have the following p...	3
b. Gather the needed tools and supplies listed below.	3
c. Make sure that your heating and cooling systems are working properly. If there is a problem wi...	3
Step 2. Remove the old thermostat	4
Step 3. Install the mounting plate	5
Step 4. Set the thermostat for your type of heating system	6
Heating System Table	7
Note: Setting the screw “out one turn” means turning the screw 360˚ counter-clockwise, or one com...	7
Step 5. Wire the thermostat terminals	7
Step 6. Mount the thermostat	8
Step 7. Install the batteries	8
Special wiring instructions	9
A clock thermostat with C or C1 terminals	9
A clock thermostat has one or two extra wires attached to the C or C1 terminals that allow the cl...	9
a. Make sure that power to the heating/cooling system is turned off.	9
b. Locate the wires that are connected to the clock terminals marked C or C1.	9
c. As you disconnect the wires, do not allow these wires to touch.	9
d. Wrap the wires separately, using electrical tape to insulate the wires.	9
e. Place the wires where they will not interfere with the operation of the new thermostat. You wi...	9
f. Continue with the installation as instructed on page 4 at step 2e.	9
Six or more wires	9
If your old thermostat has six or more wires (excluding clock wires attached to the C or C1 termi...	9
Three thermostat wires	9
If you have three wires for heating only and can operate the fan using the fan ON switch, the 320...	9
Wires that are not connected to the old thermostat	9
If there are extra wires that do not connect to your old thermostat, do not label them. You will ...	9
Five wires connected to the old thermostat	10
Your new thermostat has a factory-installed metal jumper between the R and Rc terminals (Fig. 15)...	10
Old thermostat terminals that do not match new thermostat terminals	10
Use the table below to wire the new thermostat.	10
Step 1. Set the current time and day	12
Step 2. Learn about the programming features	12
Programming tips	13
Step 3. Program the heating schedule	14
a. Write in the times and temperatures that you want to program for your heating schedule.	14
Step 4. Program the cooling schedule	15
a. Write in the times and temperatures that you want to program for your cooling schedule.	15
b. Set the System switch to COOL.	16
c. Repeat steps 3c. through 3k. to program the weekday and weekend cooling schedule.	16
Step 5. Check out the system	16
Change the clock for Daylight/Standard time	17
a. Press once. The time is displayed.	17
b. Press and hold or until the correct time is displayed.	17
c. Press once. The current time and day and the current temperature are displayed.	17
Set the Fan and System switches	17
Replace the batteries	18
a. Make sure that the System switch is set in the OFF position.	18
b. Open the battery door.	18
c. Press on the left side of the batteries to remove them.	18
d. Install the new batteries. Make sure that the positive and negative terminals are oriented cor...	18
e. Close the battery door and set the System switch to HEAT or COOL.	18
Override the program settings	19
Frequently asked questions	21
Customer assistance	22
For all questions concerning this thermostat, please read and follow the instructions. If you nee...	22