Home » Honeywell Manuals » Thermostats » Honeywell CT3200 » Manual Viewer

Honeywell CT3200 Owner's Manual - Page 11

Faceplate illustration and descriptions - thermostat

Get Honeywell CT3200 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Programming Faceplate illustration and descriptions Fig. 16 7 8 6 AM PM SET SYSTEM ON 5 MO TU WE TH FR SA SU TEMPORARY WAKE LEAVE RETURN SLEEP 4 Time Temp 3 Set clock/Day Ahead Warmer Run Program 2 Set Schedule Back Cooler Hold Temp 1 Fan Auto On System Cool Off Heat Descriptions 1 Fan switch-Selects automatic fan operation or fan on (page 17) 9 2 Set Schedule-Puts the thermostat into programming 10 mode (page 14) 11 3 Set Clock/Day-Sets the clock and day (page 12) 4 Time Ahead and Back-Sets the time ahead and 12 back (page 12) 5 Program periods-Current program period or period 13 being programmed (page 13) 6 Day of the week-Current day or day being programmed 14 7 Time-Current time or program time M20141 8 Temperature-Room temperature or programmed temperature 9 SYSTEM ON-An arrow displays when the heating/ cooling system is running (page 16) 10 TEMPORARY-An arrow displays when a temporary override is made to the program (page 19) 11 Temp Warmer and Cooler-Sets the temperature warmer and cooler (page 14) 12 Run Program-Returns thermostat to normal operating mode 13 Hold Temp-Holds a selected temperature (page 19) 14 System switch-Selects Cool, Off, Heat (page 18) 69-0653-6 PROGRAMMING 11

Section	Page
MagicStat® CT3200 Programmable Thermostat	1
Verify that you have the right thermostat	2
Step 1. Prepare for installation	3
a. Carefully unpack your new thermostat. Save your receipt and make sure you have the following p...	3
b. Gather the needed tools and supplies listed below.	3
c. Make sure that your heating and cooling systems are working properly. If there is a problem wi...	3
Step 2. Remove the old thermostat	4
Step 3. Install the mounting plate	5
Step 4. Set the thermostat for your type of heating system	6
Heating System Table	7
Note: Setting the screw “out one turn” means turning the screw 360˚ counter-clockwise, or one com...	7
Step 5. Wire the thermostat terminals	7
Step 6. Mount the thermostat	8
Step 7. Install the batteries	8
Special wiring instructions	9
A clock thermostat with C or C1 terminals	9
A clock thermostat has one or two extra wires attached to the C or C1 terminals that allow the cl...	9
a. Make sure that power to the heating/cooling system is turned off.	9
b. Locate the wires that are connected to the clock terminals marked C or C1.	9
c. As you disconnect the wires, do not allow these wires to touch.	9
d. Wrap the wires separately, using electrical tape to insulate the wires.	9
e. Place the wires where they will not interfere with the operation of the new thermostat. You wi...	9
f. Continue with the installation as instructed on page 4 at step 2e.	9
Six or more wires	9
If your old thermostat has six or more wires (excluding clock wires attached to the C or C1 termi...	9
Three thermostat wires	9
If you have three wires for heating only and can operate the fan using the fan ON switch, the 320...	9
Wires that are not connected to the old thermostat	9
If there are extra wires that do not connect to your old thermostat, do not label them. You will ...	9
Five wires connected to the old thermostat	10
Your new thermostat has a factory-installed metal jumper between the R and Rc terminals (Fig. 15)...	10
Old thermostat terminals that do not match new thermostat terminals	10
Use the table below to wire the new thermostat.	10
Step 1. Set the current time and day	12
Step 2. Learn about the programming features	12
Programming tips	13
Step 3. Program the heating schedule	14
a. Write in the times and temperatures that you want to program for your heating schedule.	14
Step 4. Program the cooling schedule	15
a. Write in the times and temperatures that you want to program for your cooling schedule.	15
b. Set the System switch to COOL.	16
c. Repeat steps 3c. through 3k. to program the weekday and weekend cooling schedule.	16
Step 5. Check out the system	16
Change the clock for Daylight/Standard time	17
a. Press once. The time is displayed.	17
b. Press and hold or until the correct time is displayed.	17
c. Press once. The current time and day and the current temperature are displayed.	17
Set the Fan and System switches	17
Replace the batteries	18
a. Make sure that the System switch is set in the OFF position.	18
b. Open the battery door.	18
c. Press on the left side of the batteries to remove them.	18
d. Install the new batteries. Make sure that the positive and negative terminals are oriented cor...	18
e. Close the battery door and set the System switch to HEAT or COOL.	18
Override the program settings	19
Frequently asked questions	21
Customer assistance	22
For all questions concerning this thermostat, please read and follow the instructions. If you nee...	22

Match case Limit results 1 per page

69-0653-6

PROGRAMMING

Fan

Auto

System

Cool

Off

Heat

Set

Schedule

Set

clock/Day

Back

Ahead

Cooler

Warmer

Hold

Temp

Run

Program

SYSTEM ON

TEMPORARY

Temp

Time

WAKE

LEAVE

RETURN

SLEEP

SET

M20141

Programming

Faceplate illustration and descriptions

Descriptions

Fan switch

–

Selects automatic fan operation or fan on

(page 17)

Set Schedule

–

Puts the thermostat into programming

mode (page 14)

Set Clock/Day

–

Sets the clock and day (page 12)

Time Ahead and Back

–

Sets the time ahead and

back (page 12)

Program periods

–

Current program period or period

being programmed (page 13)

Day of the week

–

Current day or day being

programmed

Time

–

Current time or program time

Temperature

–

Room temperature or programmed

temperature

SYSTEM ON

–

An arrow displays when the heating/

cooling system is running (page 16)

TEMPORARY

–

An arrow displays when a temporary

override is made to the program (page 19)

Temp Warmer and Cooler

–

Sets the temperature

warmer and cooler (page 14)

Run Program

–

Returns thermostat to normal

operating mode

Hold Temp

–

Holds a selected temperature (page 19)

System switch

–

Selects Cool, Off, Heat (page 18)

Fig. 16