Home » Honeywell Manuals » Power Supplies » Honeywell HPFF12 » Manual Viewer

Honeywell HPFF12 Operation Manual - Page 47

Class A Input Connections

Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

HPFFconnex-Binput.wmf Connecting Multiple Units Applications Figure 5.7 Class B Input Connections w Figure 5.8 Class A Input Connections HPFFconnex6-Ainput.wmf HPFFconnex-split.psd Figure 5.9 Split Alarm Connections Figure 5.10 Selective Silencing Connections NOTES for Figures 5.5-5.10: 1. The FACP's NAC output must be regulated (not Full Wave Rectified [FWR]) if the HPFF is programmed for Sync Generator. 2. The number of possible units that can be interconnected depends on the current capability of the FACP output. Each HPFF8 input draws 12.26 mA at 24 VDC. 3. The total line impedance for interconnected units cannot be such that it creates a voltage drop > 2 VDC. Zline total =2V/(1 Unit + 1 ELR) Example: Zline total = 2V/(12.26 mA + (24-2)/4.7K) =118.1 ohms HPFF12 NAC Expander - P/N 53576:B 11/24/2010 47

Section	Page
Table of Contents	5
Section 1: System Overview	9
1.1 General	9
1.2 Features	10
1.3 Start-up Procedure	11
1.4 Jumpers	12
1.4.1 Charger Disable Jumper (J1)	12
1.4.2 Ground Fault Disable Jumper (J2)	12
1.5 LED Indicators	13
1.6 Specifications	13
Section 2: Installation	17
2.1 Backbox Mounting	17
2.2 Chassis-Mounting in FACP Cabinets	21
2.3 NAC Circuit Wiring	26
2.3.1 Four NACs Configured for Class B (Style Y)	26
2.3.2 Two NACs Configured for Class A (Style Z)	27
2.3.3 Mixing Class B and Class A NACs	28
2.3.4 HPP31076 Optional Class A (Style Z) Adaptor	29
2.4 Mounting Addressable Modules	30
2.4.1 Mounting Modules from Honeywell Fire Systems	30
2.4.2 Mounting Six-Circuit Modules from Honeywell Fire Systems	31
2.5 Power-Limited Wiring Requirements	31
2.5.1 Power-Limited Wiring, Standard Chassis	32
2.5.2 Power-Limited Wiring, FACP Cabinet	33
Section 3: Programming Options	35
3.1 DIP Switch Settings	35
3.2 Programmable Features	36
3.2.1 Input/Output Functions	36
3.2.2 Synchronization Type	37
3.2.3 Trouble Reporting Delay with an AC Failure	37
3.2.4 Split Alarm and Silencing	38
Section 4: Trouble Supervision	39
4.1 Supervised Functions and Field Wiring	39
4.2 Trouble Reporting	39
4.2.1 TB2: AC FAIL Contacts	40
4.2.2 TB2: TROUBLE Contacts	40
4.2.3 TB3: Initiating Device Inputs SIGNAL 1 and SIGNAL 2	40
4.2.4 Trouble Memory	41
4.2.5 Ground Fault Detection	41
4.2.6 NAC Overload Protection and Indication	41
Section 5: Applications	42
5.1 Controlling Four NAC Circuits from a Single Source	42
5.2 Controlling and Silencing Four NACs	43
5.3 Split Alarm and Selective Silence	44
5.3.1 Selective Silence	44
5.3.2 Split Alarm Mode	45
5.4 Connecting Multiple Units	46
Section 6: Power Supply Requirements	48
6.1 Overview	48
6.2 Calculating the AC Branch Circuit Current	48
6.3 Calculating the System Current Draw	49
6.3.1 Overview	49
6.3.2 How to Calculate System Current Draw	50
6.4 Calculating the Battery Size	51
6.4.1 NFPA Battery Requirements	51
6.4.2 Selecting and Locating Batteries	51
6.5 NAC Circuit Loop Wiring Requirements	52
Appendix A: Device Compatibility	53
A.1 Optional Modules	53
A.2 Notification Appliances	53
A.2.1 System Sensor — 24 VDC	53
A.2.2 Gentex — 24 VDC	54
A.2.3 Cooper-Wheelock	55
A.2.4 Amseco	57
A.2.5 Faraday	57