Honeywell MK1650-62B14 User Guide

Honeywell MK1650-62B14 - Metrologic IS1650 - Wired Stationary Barcode Scanner Manual

Get Honeywell MK1650-62B14 - Metrologic IS1650 - Wired Stationary Barcode Scanner PDF manuals and user guides View all Honeywell MK1650-62B14 manuals
Add to My Manuals
Save this manual to your list of manuals

Honeywell MK1650-62B14 manual content summary:

  • Honeywell MK1650-62B14 | User Guide - Page 1
    METROLOGIC INSTRUMENTS, INC. IS1650 FocusE™ Area Imaging Bar Code Scanner Installation and User's Guide
  • Honeywell MK1650-62B14 | User Guide - Page 2
    consent, except by reviewer, who may quote brief passages in a review, or provided for in the Copyright Act of 1976. Trademarks Metrologic is a registered trademark of Metrologic Instruments, Inc. Products identified in this document are hereby acknowledged as trademarks, registered or otherwise, of
  • Honeywell MK1650-62B14 | User Guide - Page 3
    (Interface Specific 12 RS232 IS1650-14 12 Keyboard Wedge IS1650-47 13 Stand Alone Keyboard IS1650-47 14 IBM 46xx IS1650-106 15 Low Speed USB IS1650-38 (Integrated 16 Full Speed USB IS1650-106 (Integrated 16 Flex Stand Installation 17 SCANNER CONFIGURATION Configuration Modes 19 Bar
  • Honeywell MK1650-62B14 | User Guide - Page 4
    Width 25 IR Activation Range 26 MAINTENANCE Daily Maintenance 27 TROUBLESHOOTING GUIDE Troubleshooting Symptom / Solution Chart 28 DEFAULT SETTINGS Communication Parameters 32 SCANNER AND CABLE TERMINATIONS Scanner Pinout Connections 36 Cable Connector Configurations 38 PATENTS 43 LIMITED
  • Honeywell MK1650-62B14 | User Guide - Page 5
    INTRODUCTION PRODUCT OVERVIEW The IS1650 is a high performance area imaging bar code scanner that utilizes a high-resolution CMOS imaging sensor for unrivaled image quality. The IS1650 is the choice of 2D imaging scanners that delivers superior performance for presentation and fixed-mount
  • Honeywell MK1650-62B14 | User Guide - Page 6
    scanner includes the scanner number and factory default communications protocol. SCANNER VERSION IDENTIFIER COMMUNICATION PROTOCOL(S) 14 RS232 (TX, RX, RTS, CTS, DTR) IS1650 - 38 Low Speed USB USB, and RS232 Transmit/Receive The IS1650 information on the IS1650's default settings refer
  • Honeywell MK1650-62B14 | User Guide - Page 7
    Description IS1650 Area Imaging Bar Code Scanner 00-02544 MetroSelect® Single-Line Configuration Guide* 00-02281 Area Imaging Supplemental Configuration Guide* 00-02287 IS1650 Series Area Imaging Bar Code Scanner Installation and User's Guide* * Also available for download on the Metrologic
  • Honeywell MK1650-62B14 | User Guide - Page 8
    # OPTIONAL ACCESSORIES Description IS1650 Scanner Interface Specific Cables 59- USB Power/Communication Cable, 2.9 m (9.5 ft.) straight, black MVC-3M106S- Metrologic Voltage Converter (MVC) Cable* IB9 ±12VDC to +5.2VDC, 2.1m (7.0 ft.) straight, black * Contact a Metrologic customer service
  • Honeywell MK1650-62B14 | User Guide - Page 9
    Cover Qty. 1 d. Scanner Cradle Qty. 1 e. 1/4" - 20 x 1/2" Flat Head Phillips Qty. 2 f. #8 Round Head Wood Screw Qty. 2 Other items may be ordered for the specific protocol being used. To order additional items, contact the dealer, distributor or call Metrologic's Customer Service Department at
  • Honeywell MK1650-62B14 | User Guide - Page 10
    of an Osram LED: Depth of Scan Field: IS1650 DESIGN SPECIFICATIONS LED 645 nm 1 ms to 8 ms Composites, Postals, Aztec, *OCR (A, B, MICR) (Image Transfer) - BMP, TIFF, or JPEG output * Optional System Interfaces: IBM 468X/469X, Stand Alone Keyboard, USB (Low/Full Speed) Print Contrast: 20% Minimum
  • Honeywell MK1650-62B14 | User Guide - Page 11
    INTRODUCTION DESIGN SPECIFICATIONS (CONT.) ELECTRICAL IS1650 DESIGN SPECIFICATIONS Input Voltage: 5.0VDC ± 0.25V Peak = 2 W (Typical) Power: Operating = 1.65 W (Typical) Idle / Standby = 800 mW (Typical) Peak = 400 mA (Typical) Current: Operation = 330 mA (
  • Honeywell MK1650-62B14 | User Guide - Page 12
    BASE MODEL CHARACTERISTICS IS1650 SCANNER Components Figure 1. Scanner Components Item Description 1 Red Window LED Aperture Indicators (on page 22) 7 Cable Connection 10-pin RJ45, Female Socket, See Scanner Pinout Connections (on page 36) 8 Cable Release See The PowerLink Cable (on page
  • Honeywell MK1650-62B14 | User Guide - Page 13
    BASE MODEL CHARACTERISTICS IS1650 SCANNER Dimensions Figure 2. Scanner Dimensions Figure 3. M3 Mounting Hole Dimensions Caution: The depth of each mounting hole is 12 mm (0.5"). For fixed mount, the mounting screws should not be
  • Honeywell MK1650-62B14 | User Guide - Page 14
    BASE MODEL CHARACTERISTICS IS1650 SCANNER Caution and Serial Number Labels Each scanner has a label located on the bottom of Caution: To maintain compliance with applicable standards, all circuits connected to the scanner must meet the requirements for SELV (Safety Extra Low Voltage) according to
  • Honeywell MK1650-62B14 | User Guide - Page 15
    the PowerLink cable is not fully 'latched', the unit can power intermittently. Figure 5. Figure 6. Disconnecting Before removing the cable from the scanner, Metrologic recommends that the power on the host system is off and the power supply has been disconnected from the PowerLink cable. Figure
  • Honeywell MK1650-62B14 | User Guide - Page 16
    -pin socket on the IS1650. There will be an 8. 6. The IS1650 will start to scanner is ready for use. 7. Turn on the host device. Plugging the scanner Guide (MLPN 00-02544) or MetroSet2's help files for instructions on changing the scanner's configuration. In addition, please check that the scanner
  • Honeywell MK1650-62B14 | User Guide - Page 17
    pin socket on the IS1650. There will be the scanner for The IS1650 will start scanner is ready for use. 8. Turn on the host device. Plugging the scanner Guide (MLPN 00-02544) or MetroSet2's help files for instructions on changing the scanner's configuration. In addition, please check that the scanner
  • Honeywell MK1650-62B14 | User Guide - Page 18
    10-pin socket on the IS1650. There will be an . 6. The IS1650 will start to scanner is ready for use. 7. Turn on the host device. Plugging the scanner Guide (MLPN 00-02544) or MetroSet2's help files for instructions on changing the scanner's configuration. In addition, please check that the scanner
  • Honeywell MK1650-62B14 | User Guide - Page 19
    pin socket on the IS1650. There will be device. 5. The IS1650 will start to initialize. All scanner is ready for use. Figure 11. Plugging the scanner Guide (MLPN 00-02544) or MetroSet2's help files for instructions on changing the scanner's configuration. In addition, please check that the scanner
  • Honeywell MK1650-62B14 | User Guide - Page 20
    Emulation Mode enabled. For information on configuring the IS1650-38 for USB Serial Emulation Mode, please refer to the USB section of the MetroSelect Single-Line Configuration Guide (MLPN 00-02544). Plugging the scanner into a port on the host device does not guarantee that scanned information
  • Honeywell MK1650-62B14 | User Guide - Page 21
    INSTALLATION FLEX STAND INSTALLATION (OPTIONAL) Metrologic provides two #8 wood screws for securing the stand base to the counter top. The following figure provides the pilot hole dimensions for securing the stand base. Figure 13. Stand Base Hole Pattern (Not to Scale) 17
  • Honeywell MK1650-62B14 | User Guide - Page 22
    INSTALLATION FLEX STAND INSTALLATION (OPTIONAL) Figure 14. Assembling the Stand 18
  • Honeywell MK1650-62B14 | User Guide - Page 23
    CONFIGURATION MODES The IS1650 Series scanner has three modes of configuration. • Bar Codes The IS1650 can be configured by scanning the bar codes included in the Metrologic Single-Line Configuration Guide (MLPN 00-02544) or the Supplemental Configuration Guide (MLPN 00-02281). These manuals can be
  • Honeywell MK1650-62B14 | User Guide - Page 24
    CONFIGURATION The IS1650 FocusE is part of Metrologic's line of scanners with flash upgradeable firmware. The upgrade process requires a new firmware file supplied to the customer by a customer service representative and Metrologic's MetroSet2 software . A personal computer running Windows 95
  • Honeywell MK1650-62B14 | User Guide - Page 25
    Mode, Out-of-Stand * The IS1650 can switch into different modes of operation using the MetroSet2 Software or Area Imaging Supplemental Guide (00-02281). 1. The IR detects an object in the IR activation range and automatically turns on linear illumination. 2. Aim the scanner's line of light over the
  • Honeywell MK1650-62B14 | User Guide - Page 26
    When the IS1650 is in operation, it provides audible feedback. These sounds indicate the status of the scanner. Eight settings are available for the tone of the beep (normal, 6 alternate tones and no tone). To change the tone, refer to the MetroSelect Single-Line Configuration Guide, MLPN 00
  • Honeywell MK1650-62B14 | User Guide - Page 27
    in the stand. Figure 15. Steady Blue The blue LED illuminates when the scanner is active and linear illumination is on or when the scanner is attempting to decode a barcode. Steady Blue and Single White Flash When the scanner successfully reads a bar code, it will beep once and the white LED will
  • Honeywell MK1650-62B14 | User Guide - Page 28
    OPERATION FAILURE MODES Long Razzberry Tone - During Power Up Failed to initialize or configure the scanner. If the scanner does not respond after reprogramming, return the scanner for repair. Short Razzberry Tone - During Scanning An Invalid bar code has been scanned when in configuration. 24
  • Honeywell MK1650-62B14 | User Guide - Page 29
    SCANNER OPERATION DEPTH OF FIELD BY MINIMUM BAR CODE ELEMENT WIDTH MINIMUM BAR CODE ELEMENT WIDTH 1D PDF A B C D E F G mm .132 .191 .254 .330 .533 .254 .381 mils 5.2 7.5 10.4 13 21 10 Figure 16. Depth of Field by Minimum Bar Code Element Width 15.9
  • Honeywell MK1650-62B14 | User Guide - Page 30
    SCANNER OPERATION IR ACTIVATION RANGE The IS1650 has a built in object detection sensor that instantly turns on the scanner when an object is presented within the scanner's IR activation Area. Figure 17. IR Activation Area Specifications are subject to change without notice. 26
  • Honeywell MK1650-62B14 | User Guide - Page 31
    MAINTENANCE DAILY MAINTENANCE Smudges and dirt on the unit's window can interfere with the unit's performance. If the window requires cleaning, use only a mild glass cleaner containing no ammonia. When cleaning the window, spray the cleaner onto a lint free, nonabrasive cleaning cloth then gently
  • Honeywell MK1650-62B14 | User Guide - Page 32
    TROUBLESHOOTING GUIDE The following guide is for reference purposes only. Contact a Metrologic representative at 1-800-ID-Metro or 1-800-436-3876 to preserve the limited warranty terms. All Interfaces IS1650 Series Troubleshooting configure the scanner. Contact a Metrologic Service Representative if
  • Honeywell MK1650-62B14 | User Guide - Page 33
    TROUBLESHOOTING GUIDE Code 39, interleaved 2 of 5, Code 93, Code 128, Codabar and PDF are enabled by default. Verify that the type of bar code being read has USB Interfaces. The unit scans a bar code, but locks up after the first scan and the white LED stays on. The scanner is configured to support
  • Honeywell MK1650-62B14 | User Guide - Page 34
    TROUBLESHOOTING GUIDE Symptoms Possible Causes Solution The unit beeps at some bar codes and NOT for others of the same bar code symbology. The bar code may have been printed incorrectly. The scanner is not configured correctly for this type of bar code. The minimum symbol length setting does
  • Honeywell MK1650-62B14 | User Guide - Page 35
    TROUBLESHOOTING GUIDE Symptoms The unit is transmitting each character twice. Possible works except for a couple of characters. These characters may not be supported by that country's key look up table. Try operating the scanner in Alt mode. The following item is only relevant for an RS232
  • Honeywell MK1650-62B14 | User Guide - Page 36
    scanner has an asterisk (*) in the charts on the following pages. If an asterisk is not in the default column then the default setting is OFF or DISABLED. Not every interface supports every parameter. If the interface supports Code 39 PDF * Data Matrix QR Code RS232 KBW IBM 46XX & KEYBOARD
  • Honeywell MK1650-62B14 | User Guide - Page 37
    39 MSI-Plessy 10/10 Check Digit MSI-Plessy Mod 10 Check Digit Paraf Support ITF ITF Symbol Lengths Symbol Length Lock Beeper tone Beep/transmit sequence Communication -13 DEFAULT RS232 KBW IBM 46XX & KEYBOARD USB * Variable None Normal Before transmit None * 1 msecs 10 msecs in KBW 8 * 33
  • Honeywell MK1650-62B14 | User Guide - Page 38
    Enabled UPC Prefix UPC Suffix Carriage Return Line Feed-Disabled by default in KBW Tab Prefix Tab Suffix "DE" Disable Command Enable Command DTR Handshaking support RTS/CTS Handshaking Character RTS/CTS Message RTS/CTS * * * No 9600 * 1 * * * RS232 KBW IBM 46XX & KEYBOARD
  • Honeywell MK1650-62B14 | User Guide - Page 39
    128 † Configurable Code Lengths DEFAULT RS232 KBW IBM 46XX & KEYBOARD USB * * 7 avail † Code Selects with configurable Code Length Suffix characters Prefixes for Individual Code types Editing Function/Control Key Support Omnidirectional Scanning Linear Only Scanning Linear 1D / Omni 2D 3
  • Honeywell MK1650-62B14 | User Guide - Page 40
    interfaces terminate to a 10-pin, RJ45 Female Socket. The serial # label indicates the interface enabled when the scanner is shipped from the factory. IS1650-14 RS232 Pin Function 1 Ground 2 RS232 Transmit Output 3 RS232 Receive Input 4 RTS Output 5 CTS Input 6 DTR Input 7 Reserved 8 Reserved
  • Honeywell MK1650-62B14 | User Guide - Page 41
    AND CABLE TERMINATIONS SCANNER PINOUT CONNECTIONS IS1650-38 Low Speed USB Pin Function 1 Ground 2 RS232 Transmit Output 3 RS232 Receive Input 4 RTS Output 5 CTS Input 6 USB D+ 7 V USB 8 USB D9 +5VDC 10 Shield Ground IS1650-106 IBM 46xx / Full Speed USB Pin Function 1 Ground 2 RS232 Transmit
  • Honeywell MK1650-62B14 | User Guide - Page 42
    SCANNER AND CABLE TERMINATIONS CABLE CONNECTOR CONFIGURATIONS (HOST END) "Standard" PowerLink Cable 59- PC Power to KB 5 PC Clock 6 NC 21 4 3 65 6-Pin Male Mini-DIN Connector USB Power/Communication Cable 59-59313-N-3, Straight Pin Function 1 PC +5V/V_USB 2 D- 3 D+ 4 Ground Shield
  • Honeywell MK1650-62B14 | User Guide - Page 43
    SCANNER AND CABLE TERMINATIONS CABLE CONNECTOR CONFIGURATIONS (HOST END) Keyboard Wedge Clock 6 No Connect 2 4 5 1 3 5-Pin DIN, Female 2 1 4 3 65 6-Pin DIN, Male Metrologic will supply an adapter cable with a 5-pin DIN male connector on one end and a 6-pin mini DIN female connector
  • Honeywell MK1650-62B14 | User Guide - Page 44
    to service the LED scanner. Never attempt to look at the LED beam, even if the scanner appears to be nonfunctional. Never open the scanner in presente Manuale può provocare delle rischiose esposizioni radiattive. Il cliente non deve assolutamente tentare di riparare egli stesso lo scanner LED
  • Honeywell MK1650-62B14 | User Guide - Page 45
    scanner cable is greater in length than 3 meters (9.8 feet) when fully extended: Les instructions ci-dessous s'appliquent aux cables de scanner accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
  • Honeywell MK1650-62B14 | User Guide - Page 46
    to operate the equipment. Class B Devices The following is applicable when the scanner cable is less than 3 meters (9.8 feet) in length when fully extended: Les instructions ci-dessous s'appliquent aux cables de scanner ne dépassant pas 3 métres (9.8 pieds) de long en extension maximale: Folgendes
  • Honeywell MK1650-62B14 | User Guide - Page 47
    use of the specific equipment, circuits, and devices represented by or contained in the METROLOGIC products that are physically transferred to the user, and only to the extent of METROLOGIC'S license rights and subject to any conditions, covenants and restrictions therein. Other worldwide patents
  • Honeywell MK1650-62B14 | User Guide - Page 48
    LIMITED WARRANTY The IS1650 series scanners are manufactured by Metrologic at its Blackwood, New Jersey, U.S.A. facility. The IS1650 series scanners have a five (5) year limited warranty from the date of manufacture. Metrologic warrants and represents that all IS1650 series scanners are free of all
  • Honeywell MK1650-62B14 | User Guide - Page 49
    20, 28- 31, 38-39 RS232 12, 38-39 Stand Alone Keyboard . 14, 38-39 USB 16, 38-39 Caution 12-16, 40 CE 10, 12-16 Class 41, 42 Communication Parameters 2, 3, 19, 20, 28-31 Connector Pinouts 36-37 Converter 16 Current 7 Customer Service 3, 4, 5, 44 D DC 3, 7, 36-37, 38-39 Decode 6 Default
  • Honeywell MK1650-62B14 | User Guide - Page 50
    21 Mode of Operation 21 Mounting See Stand N Notices 42 P Patent 43 PDF 25 Pinouts 36-37, 38-39 Power 7, 12-16, 20 Power Supply Tone 23-24 Alternate 22 Transformer 3, 7, 12-16 Trigger 8, 21 Troubleshooting 28-31 U UL 10, 12-16 Upgrade 20 USB Full Speed .. 1, 2, 4, 5, 16, 32-35, 37,
  • Honeywell MK1650-62B14 | User Guide - Page 51
    47
  • Honeywell MK1650-62B14 | User Guide - Page 52
    NOTES
  • Honeywell MK1650-62B14 | User Guide - Page 53
    NOTES
  • Honeywell MK1650-62B14 | User Guide - Page 54
  • Honeywell MK1650-62B14 | User Guide - Page 55
  • Honeywell MK1650-62B14 | User Guide - Page 56
    January 2008 Printed in the USA 00 - 02287C
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
METROLOGIC INSTRUMENTS, INC.
IS1650 Focus
E
™
Area Imaging Bar Code Scanner
Installation and User’s Guide