Honeywell TI071 User Guide

TI071

400-071-000-A

2007-12-13

1/2

The TI071 programmable wall switch has been designed to control lights and motors:

Cut power at the circuit breaker to avoid electric shock.

Remove the existing switch.

Install the new switch.

Apply power at the circuit breaker.

The TI071 will turn the lights on at sunset and turn them off at 11:00 pm by default. If these settings are

appropriate for you, you only need to set the time and date (see shaded zone in programming flowchart).

The switch is now ready to go.

5.1

Mode Menu

You can use the Mode menu to select one of the three modes of operation (see sections 5.1.1 to 5.1.3).

5.1.1

Manual Mode

In Manual mode, the TI071 operates like a regular switch. To turn the lights on or off, briefly

press the main button. The

icon appears when the switch is in Manual mode.

5.1.2

Automatic Mode

In Automatic mode, the TI071 turns the lights on or off according to the set programs (see

Section 5.4). The

icon as well as the current program number are displayed.

5.1.3

Random Mode

In Random mode, the TI071 has no specific times to turn the lights on or off. This mode is

designed to give the impression the house is occupied during your absence. It is similar to

the Automatic mode except there is no fixed program. The programs are automatically set

to different times by the TI071 every day. The

icon appears when the switch is in

Random mode.

The first “On” program occurs at sunset. Each “On” program lasts between 1 hour and 1

hour and 30 minutes; each “Off” program lasts between 15 and 30 minutes. The last “Off”

program occurs between 10:30 pm and midnight.

5.1.4

Temporary Override

When the TI071 is in Automatic or Random mode, you can press the main button at any time to override the

default state for the current program. The light will turn off if they are on and vice versa. The icon (On or Off)

of the new state flashes to indicate that the state is temporary. The new state is maintained until you press

the main button again or till the next “On” or “Off” program.

5.2

Time Menu

The time display flashes on the screen when the time has not yet been set or after a 4-hour power outage.

Use the Time menu to select the time format (12-hour or 24-hour) and to set the clock and date.

NOTE

: The date is used to determine the sunset and sunrise times.

5.3

Configuration Menu

Use the Configuration menu to set the following parameters (see sections 5.3.1 to 5.3.4).

5.3.1

Backlight mode (

SCRN

)

The screen is lit at high intensity for 8 seconds when you press any button. The rest of the time, depending

on the backlight mode selected, the screen behaves as follows:

Scrn Off

: The screen is not lit.

Scrn On HI

: The screen is lit at high intensity.

Scrn On LO

: The screen is lit at low intensity (default mode).

5.3.2

Automatic Daylight Savings Time Changeover (

DLS

)

When automatic daylight savings time changeover is on (DLS On), the TI071 changes to daylight savings

time (summer time) at 2:00 on the second Sunday of March and changes back to normal time (winter time)

at 2:00 on the first Sunday of November. This function is enabled (DLS On) by default.

5.3.3

Longitude and Latitude Coordinates (

LONG

and

LAT

)

The coordinates are used to turn the lights on at sunset and off at sunrise. The longitude is set to -75 and the

latitude to +45 by default. These settings provide approximate sunset and sunrise times for most North

American cities. To obtain your city’s coordinates (or those of a nearby city), see the coordinates table. You

can also obtain this information at

www.aubetech.com/timer

or with a Global Positioning System (GPS)

device. The accuracy of the sunset and sunrise times depends on the accuracy of the coordinates you enter

for your city.

NOTE

: Enter a negative value for a south latitude or a west longitude.

Applications

Load types

Maximum load

Examples

Lights and resistive

loads (except tungsten)

1800 W

(15 A @ 120 V)

•

fluorescent lights

•

compact fluorescent lights (CFL)

•

electronic ballasts

•

sodium lamps

•

block heaters

Tungsten lights

1440 W

(12 A @ 120 V)

•

incandescent lights

•

halogen lights

Motors

3/4 hp

•

pool filter pumps

•

fans

Installation

NOTE:

This switch cannot be used if there is no neutral wire (indicated

by white wires joint together) inside the electrical box.

Quick Start-up

3.

Set the time and date before using the timer for the first time.

Operation

4.

120

VAC

black

white

black

white

black (LINE)

white (NEUTRAL)

blue (LOAD)

The

icon indicates the current

program has been activated at sunset.

The

icon indicates the current

program has been activated at sunrise.

The LED illuminates when the load state

is on.

Briefly press this button to turn the

lights on or off. See “Temporary

Override” in Section 5.1.4.

Indicates the mode of

operation (see Section 5.1)

Indicates the current program

You can change the mode of operation

by pressing this button for 1 second.

Indicates the load on/off state

Indicates the time and day

Programming

Refer to the programming flowchart.

TI071

User guide

7-day Solar Programmable Wall Switch

Honeywell TI071 User Guide

Honeywell TI071 - Aube by - Solar Programmable Timer Switch Manual

Honeywell TI071 manual content summary: