Honeywell TL8230A1008 User Guide

TL8230A

User Guide

Programmable Thermostat

TL8230A

69-1803

3/5/05

1/2

Honeywell’s TL8230A programmable thermostat can be connected to an

electric heater to control the room temperature.

*

Set the switch to Off to cut power to the heater. This will not affect the time and tem-

perature settings.

**

The thermostat displays the heater duty cycle required to maintain the desired tem-

perature. For example,

appears when the heater is activated 40 percent of the

time.

•

To remove the control module from the power

base, loosen the captive screw underneath the

thermostat and pull the two components apart

as shown.

•

To install the control module onto the power

base, reverse the above procedure.

NOTE:

Always keep the thermostat's vents clean and

unobstructed.

Some thermostat configurations can be

modified via the switches on the back of the

control module.

Default (factory) settings are inside the gray cells.

Upon power-up, the thermostat is in manual mode (

) and displays the

actual temperature.

Press the Hour and Min buttons to set the time.

Press the Day button to set the day.

LO

:

The measured temperature is below 32°F (0°C).

Heating is activated.

HI

:

The measured temperature is above 122°F (50°C).

When the backlight button is pressed, the display illuminates for 5 seconds.

When either of the

buttons is pressed, the display illuminates for 10 sec-

onds.

Setpoint

The thermostat generally displays the actual temperature. To view the

setpoint, press one of the

buttons once or press the backlight button. The

setpoint will appear for the next 5 seconds.

To change the setpoint, press one of the

buttons until the desired temper-

ature is displayed. To scroll faster, hold the button.

Preset buttons

The thermostat has 3 temperature preset buttons:

Comfort preset button

Economy preset button

Vacation preset button

To use a preset temperature, press the appropriate button. The corresponding

icon

,

or

will be displayed.

The following table shows the intended use and the default setting of each of

the preset buttons.

To store a preset temperature:

Set the desired temperature using the

buttons.

Press and hold the appropriate preset button until the corresponding

icon is displayed.

Press Mode/Ret to exit.

Description

1.

Display

% of duty cycle

1 to 24%

25 to 49%

50 to 74%

75 to 99%

100%

Assembly/Disassembly

2.

Configuration

3.

#

Functionality

UP

DN

SW1

Temperature format

a

a.

If you change the temperature display format, the preset buttons (

,

and

)

will return to their default settings.

°F

°C

SW2

Early Start

b

b.

Early Start functions in Automatic mode only. When this function is enabled, the

thermostat calculates the optimal time to start heating in order to obtain the desired

temperature by the set time. The thermostat re-assesses the start time daily based

on the previous day’s performance.

Disable

Enable

SW3

Time format

12-hour

24-hour

On/Off switch *

Day and time

settings

Temperature

adjustment

buttons

Program button

Mode selection /

program exit

Temperature display

Mode display

Period display

Temperature

preset buttons

Time and day display

Heating power **

Backlight button

Program

clear button

Preset temperature

icon

Appears when

the setpoint is

displayed

Power-up

4.

Error Messages

5.

Backlight

6.

Temperature Setting

7.

Icon

Intended use

Default setting

New

Comfort

(when at home)

70°F (21°C)

Economy

(when asleep or away from home)

62°F (16.5°C)

Vacation

(during prolonged absence)

50°F (10°C)

Honeywell TL8230A1008 User Guide

Honeywell TL8230A1008 - LineVoltPRO Programmable Thermostat Manual

Honeywell TL8230A1008 manual content summary: