Hoover H3000 Manual - Page 12
If you have a, problem - floor mate parts
UPC - 895916001179
View all Hoover H3000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
5. If you have a problem If a minor problem occurs, it usually can be solved quite easily when the cause is found by using the check list below. Problem: Machine won't run Possible cause Possible solution • Not firmly plugged in • Plug unit in firmly. • No voltage in wall plug • Check fuse or breaker. • Blown fuse/tripped breaker • Replace fuse/reset breaker. Problem: Low or no suction Possible cause Possible solution • Automatic shut-off activated • Turn cleaner OFF and then ON again or • Empty recovery tank (see "Automatic shut-off" section) • Filter or filter lid missing or not positioned correctly • Ensure that filter and filter lid are properly positioned in the recovery tank lid (Fig. 2-22) • Recovery tank and/or solution tank not positioned properly • Ensure that both tanks are locked in place. • Filter is dirty • Clean filter • Nozzle not properly positioned • Ensure nozzle is replaced properly and locked (Figs. 4-8 & 4-9). Problem: Water puddling behind cleaner Possible cause Possible solution • Excess cleaning concentrate foaming in tanks • Use Machine Formula LYSOL® Floor Cleaning Concentrate or Machine Formula OLD ENGLISH® Wood Floor Cleaning Concentrate, it is a low-foam formulation. If using cleaning concentrate other than LYSOL® brand or OLD ENGLISH® brand, remix cleaning solution using less concentrate. • Solution tank not properly installed • Ensure that tank is installed properly (Fig. 2-15).r • Recovery tank is full • Empty tankProblem: Cleaner does Problem: Cleaner does not pick up dirty solution Possible cause Possible solution • Cleaner not set for wet operation • Press wet/dry pedal to "WET" position. • Recovery tank not properly installed • Ensure that recovery tank is installed properly (Fig. 2-20). • Recovery tank full/automatic shut- off engaged. • Remove and empty recovery tank. • Filter or filter lid missing or not properly positioned. • Ensure recovery tank filter and filter lid are properly installed (Fig. 2-22). Problem: Cleaner pushes a line of dry debris in front of it Possible cause Possible solution • Cleaner not set for dry operation • Press wet/dry pedal to "DRY PICKUP" position. • Debris is too large to clear squeegee • Tip nozzle off floor by pushing down on handle. Problem: Clean solution won't dispense Possible cause Possible solution • Solution tank not firmly in place • Make sure tank is securely locked in position. • Solution tank empty • Refill solution tank. Problem: Brushes won't rotate Possible cause Possible solution • Cleaner set for "WET/DRY PICK- UP" • Move wet control switch down to "WET SCRUB" position (Fig. 2-7). • Circuit breaker inside cleaner is tripped • To reset the breaker: (1) Push the ON/OFF switch completely down. You will feel some resistance when the switch moves downward. The switch will also move slightly upward on its own. (2) Wait one minute. (3) Repeat step 1. (4) Turn the cleaner ON and continue cleaning. If the brushes continue to stall and the breaker trips again, clean the brushes to remove debris. (Figs. 4-1 through 4-4) Service To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: • checking the Yellow Pages under "Vacuum Cleaners Household" OR - • checking the list of Factory Service Centers provided with this cleaner OR - • checking the Service section of The Hoover Company on-line at www.hoover.com OR - • calling 1-800-944-9200 for an auto mated referral of authorized service outlet locations (U.S. only). Do not send your cleaner to The Hoover Company in North Canton for service, this will only result in delay. If further assistance is needed, contact The Hoover Company Consumer Response Center, North Canton, Ohio 44720 Phone: 1-330-499-9499. In Canada, contact Hoover Canada, Burlington, Ontario L7R 4A8, Phone: 1-800-263-6376. Always identify your cleaner by the complete model number when requesting information or ordering parts. (The model number appears at the bottom of the back of the cleaner body.) For questions or comments concerning Machine Formula LYSOL® or OLD ENGLISH® Floor Cleaning Concentrate, call 1-800-228-4722. LYSOL® and OLD ENGLISH® are registered trademarks of Reckitt Benckiser Inc. 12