Hotpoint HDA3540NSA Installation Instructions
Hotpoint HDA3540NSA - Metallic 24 Inch Full Console Dishwasher Manual
 |
View all Hotpoint HDA3540NSA manuals
Add to My Manuals
Save this manual to your list of manuals |
Hotpoint HDA3540NSA manual content summary:
- Hotpoint HDA3540NSA | Installation Instructions - Page 1
Consumer & Industrial Appliances Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com BEFORE YOU BEGIN STOP Read these instructions completely and carefully. IMPORTANT - Observe all governing codes and ordinances - Hotpoint HDA3540NSA | Installation Instructions - Page 2
PARTS SUPPLIED IN INSTALLATION PACKAGE: ■ Two 8-18 x 5/8" Phillips head wood screws ■ Junction box cover and #10 hex head screw ■ Drain hose (78" long) and hose clamp ■ Cord protector (Power Cord Models Only) ■ Conversion leads (Power Cord Models Only) ■ Literature, product samples, and/or coupons - Hotpoint HDA3540NSA | Installation Instructions - Page 3
from sink for proper drainage. • The dishwasher must be fully enclosed on the top, sides, and back. • The dishwasher must not support any part of the enclosure. • The rough cabinet nished floor of the kitchen. This will facilitate removal of the dishwasher at a later date for service, if needed. 3 - Hotpoint HDA3540NSA | Installation Instructions - Page 4
Install waste tee or disposer and the air gap according to the manufacturer's instructions. CAUTION An air gap MUST BE USED if the drain hose is minimum, high drain loop will result in improper draining of the dishwasher, which may cause damage. 307Dia51 Cabinet Preparation Drill a 1-1/2" diameter - Hotpoint HDA3540NSA | Installation Instructions - Page 5
on the appliance. Grounding Instructions-Power Cord Models This appliance must be grounded with a qualified electrician or service representative if you are in Models Only) Hole Diameter 1-1/2" Maximum Electrical Connection to Dishwasher Electrical connection is on the right front of dishwasher - Hotpoint HDA3540NSA | Installation Instructions - Page 6
as under the sink. (Optional, but strongly recommended and may be required by local codes.) • The water connection is on the left side of the dishwasher. Install the hot water inlet line, using 3/8" or larger copper tubing. Route the line as shown in Figure F and extend forward at least 19" from - Hotpoint HDA3540NSA | Installation Instructions - Page 7
Manual-Steps 18 and 21 • Product Samples and/or coupons-Step 21 • Conversion leads (Factory-equipped Power Cord Models Only) -Appendix STEP 2: CHECK DOOR BALANCE • With the dishwasher Inside of Frame Figure G Tip: Avoid service calls for door balance problems Make sure the spring end is fully engaged - Hotpoint HDA3540NSA | Installation Instructions - Page 8
break. • Position the end of the elbow to face the rear of the dishwasher. The power cord and connections must comply with the National Electrical Code, Section Power Cord Kit WX09X70910, available for purchase from an authorized GE Appliance Dealer, meets these requirements. 90° Elbow Figure K - Hotpoint HDA3540NSA | Installation Instructions - Page 9
GE appliance dealer. The 10 foot long hose is part number GPF10S. Hose Stop Do not use this port if present Hose Clamp STEP 9: INSERT DRAIN HOSE AND POWER CORD, IF USED, THROUGH CABINET • Upright the dishwasher authorized GE appliance dealers. • Refer to Figure P and follow the instructions - Hotpoint HDA3540NSA | Installation Instructions - Page 10
be approximately 3/4" behind the face of the adjacent cabinet. Refer to Figure R. Tip: Avoid unnecessary service charges for panel damage. Do not press on the center of panel with hands or knees when sliding dishwasher into position. 10 Figure R Check Level Side-to-Side • Adjust the level of the - Hotpoint HDA3540NSA | Installation Instructions - Page 11
90° Elbow Hot Water Supply Line Countertop Bracket Side Mount Brackets (optional) 3/4" Figure T Tip: Avoid unnecessary service charges for leaks or control p0a6neFl -d1am8a4g7eD. Make sure the dishwasher is centered in the cabinet and the door opens and closes freely without hitting the adjacent - Hotpoint HDA3540NSA | Installation Instructions - Page 12
Remove Drain Plug Tip: Avoid unnecessary service call charges fMoarkaensourderaaninyceoxm1cep8slsa7idn1rtaAinrhto1se has been pulled through the cabinet opening. This will prevent excess hose in the dishwasher cavity from becoming kinked or crushed by the dishwasher. Make sure the disposer plug has - Hotpoint HDA3540NSA | Installation Instructions - Page 13
the dishwasher came with a factory-installed power cord and you want to convert it to a permanent connection, refer to the instructions on page the dishwasher door and remove all foam and cardboard packaging. ■ Read the Owner's Manual to familiarize yourself with the operation of the dishwasher. ■ - Hotpoint HDA3540NSA | Installation Instructions - Page 14
Check for leaks around the door. A leak around the door could be caused by the dishwasher door rubbing or hitting adjacent cabinets. Reposition the dishwasher if necessary. See Steps 11, 12 and 13. ■ Most dishwasher models will drain about 3 minutes after the first fill. Check the drain line for leaks - Hotpoint HDA3540NSA | Installation Instructions - Page 15
both the access panel and toekick. STEP 21: LITERATURE ■ Leave the Owners' Manual, Installation Instructions, samples, and/or coupons with consumer. IMPORTANT - Screws are not interchangeable. To prevent damage to your dishwasher, use the proper screw in the proper location. Do not mix screw types - Hotpoint HDA3540NSA | Installation Instructions - Page 16
dishwasher harness by connecting like-colored wires. Figure CC • Return to Step 16 in these instructions to complete the conversion. Figure BB Remove Strain Relief Disconnect Powercord Figure CC Conversion Harness 06H-1949_Conversion Harness SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE GE
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
GE Consumer & Industrial
Appliances
Installation Instructions
Built-In Dishwasher
If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com
IMPORTANT
– The dishwasher MUST be
installed to allow for future removal from the
enclosure if service is required.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for
available custom panel kits.
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGS
shown throughout these instructions. While
performing installations described in this booklet,
gloves and safety glasses should be worn.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
IMPORTANT
– Observe all governing codes
and ordinances.
•
Note to Installer
– Be sure to leave these
instructions for the consumer and local inspector’s
use.
•
Note to Consumer
– Keep these instructions with
your Owner’s Manual for future reference.
•
Skill Level
– Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills.
Proper installation is the responsibility of
the installer. Product failure due to improper
installation is not covered under the GE
Appliance Warranty. See warranty information.
•
Completion Time – 1 to 3 Hours
. New installations
require more time than replacement installations.
STOP
BEFORE YOU BEGIN
Read these instructions completely and
carefully.