Hotpoint HDA3600RCC Installation Instructions
Hotpoint HDA3600RCC - 24" Dishwasher Manual
 |
View all Hotpoint HDA3600RCC manuals
Add to My Manuals
Save this manual to your list of manuals |
Hotpoint HDA3600RCC manual content summary:
- Hotpoint HDA3600RCC | Installation Instructions - Page 1
Appliances Installation Instructions Built-In Dishwasher Ifyou have questionsc,all800.GE.CARES(800.432.2737)or visioturwebsiteat:GEAppliances.com In Canada,call 1.800.561.334o4rvisiwtww.GEAppliances.ca BEFORE YOU BEGIN Read these instructions completelg and carefullg. IM PORTANT-The dishwasher - Hotpoint HDA3600RCC | Installation Instructions - Page 2
PARTS SUPPLIED IN INSTALLATION PACKAGE: [] Two 8-18 x 5/8" Phillips-head wood screws [] Junction box cover and #10 hex head screw [] Drain hose (78" long)and hose clamp [] - Hotpoint HDA3600RCC | Installation Instructions - Page 3
for proper drainage. , The dishwasher must be fullg enclosed on the top, sides and back. , The dishwasher must not support any part of the enclosu re. Plumb Floor MUST be Even with Room Floor Figure A Plumbing and Electric Service Must Enter Shaded Area • Make sure the floor is level inside the - Hotpoint HDA3600RCC | Installation Instructions - Page 4
waste tee or disposer and the air gap according to the manufacturer's instructions. CAUTION An air gap MUST BE USED if the drain hose is or 32" minimum, high drain loop will result in improper draining of the dishwasher, which mag cause damage. Cabinet Preparation Drill a 1-1/2" diameter hole in - Hotpoint HDA3600RCC | Installation Instructions - Page 5
on the appliance. Grounding Instructions - Power Cord Models This appliance must be service representative if gou are in doubt that the appliance is properlg grounded, Do not modifg the plug provided with the appliance to Dishwasher Electrical connection is on the right front of dishwasher. , - Hotpoint HDA3600RCC | Installation Instructions - Page 6
as under the sink. (Optional, but stronglg recommended and mag be required bg local codes.) ,, The water connection is on the left side of the dishwasher. Install the hot water inlet line, using 3/8" or larger copper tubing. Route the line as shown in Figure F and extend forward at least 19" from - Hotpoint HDA3600RCC | Installation Instructions - Page 7
drain hose clamp- Step 7 , Owners' Manual- Steps 18 and 21 , Product Samples and CHECK DOOR BALANCE • With the dishwasher on the wood base, check G Tip: Avoid service calls for door balance problems. Make sure the remove the two top 8-32 x 1/4" machine thread screws. , Slide the access panel - Hotpoint HDA3600RCC | Installation Instructions - Page 8
feet. Power Cord Kit wxogx70910, available for purchase from an authorized GE appliance dealer, meets these requirements. 90 ° Figure K Tape Valve Bracket Junction Box Bracket t Ground White STEP 7: INSTALL DRAIN HOSE TO DISHWASHER DRAIN PORT Skip this step if drain hose has been preinstalled - Hotpoint HDA3600RCC | Installation Instructions - Page 9
dishwasher is approximately 78" long. If u longer hose is needed, a 10-foot-long hose may be purchased from an authorized GE appliance dealer. The 10-foot-long hose is part with the base of the dishwasher and components under the dishwasher. Tip: Avoid unnecessarg service charges for no fill, drain - Hotpoint HDA3600RCC | Installation Instructions - Page 10
when the level indicator is centered left to right and front to back. The dishwasher door should close without hitting the sides of the tub. • Replace the lower rack. Tip: Avoid unnecessarg service charges for poor wash performance and rack operation. Pull the dish racks half wa U out. The U should - Hotpoint HDA3600RCC | Installation Instructions - Page 11
the compression nut. 90 ° Elbow Hot Water Supplg Line Side-Haunt Brackets (optional) Figure T Tip: Avoid unnecessary service charges for leaks or control panel damage. Make sure the dishwasher is centered in the cabinet and the door opens and closes freely without hitting the adjacent cabinets - Hotpoint HDA3600RCC | Installation Instructions - Page 12
to a disposer, check to be sure that the drain plug has been removed. Dishwasher will not drain if plug is left in place. • Connect drain line to the hose with a screw-tLIpe clamp. Drain 4 RePmluogve Tip: Avoid unnecessary service call charges for a "no drain" complaint. Make sure ang excess drain - Hotpoint HDA3600RCC | Installation Instructions - Page 13
If the dishwasher came with a factory-installed power cord and you want to convert it to a permanent connection, refer to the instructions on page dishwasher door and remove all foam and cardboard packaging. [] Read the Owner's Manual to familiarize yourself with the operation of the dishwasher. - Hotpoint HDA3600RCC | Installation Instructions - Page 14
WET TEST CHECKLIST [] Turn on power supplg or if power cord is used, plug it into the wall outlet [] Latch dishwasher door [] For electronic dishwashers, select the NORMAL WASH cgcle and press the START pad one time U i i@ C_J_s Options c_,,_ IS - Check the electrical connection to the water - Hotpoint HDA3600RCC | Installation Instructions - Page 15
' Manual, Installation Instructions, samples and/or coupons with consumer. IMPORTANT - screws are not interchangeable. To prevent damage to your dishwasher, Tip: Prevent tub damage and reduce sound from under the dishwasher. Use the machine-thread screws in the top holes and the sheet metal-thread - Hotpoint HDA3600RCC | Installation Instructions - Page 16
. Remove and discard the power cord. . Connect the conversion harness (included with dishwasher) to the dishwasher harness by connecting like-colored wires. See Figure CC. . Return to Step 16 in these instructions to complete the conversion. / / / / ! / 11 Figure BB Remove Stroin Relief Disconnect - Hotpoint HDA3600RCC | Installation Instructions - Page 17
Appareils m_nagers GE Consumer and Industrial Instructions d'installotion L(]ve-v(]isselle enc(]str Pour toute d6faillance du produit attribuable 6 une installation inad6quate n'est pas couverte par la garantie de GE. Reportezvous 6 la garantie du produit. • Dur6e de I'installation - Entre 1 et - Hotpoint HDA3600RCC | Installation Instructions - Page 18
externe NPT de 9,5 mm [3/8 pal 6 une extr6mit6 et I'autre extr6mit6 conque pour le raccordement 6 la conduite d'alimentation en eau) [] Ensemble de supports de montage lat@aux GPF65 si le comptoir est en granite POUR UNE NOUVELLE INSTALLATION : [] COble 61ectrique [] Conduite d'alimentation en eau - Hotpoint HDA3600RCC | Installation Instructions - Page 19
Preparation pour I'installation - Ouverture dans les armoires PRI_PARATION DE L'OUVERTURE DANS LES ARMOIRES Pour r_duire les nsques de choc _lectrique, d'incendie ou de blessures, Hnstalleteur doit s'essurer que le lavevaisselle est compl_tement encastr_ au moment de I'installation. • L'ouverture - Hotpoint HDA3600RCC | Installation Instructions - Page 20
Preparation pour l'installation - Vidange PREPARATION DE LA PLOMBERIE POUR LAVIDANGE Exigences relatives au syst_me de vidange • Veuillez observer les ordonnances etles codes Iocaux en vigueur. • Le bogau de vidange doit avoir une Iongueur maximale de 3 m_tres (10 pieds). • II faut pr_voir une - Hotpoint HDA3600RCC | Installation Instructions - Page 21
Preparationpour l'installat-iAolnimentationlectrique PRI_PARATIONDU CABLAGE I_LECTRIOUE POUR VOTRE SI_CURITEPERSONNELLE : Enlevezlefusibleou d_clenchezle disjoncteurau panneau de distribution principaalvant de commencer l'installatiNo'nu.tilisepzas une rallonge _lectriquoeu un adaptateur de - Hotpoint HDA3600RCC | Installation Instructions - Page 22
Preparationpour l'installat-iAolnimentationen eau chaude PRI_PARATION DE L'ALIMENTATION EN EAU CHAUDE Conduite d'eau chaude • Lo conduite peut entrer du c8t6 gauche, du c8t6 droit, de I'arri_re ou du plancher dans la partie ombr6e indiqu_e dans la Figure R , La conduite peut passer par le m_me trou - Hotpoint HDA3600RCC | Installation Instructions - Page 23
Installation du lave-vaisselle ATTENTION N'enlevez pas la base de bois avant d'etre pr_t _ installer le lave-vaisselle. Si vous enlevez la base de bois, le lavevaisselle pourrait basculer Iorsque vous ouvrez la porte. ETAPE 1" PREPARATION Prenez les pisces fournies dans I'emballage et mettez-les de - Hotpoint HDA3600RCC | Installation Instructions - Page 24
joints filet@s sur les filets du coude de 90°. Vissez le coude de 90 ° dams I'@lectrovanne. Ne serrez pas le coude de faqon excessive; le support de I'@lectrovanne pourrait se d@former ou le raccord de I'@lectrovanne pourrait se casser. Tournez I'extr@mit@du coude pour qu'il pointe vers I'arri@re - Hotpoint HDA3600RCC | Installation Instructions - Page 25
les vis 5 bois. Vous pouvez vous procurer I'ensemble GPF65 aupr_s d'un d_taillant autoris_ d'_lectrom_nagers GE. , Reportez-vous 5 la Figure Pet suivez les directives donn_es dons I'ensemble. Supports de l_ montage lat@aux q Figure N Conduite d'alimentation en eau C6ble d'alimentation 61ectrique - Hotpoint HDA3600RCC | Installation Instructions - Page 26
Installation du lave-vaisselle I_TAPE 11" INSTALLATION DU LAVEVAISSELLE DANS L'OUVERTURE IM PORTANT - Ne poussez pas sur le panneau avant avec vos genoux. Vous pourriez endommager l'appareil. • Saisissez le panneau avant de I'appareil par les c6t@s et faites glisser le lave-vaisselle dans I' - Hotpoint HDA3600RCC | Installation Instructions - Page 27
du comptoir et vissez-les dams le comptoir. • Si le comptoir estem granite ou em um mat@riau similaire, vissez les vis Phillips dams les supports de montage lat@raux et dams les armoires adjacentes. • Assurez-vous de visser compl@tememt les vis biem droites afire d'@viter toute imterf@remce avec - Hotpoint HDA3600RCC | Installation Instructions - Page 28
Dishwasher Installation ETAPE 15 • RACCORDEMENT DU BOYAU DE VIDANGE L'extr_mit_ moul_e du bogau de vidange est conque pour s'installer sur I'orifice d'entr_e d'un diam_tre variant entre - Hotpoint HDA3600RCC | Installation Instructions - Page 29
blanc, et le fil noir au fil noir. Remarque : Assurez-vous de faire passer ies fiis du faisceau de conducteurs par ie petit trou du support Support de la boite de jonction Mise 5 la terre Blanc \ Figure Z I_TAPE 17" INSTALLATION DU COUVERCLE DE LA BOITE DE JONCTION Si le couvercle de la - Hotpoint HDA3600RCC | Installation Instructions - Page 30
-le dans la prise de courant murale. [] Verrouillez la porte du lave-vaisselle. [] Dans le cas des modules @lectroniques, s@lectionnez le programme NORMAL WASH (Salet@normale) et appuyez une fois sur la touche START (Mise en marche). ..C_s kJ Options c_, kJ - V@rifiez le raccordement 61ectrique - Hotpoint HDA3600RCC | Installation Instructions - Page 31
Installation du lave-vaisselle I_TAPE 20" RI_INSTALLATION DU PANNEAU D'ACCES ET DU PANNEAU INFI_RIEUR Au cours de cette _tape, vous aurez besoin des panneaux et des deux vis mis de c6t_ 6 I'_tape 4. Deuxtgpes de vis sont utilis_s. Lesvis n ° 8-32 x 6,3 mm (1/4 po)sont utilis_es a la portie - Hotpoint HDA3600RCC | Installation Instructions - Page 32
Annexe TRANSFORMATION D'UN LAVE-VAISSELLE DOTI_ D'UN CORDON D'ALIMENTATION INSTALLI_ #, L'USINE EN VUE D'UN BRANCHEMENT PERMANENT Pour uccomplir cette procedure, vous uvez besoin des ills pour lu conversion mis de c6t_ 5 I'_tope 1. , Assurez-vous que le cordon d'olimentotion du luve-voisselle est
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
 |
 |
(]_[Z" F"
-
.
.
o'
I_,,
.......
i!
_,. °_,,
i
,;
.........
,,y
o_<,.
I
(_;_
C');(
If I{.]t.l,<::;_>.(_
Appliances
Installation
Instructions
Built-In Dishwasher
Ifyouhavequestions,
call800.GE.CARES
(800.432.2737)or
visit
ourwebsiteat:GEAppliances.com
In
Canada,
call
1.800.561.3344
orvisit
www.GEAppliances.ca
BEFORE YOU BEGIN
Read these instructions
completelg
and
carefullg.
lMPORTANT-
Observe
all governing
codes
and ordinances.
• Note to Installer-
Be sure to leave these
instructions
for the consumer
and local inspector's
use.
• Note to Consumer
- Keep these instructions
with
your Owner's
Manual for future
reference.
• Skill Level - Installation
of this dishwasher
requires
basic mechanical,
electrical
and plumbing
skills.
Proper installation
is the responsibility
of
the installer.
Product
failure
due to improper
installation
is not covered
under
the GE
Appliance
Warranty.
See warranty
information.
• Completion
Time - 1 to 3 Hours.
New installations
require more time than
replacement
installations.
IMPORTANT-The
dishwasher
MUST
be
installed
to
allow
for
future
removal
from
the
enclosure
if service
is required.
If gou received
a damaged
dishwasher,
gou should
immediatelg
contact
gout
dealer
or builder.
Optional
Accessories
- See the Owner's
Manual for
available
custom
panel kits.
FOR YOUR SAFETY
Read and observe
all CAUTIONS and WARNINGS
shown
throughout
these
instructions.
While
performing
installations
described
in this
booklet,
gloves and safetg
glasses
should
be worn.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
206C1559P195
31-30255
07-09
.JR